Simon Kuskye

Пікірлер

@schneekoppe32 43 минут бұрын

Hi, thank you very much for the video. I have the device for a few days and my question/problem is that the device would not automatically connect to the car when the car is turned on (MG4). The device lights up but I need to unplug the USB connector and plug it in again to get it connected to the car. Have you had this problem ? It might well be that it is an issue with the car but I just wanted to ask you for your experience. Thanks !

@NomisRC 39 минут бұрын

I have not seen that issue, sorry. I agree it may not like the car.

@schneekoppe32 30 минут бұрын

@@NomisRCThank you very much for your prompt reply. Other than that the device works perfectly fine. It is not a deal breaker but it would be nicer if the device would connect automatically. Thanks again !

@Nothing_Nothing485 2 күн бұрын

Not hating but ,doesn’t always work when it does work Bluetooth drops out and can’t reboot unless you stop start engine .just saying

@MikeWelch-zc4xw 2 күн бұрын

A WILE BACK YOU WHERE OFFERING SOME ADVISE. I HAVE A VELOCITY OUTRAGE 50 ITS A NITRO 600 SIZE HELI I HAVE A AR7100 AND BEASTX 4.4. RADIO TX16S, I CANT FOR THE LIFE OF ME FIGURE OUT HOW I HAD IT BEFORE THE CRASH BUT IM PULLING A HUGE BLANK. I HAD IT ALL NOTED DOWN BUT I LOST MY SHOP BURNT EVERYTHING I OWN. SO IM TRYING TO PULL MY SELF OUT OF THIS HOLE BY MESSING WITH THESE HELI BUT DONT KNOW IF IT HELP OR MAKING IT WORSE. I HAVE ON BOARD GLOW AND A CARB SMART ALSO ANY HELP WOULD BE GREAT

@tonymartinez6974 4 күн бұрын

Thank you I was raging last night looks like I missed a step smh lol

@NomisRC 2 күн бұрын

@user-rm2bi8xq8t 13 күн бұрын

I have UMX Air tractor, and the source only goes to ch4. Is there something else I can use?

@duddin12390 14 күн бұрын

Any increased wind noise or rattle with the rear spoiler?

@NomisRC 14 күн бұрын

No sir and it's been on a while now.

@richdabarber 18 күн бұрын

Will this work with t28 Trojan 1.1

@NomisRC 18 күн бұрын

if it has an ar636 and you are using an opentx radio yes. As for binding most newer spektrums have a button on them now.

@chocolatethunder2 18 күн бұрын

How exactly did you install the remote wire to the tail light ?

@NomisRC 18 күн бұрын

@5:20 - "the bottom left pin in the rear passenger taillight wire harness" I stripped the wire back some and soldered the remote wire directly to it, then covered it in liquid electrical tape.

@chocolatethunder2 17 күн бұрын

@@NomisRC thank you so much!Got your setup for my 2011 4.6. Super excited

@NomisRC 17 күн бұрын

@@chocolatethunder2 - Awesome man!!

@johnbess7320 20 күн бұрын

Working on the 380 or 420.

@NomisRC 20 күн бұрын

This was a 380 build, but the only thing different on a 420 is longer boom/belt/blades. The rest is identical.

@johnbess7320 20 күн бұрын

@@NomisRC nice build I enjoy your vids

@NomisRC 20 күн бұрын

@@johnbess7320 Thanks!!

@For-get-me-notsAndRoses 21 күн бұрын

How sweet and cute!

@mjmarvel81 22 күн бұрын

I want one. Butterflies are my thing AND I just told my husband tonight that I need a jewelry holder. Ok. Now how much? 😂

@johnbess7320 24 күн бұрын

So your opinion you think the demon is same quality as Goblin?

@NomisRC 24 күн бұрын

Yes the 380/420 devil's are as good as 380/420 goblins. The 500 devil however i would not rate as good as a 570 SAB Goblin.

@johnbess7320 24 күн бұрын

@@NomisRC Ty sir.

