3 ай бұрын
4 ай бұрын
4 ай бұрын
Пікірлер
@garethbeale3275 4 күн бұрын
I just did this repair and there is no need to remove the handrail or the base of the console. Just remove the back cover (16 screws) and then disconnect the one connector and ground wire and then all the fasteners on the back of the console. There are three on each side, 2 each top and bottom, and the four bolts on each of the two metal brackets.
@imaginitivity7853 5 күн бұрын
I'm looking for a treadmill and can get a good price on a NordicTrack 1000 but the main motor is reported as faulty. Can the motors generally be serviced or must it be replaced? Are they expensive or are generic options available? Thanks
@rochellebillington1742 6 күн бұрын
how do you lift out the battery compartment? Is there a button to press. Mine separate a little but something is holding it in.
@gitfit875 6 күн бұрын
This one has velcro on the bottom of the battery
@victorescandonphotography 7 күн бұрын
hey brother. how do I do a factory reset. seems ours is on display mode? thanks. nice video
@jamesellette 12 күн бұрын
There is not a button inside mine. At all.
@DanielR-e7o 15 күн бұрын
Just know that you are bringing so much joy to a 8 and 10 year old today when they get home from school. Got a C990 3.0CHP for free. After all the work of getting in the house it did not work. I accidentally deleted the IFIT app but I still followed your instructions and it works. This is after being on the phone with client care for over 1 hour. I cannot believe that they told me it’s discontinued and can’t help me… wow how is that customer service? You are an amazing person for doing this video. Thank you!
@carlmazziotti221 16 күн бұрын
Just bought a used nordictrack today. Everything worked perfectly so i connected to the internet and it updated. Sure enough i toasted the treadmill because i updated it. This video saved me!! Question, if auto update is turned on, will it try to update and liop again? Should i not update ever again?
@gaziislam6422 16 күн бұрын
3:08 hi, thanks for the great video! What is this tool to remove the fans? I bought NordicTrack used and it didn’t come with. If you could share the link, would be great!
@gitfit875 16 күн бұрын
amzn.to/3Tukcvy
@sandyjy235 16 күн бұрын
Very helpful. Once it had some soapy water on it, it slid right on.
@brianc6739 16 күн бұрын
Hose with that black can in it at the 0:37 mark. What is that?
@scoobygaming-or3no 18 күн бұрын
Aren’t you supposed to keep liquids away from the treadmill?
@gitfit875 18 күн бұрын
Definitely don't open the hood and spray that stuff down for sure!
@Michelle_Lawrence 21 күн бұрын
Could you make video how to open it from the beginning and how to put it back?
@gitfit875 21 күн бұрын
Great idea! I'll totally make one
@MoganSlaya 24 күн бұрын
Just wanted to thank you for taking the time and putting these videos up. Several of your videos have saved me time and aggravation. Big learning curve of these types of repairs and you've made it pain free. Hats off brotha!
@candacemartinek5798 Ай бұрын
What is that black filter in the first hose you took off?
@biafan9139 Ай бұрын
Thank you for the video i got the bootloop to stop. The only thing is the buttons are unresponsive to going back or home screen. Maybe the screen just needs replaced?
@gitfit875 Ай бұрын
kzbin.info/www/bejne/qWiaaoaIYtB2odE
@biafan9139 Ай бұрын
@@gitfit875 I will try it out thank you for the info and response. I have the free motion incline trainer i11.9 it's for my work.
@ramkishoremovie Ай бұрын
Thank you very much. I’ve been browsing through many videos but finally found solution in your video. Even though my treadmill is from Pro-Form but the troubleshooting steps are similar.
@NunoCardosoMedeiros Ай бұрын
Hello. I have a Nordictrack e7.2 elliptical which has a this problem. I mede what you sugest in this video, opened the console and cleaned the terminals of the two flat cables and reinserted them into the slot, which worked once, but the second time I try to use the keys they no longer respond. anyone has some idea why is this happening? Note that i've made this procedure more than one time and it's allways the same, works for one time but the next time i try to use it no longer avilable. I should say that i'm very gratefull to "GITGIFT" Thank you very much.
@gitfit875 19 күн бұрын
I've had this happen many times.... you could attempt timing back the ribbon cable about 1/16 inch
@jeromemainmanmanne7496 Ай бұрын
Our Commercial 2450 treadmill belt sides are under the plastic sides so I cannot reach under to lubricate belt and deck. Do I remove the sides or...?
@gitfit875 Ай бұрын
I usually use a flat head screwdriver to retrieve it, however, removing the sides would work too, it's connected with screws on the bottom of the deck
@bugzziee Ай бұрын
Ur too vague
@MartiganBlue Ай бұрын
Thank you! ❤
@ericparsons1625 Ай бұрын
I hope this only takes me 4 minutes as well. Ill let you know...
@guylainechasse3598 Ай бұрын
this was amazing and worked thank you
@xRaixio Ай бұрын
Thanks for the video! Does the backup camera in the review mirror still work?
