Jim Taylor

Пікірлер

@Ramshackle6984 3 күн бұрын

I can confirm this works. I have a 2016 Sportsman 570 that started having weird throttle issues. I troubleshot it and replaced the TPS and IAS, but didn't realize how precise the TPS had to be. Today I decided to give this a try. I used a computer power supply. A computer power supply 4 pin Molex connector has 5v on the red pin and ground on the black pin. I connected a piece of jacketed wire to one of the red pins and one of the black pins on the Molex connector. A 5v USB charger would work too, but the power supply has much better tolerance +/-. I then attached the wires from the Molex connector with small spade connectors to the pins on the TPS. Looking at the TPS connector from the wiring harness; orange is 5v in, green is voltage out, purple is the ground. I connected my red wire from the power supply to the left (orange) pin, connected the black wire to the right (purple) pin. I squeezed my red multimeter probe in to sit on the middle (green) pin and let the black probe sit on some bare wire where the black wire went into the Molex connector ground (set the multimeter to DC voltage and within voltage range .5-5v if it's not auto sensing). I then used a paperclip to jump the power supply to turn it on without a switch connected (ATX 24pin green to black pin jumper). The purpose is to supply the TPS 5v and measure what comes out of the middle pin. I can confirm that setting idle to .46v worked perfectly and my ATV runs great again! Thanks Jim for the video that pointed me in the right direction! I refuse to pay a dealer or shop their ridiculous prices to fix things when it can be done with common tools and some know-how. 👍

@jmd2k Ай бұрын

I paid $79 for mine a very very long timed ago. Best bore sighter ever built. I just used it to sight in a red dot on my son’s Sig Sauer air rifle. I came across this video because it’s been so long since I used it that I can’t remember and wanted to see if your video showed how to change the battery. Anyway I found a work-around by shining a flashlight on the back side of it to light up the crosshairs in it and it worked! I’m never giving this one up and will hand it down to my son.

@thilau5715 Ай бұрын

...pour le cadrage il craint personne lui!😩😜😂

@travishead372 8 ай бұрын

I have a question what is the out put setting if you messed up the throttle body screw I was wondering what the numbers were when the screw Is all the way out so I can reset it

@jeffbederian 8 ай бұрын

It’s more than a bore sight. You can use it to predict POI before firing ANY rounds as long as you have a good idea of the rounds muzzle velocity.

@joevelasquez1842 11 ай бұрын

tfhis video was very help full

@rodneyl.8695 Жыл бұрын

Great video and info. Appreciate the way it’s presented. Make some more.

@jeffrme Жыл бұрын

Roll Tide! Thanks for the help.

@everydaycar3518 Жыл бұрын

You know you can just plug it into machine and check on red and yellow wire I think that’s for 800 idk about 570 I’m sure it’s about the same

@mattpie595 Жыл бұрын

Very informative. I’ve got one and will clean it before trying it out. Thank you!

@nickspann20 Жыл бұрын

I tried to buy one years ago right as they were being discontinued. I thought it was a great design. I still wish someone would come out with something similar for a better price

@corysnladventures2758 Жыл бұрын

I would like to see you do pattern tests with the original full choke and aftermarket chokes to compare

@jimtaylor3544 Жыл бұрын

I will say a Primos Tight Wad choke with TSS federal shot, will hammer a Turkey at 75 yards. I have tried multiple chokes the Primos isn’t costly and it works well with the 935.

@heethen112 Жыл бұрын

Stole my wife’s vibrating decoy, she says it makes her quiver.. cost me my marriage, was way more than $20.. I’m blaming you, so, thanks!!

@chriswilliams6228 Жыл бұрын

Is it supposed to be .46 or .68?

@jimtaylor3544 Жыл бұрын

.46

@FPCCEM Жыл бұрын

Jim, this was extremely helpful. Thank you for taking the time!

@thomasstager6177 Жыл бұрын

What is you volt meter set to

@mikemarks6562 2 жыл бұрын

Ok that’s why mines won’t cycle then the packing grease I got a 935 water fowl edition away grass pattern love it just gotta get it to cycle 2/34

@danielstidham8936 2 жыл бұрын

Do a video on gas and inertia that would be helpful

@peterstone833 2 жыл бұрын

I have one. Bought it years ago. Works great. Awesome boresighter to have and carry with you in the field.