@johnbess7320 24 күн бұрын

Devil sorry darn auto spell.

@NomisRC 24 күн бұрын

@@johnbess7320 np

@mustafanot1584 28 күн бұрын

I have issue with when iam playing youtube it stopts the video after few seconde why is this please help me

@NomisRC 28 күн бұрын

I use my phones hotspot, so it is determined by my phones speed. I have 5g att unlimited. I've not had this happen. Please tell me how you use the device, i.e. Android auto or hotspot? Have you done all the updates?

@trycilly788 28 күн бұрын

Really nice Video on how to get your model ready to paint. Have you ever sanded down a piece and polished it after? I just got my self some nice looking pla and I wanted to know what polishing compound works best for some pla models. Can you reccomend any that worked for you and your models?

@arthurdemeurie9676 29 күн бұрын

Hey man! love your project!! do you think it would be possible to have a .step file of that blower?

@brucecampbellx Ай бұрын

beautiful home. 👍

@Hyperslayer12 Ай бұрын

please don't touch the build plate, the oil on your hands are what stop it from sticking well in the future

@NomisRC Ай бұрын

Incorrect, it doesn't matter if you use hairspray and glass or smooth steel sheets, or a pei spring textured sheet. Touching the build plate does not cause adhesion issues. Throughout my 5 years of 3d printing I touch my sheets all the time and have 0 issues with things sticking, I do 30 hour prints all the time and have printed entire suits of armor and many many helmets. Let me give you the advise haha, if you have adhesion issues it's 99% of the time bed leveling issues.

@Hyperslayer12 Ай бұрын

@@NomisRC it’s literally proven the oil from your skin lowers the adhesion of the build plate because filament isn’t made to adhere to your hands oil but it’s meant to stick to the coating that is over the build plates, i don’t know how you didn’t know this after 5 years

@NomisRC Ай бұрын

@@Hyperslayer12 Cool but my point is it's a non issue and a pointless remark. And yes I've heard people worry about it before and me and the rest of the world said the same thing, don't worry about it. I have proven it over and over, and in this video. It doesn't matter.

@atamargo99 Ай бұрын

Hi Simon, thanks for your videos all are the best and easy for apply for me. You use these configuration for Spirit?

@NomisRC Ай бұрын

Yes

@atamargo99 Ай бұрын

@@NomisRC i just State with Micro Sporting and blade 230 and later Strategy with tb40. Thanks a lot for your answer

@atamargo99 Ай бұрын

yes i do it!! thanks again

@thatsmyrc Ай бұрын

This was very helpful thanks for sharing 👍🏼

@mickeyoncrack9127 Ай бұрын

no rush but when is the iron man helmet asembly releasing

@sirsirajvlogs9300 Ай бұрын

so huge to clean up hehek

@sirsirajvlogs9300 Ай бұрын

wow...love it sis...enjoy searching together...wait for me there as your first visitor in your new home...hehek

@DookieShoes772 Ай бұрын

You just rubbed it on. No other steps? Does it not come off if you touch it? It looks amazing

@NomisRC Ай бұрын

Yes it does come off if you buff it with a rag and your hand "rubbing mildly hard", but not super easily, and can be applied again easy.

@DookieShoes772 Ай бұрын

Thanks for advice, just tried it out and it worked like a charm

@NomisRC Ай бұрын

@@DookieShoes772 Awesome man, I was surprised how easy it was, im sold on it haha.

@jasimal-ajmi4444 Ай бұрын

Can I shared Google map location directly by airdrop | bt ?

@omaralvarado1080 Ай бұрын

Exciting I am waiting for mine to come at 10 today. 😊

@NomisRC Ай бұрын

Sweet!!!

@mattmaurizi2069 Ай бұрын

What did you do with the ambient lighting around the doors and speakers look way better with that

@GerardoSantanaGL Ай бұрын

How did you do the post processing? What paint did you use?

