😢It's just injectors. Toyotas have sounded like that for years. Totally normal.

thank you for the info.

any update?

Mine sounds exactly the same, noise increases in frequency with revs but is as soft as in neutral. I've watched other guys with it unfortunately some of em say that it turned out to be bad rod bearing.

I'm having the same issue with my SST16. It's been very difficult to find any information on this model. Taking off the mowing deck was different than the other models. However, I'm having a lot of trouble trying to take off the seat platform to get at the actuators. Any advice on how to remove it? Thanks

I get a huge vibration(shuttering) when i accelerate really really slow. If i press the gas normal or hard, it doesn't vibrate at all. I just had my truck looked at from a trusted body shop, to check all the u joints and carrier bearing and they said everything looked good, that there wasn't much play when trying to move it. My truck has 250K miles already on all original ujoints and carrier bearing. I think i'll replace them myself and see if it stop the vibration on super slow acceleration.

Is there an update? Did you find the solution?

Thanks for posting. Very helpful.

Thats the worst i ever seen! Always a little play. But not clanky chunking play

Will this work on a 2015 tacoma?

Great vid however I’d recommend an inline fuse for protection especially if you off road in mud/wet environments. Don’t want any electrical issues as I’ve seen on a few here that used this technique.

Did you ever have your driveshaft balanced at a driveshaft shop? I just had mine Balanced and put new Spicer Joints and a ford ranger carrier bearing in it.Cant wait to see how it drives and how smooth it is now.

Thanks

I'm having a hard time figuring out how you connected to that green wire at the terminal like that, any tips to point me in the right direction?

Awesome

will this work on a 2017 tundra?

2021 43k miles. Clicks away when you first start it. Very noisy engines. Now has 72k miles. Sounds exactly the same. Very normal.

If you open the console, pull the felt up, and pop up the bottom of the acc outlet plastic trim up you have a ton more room to use the wrenches. Great video. All the others out there tell you to take the entire center console off!

You just saved me a lot of trouble. I'll be keeping this in my book of tricks.

Thank you this is the most practical version I have seen and I fought this 3 hours.

I am currently doing this on my Rav4.. Do you have to loosen the top not first though? Can't you just tighten that and have it tighten the bottom one as it moves down? It's hard to move my hands in there with the 10mm wrench so I tried that and got it to now have less clicks when lifting lever.. I'm wondering if that is ok or if I have to loosen the top nut first before adjusting the bottom one

I just ordered this and you may have saved me some aggravation. Thank you

Thank you

Thank you! How do i go about cleaning, greasing, and sealing it back up?

Thank you. Very helpful. I have to remove mine tomorrow. 06 Tacoma. It syarted the day after I was wheeling un deep water and mud, next day it stopped working.

kzbin.info/www/bejne/nnTOkJinm5aqjJosi=SfHiv714Qd86ciC_

Remember to adjust it until it only takes six clicks to be full on.

Btw.. i added seafoam to the oil and gas, it greatly reduced the noise in combination with higgh octane fuel.

I have a 2005 Tacoma. My 4 wheel drive has stopped working. If I flip the switch from 2 WD to 4 WD H (or low) it won’t do anything. Absolutely nothing. But if I turn the truck off, and then while off flip the switch to 4 WD H, and then start the truck… the green 4x4 symbol will light up on the dash, and it appears it is in 4 WD. But it will only do this if I switch to 4WD while the truck is off and then start it. Is this likely the issue you are addressing in this video?

The ultimate question is does it still make that noise 4 years later? My 15 has sounded like this since I got it but it bothers me sometimes.

Would that work on a 06 tundra?

Thanks bro

thanks it's good to know how much play there is on a new carrier bearing, good video..

Thanks to you I fixed my parking brake problem, awesome!!

THANX

THANX

I have this same thing, nothing when cold or drive but when it’s in park or neutral at super low RPM it does it. Crawled under literally coming from the same exact spot as yours, have you or anyone figured out why the hell it’s doing it?

I just did my lite on my 2010 corolla. Your video was 90% of doing it. The only thing I did bad was I cracked the tip off of that long strip to the right. Super glue did a good job. Thanks for the help.

2011 Toyota Tacoma, fog lights fuse keeps burning any idea why? Thanks in advance.

I have the same sound. Just started. Truck runs and drives the same but has this exact sound. You ever get it looked at or did it cause problems?

4Hi worked on mine, 4Lo was blinking. So, took it out soldered the connections and greased the gears. Now I am ready for 4x4! The 12mm bolt on the top passenger side, APIA to remove! 12mm 1/4 socket and ratchet, small hands helped.

Man. your '07 looks awesome.

Thanks for showing block drains. How do you blow out heater core ?

Well it also let you run them with the high beams on

Nice work. Just a heads up tho. Anytime you are talking about right or left on a car it is always as if you are sitting in the seats looking forward. Driver side is left and passenger side is right.

Stoopid 🤦‍♂️

I plan on doing the Exhaust manifold converter. Do you think that’s a good time to do the mount?

I want to set mine by rpm, not by sound... What is the target rpm at wot after the muffler mod? My owner's manual says idle is at 2600-3600, with clutch engaged is 3600-4200 and wot at 11000 to 12500 rpm...does this still apply after the mod???

You just broke it! This is not how it is removed

Verry good