When you see chickens running around and a cold beer at the end, you know this guy knows his sheeet
@z2motorsports176Ай бұрын
New subscribe
@SFFRACINGАй бұрын
Thanks 🤘
@shanewright69582 ай бұрын
Another great video. Keep them coming 👍👍
@SFFRACING2 ай бұрын
Thanks man 🍻
@billycostabile86382 ай бұрын
I'm about to order one off of Amazon it's a 3/8 by 1 inch is this what you used
@SFFRACING2 ай бұрын
3/4 to 1 inch
@ToddHLHG2 ай бұрын
Good to see a video from you! Are you guys coming home for grafitti? I was polishing the camaro today...getting it ready for grafitti...we are heading up thursday.
@SFFRACING2 ай бұрын
im probably coming up the week after grafitti sadly... hope you guys have a blast thanks for watching man
@ToddHLHG2 ай бұрын
@@SFFRACING you are welcome....we are looking forward to it.
@jamesangell18622 ай бұрын
i'm considering doing the same for my 1994 gt. great video! thanks
@charliemunoz54432 ай бұрын
Do you know the driveshaft length I bought a caprice and trans is out of car so I can measure and I can’t find it anywhere
@SFFRACING2 ай бұрын
I don't sorry
@DaleLeathers2 ай бұрын
Great video! If you have the time I need help with the wiring aspect. Also I did see you using a fuel regulator. Did you change fuel pump? I've seen plenty of videos with individuals changing from efi- to carburated. There all fox. Your is the only sn95 which I also have.
@SFFRACING2 ай бұрын
I just found a pinout of the factory harness and removed the wires I didn't need anymore...yes a holley bypass regulator with the stock pump and it worked excellent
@MurphRocks863 ай бұрын
This video helped me a lot in doing mine! The entertainment factor was great too, lol.
@SFFRACING3 ай бұрын
Hell yeah haha
@ronjlwhite80583 ай бұрын
Welcome back bro. Gonna be a nice ride when done.
@SFFRACING3 ай бұрын
Thanks brotha 🤘
@shanewright69583 ай бұрын
It’s been a long time my friend 👍👍
@SFFRACING3 ай бұрын
Glad to be back
@rickybonesause24994 ай бұрын
did u have to use a shaft adapter for the clutch
@SFFRACING4 ай бұрын
Yes a 3/4" to 1" keyed adapter that I welded in the clutch
@rickybonesause24994 ай бұрын
@@SFFRACING would a 420 fit in there aswell
@alltruenews4 ай бұрын
I’ve never seen a person paint so incorrectly. You apply paint in one motion and spray past what you’re painting. Starting and stopping in the middle of a panel creates a build up of paint each time you switch directions - making high and low deposits of paint.
@SFFRACING4 ай бұрын
We were drunk lol
@LarryDawson-hi7ue4 ай бұрын
Great job but really bid shouldn't let your sweet baby have a screw driver she could very easily fall
@thepubliceye4 ай бұрын
My pump sent shards of aiuminum throuhg the cooling system and plugged my heater core.
@SFFRACING4 ай бұрын
Damn
@ziffification5 ай бұрын
Did you have that recal l to add the voltage amplifier for fuel gauge
@SFFRACING4 ай бұрын
Not that I know of
@codymarsh81175 ай бұрын
My girlfriend measures..things the same way. 😂
@SFFRACING4 ай бұрын
🤣🤣🤣
@hhhhhh20625 ай бұрын
What distributor? Uni-lite in the same process just 600 double
@SFFRACING5 ай бұрын
Msd distributor with no vacuum advance
@hhhhhh20625 ай бұрын
@SFFRACING Part number by?cross reference the MSD set up I have now.Just need AL6 if I am good on distributor I have. Thanks
@youteo35965 ай бұрын
Put the PBR/crack pipe down and step away from the Caprice slowly...
@SFFRACING5 ай бұрын
🤣🤣🤣
@ThePascalmovies5 ай бұрын
4.44 5 speed? With stock ecu?
