OK, Do you have a parts list, or measurements to make this mod..? Can't really get the details from video. Thanks

This is exactly what I'm looking to make for mine. Can you please send me the link, I would like to build a lift on my splitter. Thanks

Do you have a bidet? If so can you explain how this works? Does it make the solids bucket too wet?

Thanks for this great fix! I installed a Home Depot Store SKU #1001293165 piece I cut to size. 4 x 12 inch. I included the bent ridge edge along the bottom to make it rigid on the far end. I held in place with a block of wood on the left side. I drilled one hole in the metal plate and put a screw into the wood so it wont vibrate loose. I'm very confident it will work. Thanks again!

how did you seal the outlet and sensor holes?

Good idea!

(This dance sequence is "Brooklyn Transfer" by Maia McCormick and Michael Karcher.)

Wow man , you did a great job and you showed us how it works. I just watched a couple videos and they never showed the inner workings of the thing. Thanks for sharing. ✌️👍🇺🇸

Did it do any damage to the leaf springs or the bolts that hold the leaf springs like bend them ?

What is the purpose of using the chains rapped around both sides of axle like you showed in part 2?

i measured from the driveway to bottom of axle its 7.25 I had a thought maybe I could put a extra axle u bolts and plate the and just have them just a little tight so the flat plate is at the bottom of axles they are only like 4 inches wide and then put jack under that flat plate just to distribute some of the pressure of the jack

What size boards did you use a 4x4 or 6x6 ? one of my front axles are bent the top is leaning in a little i had a thought of using like 3 or 4 mufflers clamps on the bottom of axle to hopefully keep the axle from crushing in and use the boards like you have yours i do have a 3 ton jack on wheels but by the time you put jacks and 6x6 or 4x4s under it i think I would have to have trailer really high what's your thought ?

How did you tie chains down ?

I bet you need a stronger hydraulic jack. That floor jack may only be a 3 ton. Fyi, I tried a 12 ton bottle jack and it wasn't strong enough to straighten out a 7000 pound axle so I'm going to try a 20 ton bottle jack.

Nice job with the plastic weld! I was hesitant when you snapped the lens onto the base but it's solid as a rock. Also a more sustainable way to live, very inspirational video!

I have a Bolens similar to yours. That thing is a beast. I bought it 3rd hand, and only paid $50 for it 10 years ago. Still starts every time. Not as powerful as a new Ariens, but still reliable

Hi David! This is Christie from the Philippines (Florida). Nice to see you and nice to see your videos!

Hello ,do You still have that snowblower? If you do i have question.Would you make picture of linkage carb connections,and governor. Thank u

I have this exact generator. Mine won’t start and can’t find the carb anywhere online! Do you have a model number for the carb you replaced it with? Will help me a lot!

Thanks for the video. I'll copy your technique to straighten my trailer axle. It bent hauling 2400 lbs of gravel in a trailer rated for 1400 lbs when I hit a big frost heave on the road. Even though I was impressed at how tough this little utility trailer is, I won't do that again.

Thank you.

I did the same thing. But I fill my tanks up with water.

I can't believe you don't wear gloves.

I really appreciate this video! I never would have found the panel allowing access to the location of the mouse nest in my 2009 Fit. Yesterday I removed the panel, cleaned out a large pile of shredded bedding, and installed a piece of ¼-inch hardware cloth about 11½ x 5½-inches over the hole leading down to the cabin filter. I wedged the screen in place using wooden blocks at each end. I hope it works! Thank you!

Thankyou

Just curious- did the wheel bearings survived this technique?

Well it’s not a lifetime filter there Tommy boy

I had the same exact washing machine from 1993-2021 but it had the flex vane pentascrub agitator. My old Whirlpool washing machine was replaced with a Speed Queen TR7 model.

stunning Videos

Extraordinary

Ahhhhhh 💜 Yesyesyesyesyesyesyes you're awesome #mtvhottest #trending

Hello I wonder if this is how it’s done on a 2003 Toyota Avalon?

Thank you for sending that link. It showed me exactly what I wanted to see, which was how you attached the ram to the table.

Nice job with the rebuild, very clearly explained and demonstrated. Was this the original OEM Toyota alternator? Great video, thanks for posting!

if you all can"t fegure out how to build it; don"t try its not rocket science work

Please make a video on how you constructed your tilting table, especially how it connects to the ram. Thanks

Thanks for the video, I have problems with mice going into the cabin, will try your recommendation soon

nuttin' like some good old wet stringy red oak! HA HA And why did I have to watch all that just to see one use of the lift?

Nice job god bless

Nice job god bless

I have same log splitter, hate it!! but your invitation is very nice , I will duplicate it, getting to old to be picking big ones up!! (47 yes old )

Nice job explaining the fix and saving this leaf blower, well done!

hi there nice job john

Nice job troubleshooting and fixing the Thermacell! I haven't seen one of these units in a long time, but remember how effective it was at keeping mosquitos away even in the dead of summer. Your clip installation was seamless, making the Thermacell that much more versatile. Great video!

Need to show how it actually works, ie how the cylinder raises the lift.

Not sure I'd call it super quiet. What was done to quiet it down? The sound that it's making does sound more of a rattle than the traditional compressor sound.

Cats are evil, Christmas lights are awesome :D

That is very nice and well thought out.

Sounds like a smooth-running engine, that snowblower is ready for a blizzard! Do you plan on doing any routine maintenance before the first storm?

Can you please make a video on how you made it?