14 күн бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
Пікірлер
@brianberes6564 2 күн бұрын
That mount being swept back is normal
@Jack_77990 12 күн бұрын
Cool👍
@goosesalsa1664 6 ай бұрын
How did you get the shuttle valve out? Thanks!
@speakersteve9586 9 ай бұрын
You rebuild brake proportion valves?
@KennethPetrovic-lp8lv 11 ай бұрын
HOW DO YOU GET THAT PIN UNSTUCK I'M HAVING TROUBLE WITH ONE I ORDERED.
@oldautollc2405 11 ай бұрын
Which pin?
@KennethPetrovic-lp8lv 11 ай бұрын
At 22:27 of the video how did you get the pin to loosen up.
@KennethPetrovic-lp8lv 11 ай бұрын
You said it didn't move now it moves.. taking about the pin. Do you put some lube on it
@KennethPetrovic-lp8lv 11 ай бұрын
I BELIEVE IT'S TO RESET THE PROPORTION VALVE. THE PIN YOU GRABBED WITH THE NEEDLE NOSE PLIERS
@KennethPetrovic-lp8lv 11 ай бұрын
Can you use pb blaster to loosen up that pin.
@KennethPetrovic-lp8lv 11 ай бұрын
WHEN YOU PUT THE HAT IN WITH THE PIECE YOU SAID SHOULD MOVE I ORDERED ONE AND THE PIN IS STUCK WHAT CAN I DO TO GET IT TO MOVE LIKE YOU DID.
@KennethPetrovic-lp8lv 11 ай бұрын
Do you rebuild these if I sent you mine
@oldautollc2405 11 ай бұрын
yes
@KennethPetrovic-lp8lv 11 ай бұрын
What's the address I can ship it to
@oldautollc2405 11 ай бұрын
308 Cambridge Lane Lititz pa 17543
@KennethPetrovic-lp8lv 11 ай бұрын
Is there a number I can call you I have a few questions I'd like to ask you with this new valve I have.
@RichardPrice-s8w Жыл бұрын
Where can I locate the piston cups
@mathew5801 Жыл бұрын
What do you charge to do this?
@oldautollc2405 11 ай бұрын
all depends on valve type
@ronaldrose3633 Жыл бұрын
You didn't show how you removed the 'shuttle' or the brake line seats?! This would help a lot.
@cromaticdragon5079 Жыл бұрын
Thanks for sharing man, will be sending you the valve from my van soon
@autojumbleusa 2 жыл бұрын
Nice work 👏
@SpoonerTuner 2 жыл бұрын
FYI - You should only use o-rings made from Ethylene Propylene Diene Monomer (EPDM) so the brake fluid doesn't damage them.
@oldautollc2405 11 ай бұрын
that is all we use
@mountainanderson5597 2 жыл бұрын
Mine doesn't have the pin on the end, it has a blocked off part, I can't access the metering valve. Any idea how I would go about rebuilding it then?
@journeyquest1 2 жыл бұрын
Machined?
@kevinsharp7646 2 жыл бұрын
Great video! Thanks for the the tips on how to get these proportioning valves apart. I'm struggling to remove the stem. I'll use the grease gun method that was shown. I'm currently working to disassemble a Kelsey-Hayes 86652 Combination Valve. Where do you purchase the replacement parts to rebuild these? What chemical did you use to clean the inside of the valve body to remove any rust/grime, or did you use just plain brake fluid? It appears the exterior was sandblasted? My proportioning valve is almost 50 years old and has never been dissembled. Please share on how you cleaned this valve. Thank you.
@desertmopars3336 2 жыл бұрын
Nice to see someone take on something that many would consider too far gone. These Sweptlines need to be saved!! We have a 70 that we are working on, take a look. We'll be watching for your progress my friend...
@oldautollc2405 2 жыл бұрын
Thank you! I’ll be watching your progress too!
@scottmottazsr3030 2 жыл бұрын
Do you happen to know where to get all the seals and O rings for that proportioning valve. Thanks in advance
@oldautollc2405 2 жыл бұрын
I get special lip seals and the O rings from a couple different places. It just all depends on what they have in stock and you usually have to order a large quantity at one time. You have to know the sizes. No one sells by application.
@RichardPrice-s8w Жыл бұрын
What is source of the piston cups
@odellkercado211 2 жыл бұрын
🌺 Promo`SM!!