@SFFRACING5 ай бұрын
4:10 4 speed auto
@America-he5tz5 ай бұрын
Wish i knew about this. Id enter mine in
@williamlittig72665 ай бұрын
Definitely a four can car. If you did it right
@SFFRACING5 ай бұрын
We were drunk definitely didn't do it right lol
@user-kl7up2dh7x6 ай бұрын
Hey man about to do the same thing with the starter generator, does yours continue running while the motor runs or does is switch over to generating power? Awesome video
@SFFRACING6 ай бұрын
It swaps over to generator after it starts I left all the controller for that in there...thanks man 🤘
@eddiereveron89554 ай бұрын
Man I’m in the process of putting 440 Duromax in my g14. How do you wire the starter generator? I wanna keep this working like factory
@SFFRACING4 ай бұрын
@@eddiereveron8955 I left all the factory wiring for the generator
@eddiereveron89554 ай бұрын
I’m not iré I remember where the wires go lol. I just pulled everything out. Wires are all there. Gotta find a spot for generator and figure out what wire kills the coil
@mitchmurrell7536 ай бұрын
At least it will be one color...
@juniorreillo2646 ай бұрын
Waoo . Started day time n its night time n still painting waoo something is wrong.. 2 hr max to paint a car
@SFFRACING6 ай бұрын
I mean it only takes about 45 minutes for it to get dark here
@bradleyhanlon6 ай бұрын
Are you using the stock CCRM or did you eliminate and use relays for fuel pump, fans and a/c?
@SFFRACING6 ай бұрын
Eliminated the ccrm it was giving me a ton of problems
@Automated147 ай бұрын
F’ing ‘MURICA 👍🛠️✔️
@djclay777 ай бұрын
I just did a carb conversion on my 95 GTS. Question, did you use the tach signal wire off the engine harness for any particular reason? Or just convenience? I have my ECU still and kept the oil and water temp wires off the harness, I might try the signal wire like you did
@SFFRACING7 ай бұрын
It was the shortest run and convenient is really the only reason
@djclay777 ай бұрын
@SFFRACING do you recall the pin # on the 42-pin plug? Thinking I might just do the same
@windowtintman19863 ай бұрын
@@djclay77 I'm going to assume you'll have to undo the wires from the injector harness and track the three wires down and do away with the remaining.
@djclay773 ай бұрын
@windowtintman1986 That's exactly what I did. Found the tach signal wire, 1 of the corner wires on the 42-pin connector. All factory gauges working now
@tims86037 ай бұрын
Not on a car like that. Those are classics. You shouldn't go back and forth like that. Paint one section at a time. Start at one edge and move in one direction. Very light coat. Do all the sections and then come back and go over them again.
@shanewright69587 ай бұрын
Great job. Another great video 👍👍
@SFFRACING7 ай бұрын
Thanks brotha
@ToddHLHG7 ай бұрын
The engine sounds great.....Another great video my friend.
@SFFRACING7 ай бұрын
Thanks brotha yeah it runs sweet I'm glad to not have to worry about it anymore lol
@ToddHLHG7 ай бұрын
@SFFRACING I bet! Looking forward to your next video.
@motor_citymuscle2887 ай бұрын
Do you have a link for the adapter fitting and fuel lines you got?
@djclay777 ай бұрын
Check out K-Motor performance (that's what it looks like the OP used). They make a 6AN Push On Fitting for 5/16 (Feed) and 1/4 (Return) hard lines. The rest should be regular 6an fitting from like Russel or Evil Energy....etc
@motor_citymuscle2887 ай бұрын
@@djclay77 damn man! Thanks for sharing great website! I’m converting my 95 GT
@SFFRACING7 ай бұрын
Thanks man that's exactly what I have
@djclay777 ай бұрын
@SFFRACING familiar territory, bought the same fittings in 2022. Been holding up great
@tjkilshot8 ай бұрын
Is that stock internals
@SFFRACING8 ай бұрын
Motor is untouched
@tjkilshot8 ай бұрын
I'd assume the trans is untouched as well besides basics?
