Norwesco

Пікірлер

@tuberez 2 ай бұрын

I have the 1000g tank. After a year the first chamber inlet is full of water and overflowing. Help!

@pipe_iran_ir 3 ай бұрын

👏👏👏🤩💯

@mahtab_gostar2 4 ай бұрын

💯🤩👏👏👏

@marthahenson7526 5 ай бұрын

They never checked for leaks before backfilling. The company who sold this tank won't warranty it when we found a leak. They said we backfilled incorrectly. There IS NO BACKFILL IN OUT DITCH!

@nperry77 8 ай бұрын

My pipe is not wanting to go in. Any suggestions?

@user-zt9dr9vr6q 10 ай бұрын

This going to be my biggest headache after u buy my new land. The tank is 2k and the installation could be up to 3k. Seems ridiculous just to be able to take a sht.

@voidisyinyangvoidisyinyang885 7 ай бұрын

try getting a year round composting toilet. 6K and it's essentially the same plastic design - only has oxygen for aerobic bacteria. hahahaha. That's just the price of the composting toilet for year around - as certified by the EPA - but doesn't include installation. Best to build your house around that huge indoor composting toilet - only you need it to stay warm to keep composting. haha

@vasilebrumar4319 11 ай бұрын

.nu vă supărați ce preți are un butoi ce se vede pe tictok si cîte kilograme are vă rog dațim un răspuns sunt interesat de un butoi la așa mărime astept răspuns

@judahcortez5235 11 ай бұрын

Thank uuuuuuu❤

@CasanovaBrown57 Жыл бұрын

Why don't you just buy a concrete tank. You don't have to worry about putting a bed of sand or fill the tank up with water before you backfill. You don't have to worry about the tank collapsing when you pump it out.

@user-zt9dr9vr6q 9 ай бұрын

Too expensive

@TheSteverad 7 ай бұрын

will cost more after the piece of junk plastic tank gets deformed and you have to replace it!@@user-zt9dr9vr6q

@thomasgregory8941 Жыл бұрын

Good. Need a reaching tool

@gm08351 2 жыл бұрын

you didn't tell me a model number, sizing, or where I can get the replacement part.

@Norwesco_Inc 2 жыл бұрын

Thank you for your interest in Norwesco products. There are a variety of sizes and models of bulkhead fittings available. For assistance locating the correct one for your application please check the following directory: www.norwesco.com/products/valves-couplers-accessories/bulkhead-fittings Distributors to purchase from can be located here, or by contacting customer service at: 800-328-3420 www.norwesco.com/search-distributor?search_type=VCA

@Off-Grid 2 жыл бұрын

Here is the video of our dual tank installation. kzbin.info/www/bejne/Y4bYhWOOocR9js0

@jacobalexander7192 2 жыл бұрын

Is there an additional piece I am missing? In the center baffle, is there a cap or filter over the baffling hole? It looks like there is on the product drawing

@kirkandrew7853 Жыл бұрын

For those you should be compacting dirt down in those

@tuberez 2 жыл бұрын

So no pvc glue or pipe compound on the 2 inch hole to 2 inch ball valve?

@daveyt4802 2 жыл бұрын

Can you use anything else to breach the tanks? I needed a pressure fitting so I just drilled and tapped a hole in the side of the tank (1/4" NPT). Wondering about the hole splitting. It's out of the way, need to keep idiots from smashing into it now.

@daveyt4802 2 жыл бұрын

Can you just drill a hole in the tank, thread it and screw a nipple into the side of a tank? Will it split eventually?

@gregh2632 2 жыл бұрын

Where I live, you need to have access to the effluent filter. Why was there only 1 riser installed on the inlet side, and the outlet side where the filter is got burried. That filter needs to be cleaned at least once a year.

@giantoftheeast991 2 жыл бұрын

Also check for lumps of plastic near the seal.

@daveyt4802 2 жыл бұрын

Use deburring tool around the inside of the hole too. Don't put the gasket on the outside!