@gitfit875 Ай бұрын
Totally does!! With the harness, nothing was affected
@ramonzera_oficial9545 Ай бұрын
Os botões de start e stop não funcionam. Alguma idéia pra me ajudar?
@gitfit875 Ай бұрын
kzbin.info/www/bejne/qWiaaoaIYtB2odE
@ramonzera_oficial9545 Ай бұрын
@@gitfit875 MUITO OBRIGADO
@elizabethhuerta1546 Ай бұрын
Hello, can anyone guide me to mounting my sd card back? somehow I unmounted the sd card and i can't mount it back up to be able to proceed with the ifit download
@arollofcukin2452 2 ай бұрын
Thanks for posting this. Helped me determine it was the controller not the motor. Got a new controller on warranty so pretty pumped!
@arollofcukin2452 2 ай бұрын
I ended up taking the control board out, identified that it was a MOSFET that failed and replaced it. This 100% fixed my issue. Very easy solder fix.
@gitfit875 2 ай бұрын
Dude!!! That is awesome!!!
@nester9067 2 ай бұрын
Good video, but the music is REALLY, REALLY annoying.....
@SimsalabimBoom-1 2 ай бұрын
I got to the end of the apk install. It tells me "success...please wait while ifit reboots" then freezes.
@gitfit875 2 ай бұрын
I've had this issue where it takes a few tries sometimes
@cjafx 2 ай бұрын
Our 1750 either slows or stops after a period of time, around 30 minutes or so into a walk or jog. What should I focus on?
@gitfit875 2 ай бұрын
Sounds like friction taking that long to stop. Clean and lubricate the deck. If you feel groves burned into the deck where you walk, then flip the deck, then lubricate it
@cjafx 2 ай бұрын
Thanks! I’ll attempt this weekend.
@gitfit875 2 ай бұрын
Here's the video on flipping the deck if you need to go that route: kzbin.info/www/bejne/gXiko2x4ZbpgatE
@cjafx 2 ай бұрын
@@gitfit875much appreciated!
@cjafx 2 ай бұрын
Deck is good, followed the video entirely, no more issues! However, the dual fans built into the console haven’t worked in quite some time. Any suggestions on what to check?
@jjjohn5914 2 ай бұрын
Exterior is easy......how do you clean the inside of the belt???
@gitfit875 2 ай бұрын
Even easier!! Be sure to lubricate afterwards!! kzbin.infoM4ASPCRHxHM?feature=share
@jjjohn5914 2 ай бұрын
@@gitfit875 thanks....do u have a way to clean the deck too?
@gitfit875 2 ай бұрын
kzbin.info/www/bejne/rnvUZ2msjZl-sKc
@jjjohn5914 2 ай бұрын
@@gitfit875 thank you
@amcalca1 2 ай бұрын
sweet porn music
@oldphart-zc3jz 3 ай бұрын
Good video, no stupid dialogue, just information! BTW a jump pack or jumper cable will power a gate just fine until one gets around to running power. I welded a lifting eye at each end of mine for easy install with an engine hoist. How much you can carry depends on your rear suspension (stock is always soft) so I use Hellwig overload leaves and Timbren urethane springs (they do not conflict) on my F150.
@RobertCouret-k7g 3 ай бұрын
On 2450 Incline works, Speeds stays on #1 setting only. Any thoughts.
@gitfit875 3 ай бұрын
Do the speed buttons respond?
@RobertCouret-k7g 3 ай бұрын
@@gitfit875 No. Only the start button and incline button work. not even the stop button. And thanks for the quick reply.
@gitfit875 3 ай бұрын
@user-ss2lg8zk8o kzbin.info/www/bejne/qWiaaoaIYtB2odE
@RobertCouret-k7g 3 ай бұрын
Thank You. Will follow the method shown in video. Will let you know how it turns out.
@gitfit875 3 ай бұрын
Good luck.! My success rate of cleaning the ribbon cables is about 80 percent. The ends of the cables can be trimmed back 1/16" as well
@fireball4thewin108 3 ай бұрын
Would you be able to make a video explaining the wiring better?
@gitfit875 3 ай бұрын
That is a great idea!!
@benschmaus4976 3 ай бұрын
I was curious what the symptoms could be on a motor that has not quite failed but maybe is on its way out. For example on my 2450 recently if you set the speed to 4.0mph it seems the motor speed might fluctuate slightly slower for some time and then speed back up. Not always but sometimes or in one case to get a 4.0mph pace I needed to have it at 4.8mph. But maybe the incorrect voltage is going to the motor to cause this and maybe the speed sensor is the case.
@gitfit875 3 ай бұрын
Depending on the age, it might not have a speed sensor, yet the speed is still adjustable. If you're getting speed fluctuation, it's most likely an issue with the controller sending erratic voltage to the motor.
@benschmaus4976 3 ай бұрын
@@gitfit875 Its really subtle - like one day it was for a consistent 10 minutes then it returned back to normal speed - then once it was normal speed then slowed for the rest of the duration of use ~40min - I had to up the speed to 4.8mph to get it to go at the 4.0mph pace. Its 4 years old and only has ~950 miles on it.