@jimmybeason971 2 жыл бұрын

Which color wires do you mailed the jumper to? That’s pretty important don’t you think

@jimtaylor3544 2 жыл бұрын

I don’t have that atv anymore, but pin the green wire I believe it was brown but for pin the green wire and the wire beside it in the orientation show in the video

@jak751 2 жыл бұрын

He tells you.

@bradw1808 2 жыл бұрын

This is a mil 23 code correct? Not the "-" code 23.

@jimtaylor3544 2 жыл бұрын

It was a active code for the o2 sensor the atv had lower power, after replacing the sensor power was good but engine light still on,so have to perform the code reset procedure.

@AsaSpades112 2 жыл бұрын

does the blinking light off after you clear the code?

@jimtaylor3544 2 жыл бұрын

It does if the code was resolved.

@locknnload 2 жыл бұрын

i am really interested in buying one of these after I saw my pawn shop using one bore-sighting my new rifle looked on eBay and there was one for sale for 279.00!!! i wait to find one cheaper one day

@wp4565775 3 жыл бұрын

I just found mine in a drawer that I had bought about 10 years ago. I used it 3 or 4 times and then just lost interest in guns. Anyway I came to YT to see how to change the batteries. It was the bee's knees as far as I remember.

@randallturner7763 3 жыл бұрын

Have same gun love it

@jbk16619 3 жыл бұрын

Recently bought a 935 and found out it wouldn't shoot 2 3/4 very well. So I searched YT and found your video. Thanks, great info. Good video. I realize your original video is 3 yrs old but I, like some of the others, would like to see a video of the breakdown/clean/oil and reassemble.

@galenmcdonough6999 3 жыл бұрын

What do you use for grease? I’ve just been using high heat grease on my 935 and the only think I can get to cycle through it is 3 or 3.5 and it’s picky about brand. I’ve put 300 3 inch shells through it so I figured it should be broken in by now as well.

@jimtaylor3544 3 жыл бұрын

Galen McDonough Slip2000 is my favorite grease, and the lighter you coat it the easier the guns parts will operate. I would make sure the 935s gas piston is clean under the fore grip and make sure the rail is lubed that is where the power of shell extraction comes from. I have seen shotguns with spotless chambers but the gas impingement system is dirty causing the ejection issues. I have had my 935 for 6 years now and it has been it the bottom of swamps in Alabama to muddy fields of Arkansas and it still is the best auto I own.

@galenmcdonough6999 3 жыл бұрын

Jim Taylor , Thank you, yeah I’ll definitely try that maybe I’ve just been to heavy with the grease, I have cleaned the gas system multiple times, since it is gas operated and my main problem is stove piping shells. I’ll definitely look into that grease and just giving it a light coat

@kevinberdine 4 жыл бұрын

Thanks for posting this!

@weschapman2237 4 жыл бұрын

Looking at one. Of these are overboard barrels worth it..buckshot?

@bobhunt1253 4 жыл бұрын

Thanks. I’m looking at one and you pushed me over the edge.

@flounderwetspot8524 4 жыл бұрын

Just got a 935 turkey and love it. Especially with the or3gun enhanced field kit. The weight is on the heavy side but manageable for sure.

@rschittenhelm1587 4 жыл бұрын

I BOUGHT THE 935 4 YEARS AGO AND ONLY 200 ROUNDS BEFORE IT FAILED... THE TOP OF THE FIRING PIN BLOCK BUSTED OUT,, IT WASN"T FILTHY BUT SOME BULID UP,, THEY SAY NO OIL,DRY SPRAY LUBE ONLY, OIL CREATES BUILD UP,, SENT TO MOSSBERG,, AND BOUGHT A SX4 !!!

@e954rr2 4 жыл бұрын

My 935 will not cycle 2 3/4

@wncrcandoffroad3919 4 жыл бұрын

Mine wouldn't either.

@caleb7mm 5 жыл бұрын

$20 decoy, $900 yeti hat

@kerrmartin3498 5 жыл бұрын

Are you using a heavier H2 buffer?

@jimtaylor3544 5 жыл бұрын

It is a standard PSA buffer.

@mgshook1721 5 жыл бұрын

Think you should do a video on the stripping the gun down and greasing that you talked about

@BRGOutdoors 6 жыл бұрын

Good video man! Just bought the waterfowl pro series. If you have time would you do a disassembly and reassembly video? Just throwing it out there.

@bbmopar3834b 6 жыл бұрын

Great video. I was actually at a local gun shop handling the 930 and thought that was better because it would cycle the 2 3/4. But now that I know the 935 can cycle them I'll see about getting the 935.