@@ghaniguerrad5061 How can you help me find more time for such projects? I'm already learn a lot Unreal Engine technology to create electronics simulator using style, you seen on this video. But this technology is hard and I need support, people who help me do this project... if you know some UE developers, contact me whith them, i think in team will be easier creating such things...

Usually O2 sensor receive the supply directly from ECU and generating signal through heat and amount of oxygen also directly by single wire. Maybe in very new models signal is transmirred via CAN bus, it should be check in mercedes WIS documentation. New Isuzu truck generare lambda signal and transmit them via CAN indeed.

@@reverseengineering2943 ok. I'm having problems with one o2 sensor and I changed it like 3 times, checked the wires, replaced the ECU and still having the same problem. I was thinking it was a CAN Bus issue so I been watching a lot of videos about this... but I don't know what can be

@@M-Angel25 you have to check wire diagram of your engine electronics system and check from which pins of ECU wires going to O2 sensor plug. Than check continuity of wires using multimeter and if wires is good, repait ECU. No CAN BUS issue.

I'll making circuit game, using Unreal Engine. The project is huge and first effects are far, but could be interesting. Cheers!

Again thanks and hope for More new technology learning

Thank you. This is old technology, not used today so don't worry. If you are determined to be asembly language hacker, then you find the way to understand this. Good luck.

I have experience with making android car app connection with VAG group. My android-radio supplier gace my tutorial how to set this unit to different car, but it was around two years ago, so today's units and android systems could be different..

Cześć. Właśnie dziś o tym gadałem z kolegą, bo mamy najnowszą Stardiagnosis z programami Vediamo i Monaco, którymi modzi się w Mercach jak inżynierowie Daimlera, coś jak eSYS w bmw, ale wiesz, wciąż czasu brakuje... Ale trzeba mieć nadzieję, jakbyś miał ciekawe tematy to pisz [email protected]

Hi friend. I used Blender 3D. It was old project and today a lot of details i would make another way, but using Blender too.

This is not AI channel. AI do nothing for creating this animations and videos, all is very hard working and many years experience bro. Stay tuner.

I didn't use EEPROM for such microcontroller, but EPROM only. It's difference between these memories, but it was described well in 8051 microcontrollers book from such Hindi proffersor, and title of this pdf was something like "8051 assembly and c programming ".. if I'll find this book i will send you more details

I think you should check WIS/Stardiagnosis wiring diagrams to understand whole CAN bus architecture. I'm sure obd diagnostic CAN isn't blocked, but with newer standard impemented and you trying to using wrong technology to sniffing them. Everything starting from understand network architekturę and without good documentation it's impossible i think..

Thanks man. Yes, my few years experience of repairing, implementing, and designing CAN buses in cars gave me possibilities to creating this animation. It was specific state of my mind, when I created them.. Also planned making more stuff like this, but lost motivation. Thank you again for this comment, maybe I'll back to this education project in futures. Greetings from Poland!

I think one of motorola procesor inside EIS (Electronic Ignition Switch module - key switch) lost eeprom data. But first of all check all fuses and EIS operation - if cannot turn key in ignition switch - it also can by EIS fault reason.

Thanx...key is turning freely..starter is running but engine does not start...

It depends what you mean 'can bus adapter'. In fact there is No can wires in obd connector (confirmed in 2,7cdi - pin 6 and 14). So I used directly ECU (and all others units) connectors. Most of all CAN buses is connected to EAM / AAM units in late w163 vehicles. So you have to find unit's pinout, i.e. from Stardiagnosis software (star finder), and plug measure needles into unit's connector and needles wiring to CAN-USB adapter, i.e peak, vector, or something cheaper.. then chose proper can speed and recording. That's how I made my sniff.

Thank you very much, my friend. Did you see my last project here: kzbin.info/www/bejne/p4K4eoiId9StY9U

Nie wiem, zapytaj autora.