@DW-ni4xb 2 жыл бұрын

Why do they want to put a graid or on top of tank what water hurt outside of tank which make no sense since there's moisture all around it

@travman2863 2 жыл бұрын

Why not just put bacteria kzbin.info/www/bejne/eoG9haZ9ibFlpKc from the bottom of the ocean or the bacteria from our salty boggy marshes that breakdown and consume organic matter and convert it into electrical current as long as you use a non-conductive septic tank and then put a superconductive coating on a conductive Rod or strip of metal on each end of the septic tank to receive electrical current discharge from bacteria to power your house or charge an EV vehicle.

@therealleonardlewis5438 2 жыл бұрын

Man if that thing ever was to erode look out!

@mylifeinanutshell6931 2 жыл бұрын

They last longer than concrete etc.

@mustafayasmin2994 3 жыл бұрын

indhoda price evlo

@rudybetta 3 жыл бұрын

Shouldn't you fill the tank with water before you backfill to make sure it's settled properly ?

@DriftmanX 3 жыл бұрын

Are rubber seals necessary

@timexkills65 3 жыл бұрын

What about 2 inch to water hose? I can't find a reducer from 2 inch male thread to 1 inch or 3/4

@andydouglass1374 3 жыл бұрын

I thought these tanks needed to be full of water before backfilling.

@texteacher7706 3 жыл бұрын

I noticed that too.

@teammodulbuilds8743 3 жыл бұрын

From their website: No special backfill or water filling required during installation

@Johnnys_World859 3 жыл бұрын

How much pressure will flow

@user-so2rh9om6y 3 жыл бұрын

I figure with a power washer it would be good

@elijahjones8351 Жыл бұрын

You need a water pump

@elijahjones8351 Жыл бұрын

@@user-so2rh9om6y you need a water pump . Gravity flow is eh

@rancelvazquezsanmartin9732 3 жыл бұрын

Which is placed at the end of the outlet pipe? Thanks for the info on the video.

@tuberez 2 ай бұрын

The leech field pipe

@kmmsunil116 4 жыл бұрын

kzbin.info/www/bejne/omKyXnaca76srrs 👈

@yohon8977 4 жыл бұрын

Wasn't using the backhoe bucket a little risky to move that tank around LOL

@jefferywalton8176 2 жыл бұрын

What risk?

@johnreinke3263 5 жыл бұрын

also what kind of reaching tool would i need to replace the bulk head fitting for 1025 gallon and 1625 gallon Horizontal Leg Tanks

@johnreinke3263 5 жыл бұрын

what kind of reaching tool would i need to replace the bulk head fitting for a 1610 (elliptical) drainable leg tank

@uniquesingh7604 5 жыл бұрын

Sir hamko septic tank Ka filtertion chaiye

@iwanstoryofficial 5 жыл бұрын

Very goog, please visit also my vlog click here kzbin.info/www/bejne/eWPYqqOggbNmnsk thank you.

@Nw2381w 5 жыл бұрын

Where do I get one of those "reaching tools"!?

@johnreinke3263 5 жыл бұрын

did they ever tell what brand of reaching tool they used

@daveyt4802 2 жыл бұрын

I work where you make your own. I'd use a steel rod and slide the bulkhead down the rod through the hole from the top cover hole.

@matthewtE Жыл бұрын

Buy some stiff safety wire, bend it, and guide it down inside through the top tank hole. Then, slip on the ring fitting (with some glue on the edges) and jiggle it all the way down. Pull the thin part of the fitting on through the opening and use a long-ass stick to firmly press it against the tank hole. Screw the fitting nut on the outside, tighten it, and let the glue/adhesive dry. Then seal it, so it doesn't leak any water.

@analarmingnumberofbees4571 6 жыл бұрын

Hey can you guys do a tutorial on how to install one of your spherical wastewater tanks?

@Norwesco_Inc 6 жыл бұрын

Thank you for inquiring. It's not something we planed on doing, but it's certainly something we'll consider.

@MushtaqAhmad-jg3bn 8 жыл бұрын

thanks so much

Ең жақсы KZbin

Пікірлер