@Tiffanysalazar1990 3 ай бұрын
I can’t find the pin hole I have a nordictrack 2450 commercial treadmill and the screen is just blank and the fan turns on
@gitfit875 3 ай бұрын
It can be so hard to find on some models!! It's often on the parameter, in the groove where the plastic housing fits together. Tiny! I use a flashlight quite often to locate it.
@papabear8160 3 ай бұрын
It feels like I’m going to snap my bolts when I go counter clockwise. Any ideas why that might be? I don’t want to push too hard
@gitfit875 3 ай бұрын
Which bolts? I don't believe there's anything that's backward threaded. Rear roller bolts tend to rust from sweat, or if the machine is in a garage.
@roymartinez8135 3 ай бұрын
minen turns on the screen but will shit off in inseconds will shut off any suggestion ? I have removed the electrical cover and I do have 120 volts coming in to the circuit board though thank you in advance
@gitfit875 3 ай бұрын
Do you have a volt meter? At the console you should get (I think) 12vdc.
@-Quisp- 3 ай бұрын
I just bought a used ND 1750 Commercial, 22 model I think. When I turn the Cushion Knob on the side, theres no locking/unlocking or movement of the mechanism. Any idea what might be the issue?
@-Quisp- 3 ай бұрын
Nevermind. I just didnt turn the knob enough. It moves fine now.
@ldproc0 4 ай бұрын
How do you reaccess the android menu before it jumps to iFIT menus?
@gitfit875 4 ай бұрын
After using a reprogramming card?
@ldproc0 4 ай бұрын
Yes, correct!
@gitfit875 4 ай бұрын
After it boots up, go to the maintenance page, then with your finger draw > on the top center of the screen
@ldproc0 4 ай бұрын
Thank you!!!
@joncorso6103 4 ай бұрын
Looks very useful for my upcoming replacement, was surprised to see that I couldn't find anything official (maybe I shouldn't be). Thanks.
@couti 4 ай бұрын
Thank you so much, I will donate for a beer :)
@gitfit875 4 ай бұрын
What what!!!!:) www.paypal.com/donate/?hosted_button_id=P6VN3HBLFCZEG
@couti 4 ай бұрын
@@gitfit875 done my friend :)
@popkhajohnveeraphan54 4 ай бұрын
How could remove the coil out of the shaft?
@ENB1968 4 ай бұрын
I have a C2155 model...is there a vid out there that shows how to replace the drive belt on that? It's different from the C2150.
@gitfit875 4 ай бұрын
If I remember right, that one has a bolt on either side of the drive roller. Loosen the rear roller, then back off the two bolts on either end of the drive roller 3 complete turns, but not more than that or you'll have other stuff to deal with.
@ENB1968 4 ай бұрын
@@gitfit875 Okay, great! Will the drive roller slip out once the bolts are loosened or do the bolts need to be taken completely out in order to free the drive roller and slip over the new drive belt?
@gitfit875 4 ай бұрын
It will take a little force pulling it out. If you remove the bolts totally the whole base frame will come off..... just 3 complete turns on the front drive roller bolts..... the rear roller, loosen those bolts 15 complete turns
@ENB1968 4 ай бұрын
@@gitfit875 Just followed your advice and BOOM...back in business! Thank you so much for your insight! It was certainly hard - getting the drive roller out of the slots, then putting them back in to align the chucks. Then came the really tough parts: walking the new belt onto the pulleys then adjusting the belt tensioners so it doesn't pull one way or the other. But somehow my baby is working again with no slippage!
@JohnMazur-e4x 4 ай бұрын
What device did you use to pull the flywheel? Is it something you made or purchased? Thanks
@gitfit875 4 ай бұрын
amzn.to/4dB2AGI
@JohnMazur-e4x 4 ай бұрын
@@gitfit875 Thank you!
@jharris3291 4 ай бұрын
Well definitely didn't miss the unneeded dialogue. I will now Subscribe to see what else you can fix!
@gitfit875 4 ай бұрын
Sweet!!!!
@michaelross4537 4 ай бұрын
Nice video but why did you replace the wheel? Was it noisy
@campingalan 4 ай бұрын
Good afternoon! Thank you for this awesome and informative video. We have some house guests that will be filling up our 136 yr old house in June. When they leave, we will order a 1750 or a 2450. I am sure the answer floats around “it depends”, but how often do you do a lubrication on these machines (2 people using it 2 or 3 times per week)?
@gitfit875 4 ай бұрын
90 hours of use.
@campingalan 4 ай бұрын
@gitfit875 thank you very much for the prompt reply. When we get one, I will buy one of your adjustment wrenches. A follow on question....if we have 2 people using the machine on the family plan for ifit, is there a maintenance page that will show the cumulative usage so as to determine that 90 hr block?
@gitfit875 4 ай бұрын
@@campingalan settings- machine info- equipment info
@user-xe9zc4ng8w 4 ай бұрын
Intro: RIP Headphone users
@gw8390 4 ай бұрын
Where did you get the servo motor from?