@SFFRACING8 ай бұрын
@@tjkilshot has a shift kit
@richardwest47228 ай бұрын
Good job!
@shanewright69588 ай бұрын
Another good one 👍👍
@SFFRACING8 ай бұрын
Thanks brotha
@ToddHLHG8 ай бұрын
Merry Christmas to you all
@SFFRACING8 ай бұрын
Merry Christmas to yall to man 🤘
@JasonsFourCamFox9 ай бұрын
Similar situation, I have an 88 Coupe 5.0, that I'm installing a new 347 Stroker also with the Sniper fuel injection as well. I want to clean up as much ECU junk/wires as possible under the hood and have heard anything hooked up to the ECU can come out, but I'm unsure on that? I thought some things on the interior had to stay connected to it? Do you know if this is true or not?
@SFFRACING9 ай бұрын
I'm pretty sure you have to jumper wires in the car at the ecu plug on a fox but I'm not 100 percent
@shanewright69589 ай бұрын
You need to get back to putting out more videos 👍👍
@SFFRACING9 ай бұрын
I'm trying man my life has just been hectic
@lancelemmer64488 ай бұрын
If u take off the injection wiring harness, do you need to wiring for that harness? Great video man 🤘
@SFFRACING8 ай бұрын
@lancelemmer6448 you don't have to have the engine harness but you have to tie into the pins on the body harness if you want the gauges to work its 3 wires out of the whole harness
@lancelemmer64488 ай бұрын
@@SFFRACING do u have any pics on how to do it?
@SFFRACING8 ай бұрын
@@lancelemmer6448 I can send you a link to the website I used to wire it
@aaronmoura12349 ай бұрын
Man yall are all over the fucking place 😂
@ElmerHansen-od7jy9 ай бұрын
🙃 P r o m o S M
@SFFRACING9 ай бұрын
Lol
@jamesgraham392810 ай бұрын
Nice job, I’m looking for a clutch like that do you happen to have a link
@SFFRACING9 ай бұрын
I was just the factory clutch from the golf cart with a 3/4" to 1" adapter welded in
@supradma7110 ай бұрын
Did your 96-98 Legacy Drive shaft bolt right up to the SVX carrier bearing mounting on the chassis? It looks to me like they are very different in shape.
@SFFRACING10 ай бұрын
The svx driveshaft bolted right up I ended up not using the legacy one
@IchliebeHunde5810 ай бұрын
A long bud makes quite a good mover.
@SFFRACING10 ай бұрын
A great mover!
@IchliebeHunde5810 ай бұрын
Happy for ya, mayne. I have a 96 Dodge with the 12 in it and put a mild #11 plate, boost elbow, 4 in straight piped exhaust turbo back, high flow intake elbow, and intake. I love that extra power; more than enough to cruise comfortably up long grades with my 26 ft enclosed trailer with my hot rod inside. Thanks for the video. You don’t see too many people tuning up their school bus 12 valve (like they should) so fun to see.
@SFFRACING10 ай бұрын
Hell yeah man thanks I appreciate that! It made a huge difference
@christianclem657910 ай бұрын
I wonder if he sold the sand rail.
@SFFRACING10 ай бұрын
Yeah he did
@mrgmc631410 ай бұрын
Nice but what is it ??
@SFFRACING10 ай бұрын
New rod for a hydraulic cylinder
@mrgmc631410 ай бұрын
@SFFRACING OK now I see it lol ,,, so are we going to get some booger hook 🪝 vids any time soon ??
@SFFRACING10 ай бұрын
@@mrgmc6314 I just ordered parts to build a new engine for it ....I have been super unmotivated lately lol
@peterjuhlke743710 ай бұрын
Hope the kids didn't get painted , as looks like they were getting overspray and the nieghbours must love you guys too after that ,lol.