@NomisRC Ай бұрын

This is my video on post processing, kzbin.info/www/bejne/oHKQaK1jqqipj5Y

@lisafulmer8530 Ай бұрын

How do u make it so smooth I wanna do that to my infraction v2

@NomisRC Ай бұрын

Its a sensored motor/esc. Any sensored motor is that smooth. This particular one is a Hobbywing Max5 250amp and 56118sd motor fully sensored system.

@BigKidsRC Ай бұрын

Hi New sub here I just bought this whole system for my XMAXX I have 25/30 1.5 mod gearing and I burned up my first max 5 but the esc was used kinda smelled burnt out of the box and I paired it with a 5687 11kv HW motor got 3 runs out of it so I bought this same system how do you like it?

@NomisRC Ай бұрын

I have two of these g2 800kv 250amp systems, they are the best combos I've never had, I have beat the crap outta them both. To see a hobby wing go out is rare, I'd say it was a fluke.

@patricksjvdriel5397 Ай бұрын

Hi Simon, at around 11 minutes you are talking about gyro and the rescue switch. Also about stabilization. I cant seem to get my head around it how to set it up correctly. Can you explain please? How to set it in the transmitter and in the software?

@NomisRC Ай бұрын

Transmitter here, kzbin.info/www/bejne/faPJZYx5nMuLrJo Stabi mode and Rudder gain here @8:24, Provided you are using my profile on your TX16, kzbin.info/www/bejne/lXaypXuqfbKehtE If you are running my profile on your TX16 this is the switch assignments, kzbin.info/www/bejne/rZCtYqRroMyWsKc

@superfarful Ай бұрын

hell yeah dude 🤙🏾

@buschauffeuralex Ай бұрын

man this is awesome, thanks!

@NomisRC Ай бұрын

My Spooling System: www.thingiverse.com/thing:6542229

@mssnhllss Ай бұрын

i wish my limited had fog lights

@NomisRC Ай бұрын

If you add this light bar that I have its literally as good as fog lights. When I shut all my lights off it hits the ground right in front of the car and I can even drive in pitch black with only it on. Page 5 Post #65 www.ioniqforum.com/threads/customizing-playing-w-ioniq-5-lots-of-aftermarket-stuff.46094/page-4 Currently all mods: kzbin.infoi62cAgDqjE0

@micron3268 Ай бұрын

Nice build!👍

@NomisRC Ай бұрын

Thank you sir!!

@jonathanwolfe5609 Ай бұрын

I want one

@NomisRC Ай бұрын

Yeah I love it... www.thingiverse.com/thing:2368585

@genises200 Ай бұрын

Man so new to this. Idk how much support is needed and with hight error i kepe getting kn bambu is what I've been using

@xXKP1979Xx Ай бұрын

This is awesome. I saw this on thingaverse but wasnt able to comment, how do you get the bracers on and able to stay on? Side note the canon moving with your head is freakin epic!

@brucecampbellx Ай бұрын

now you just need a Hattori Hanzo sword. 🤘🤘

@NomisRC Ай бұрын

ikr

@user-du4jp9tj2z Ай бұрын

what wing?

@atamargo99 Ай бұрын

Great video!! i just start with Spirit with mal helicopter that your big one, Wich model os spektrum satelite do you use? Thanks in Advance

@NomisRC Ай бұрын

I use both of these below. LemonRX are great "my fav" graysonhobby.com/lemonrx-gen2-satellite-dmsx-campatible.html Or Original Spektrum www.ebay.com/itm/355533333616?itmmeta=01HSCG6P7A3EBG1M5J2SPCJC79&hash=item52c7702470:g:ETYAAOSwljRl7mmk&itmprp=enc%3AAQAJAAAA4DSPjLAYWS%2B1XUUxBehPygS0pC6%2FL5wkJtWQWcqeiJNhb9qPVn9ijHGQnGsqw0%2BeNqeT6vkBS%2BsupRXTnZ904ED%2B0qUoGZYBxmxgJqs6caukLcasadHkhqHVoG8jUn441aCp8V8sc16xqKDEOCuhF0TUczNIFpMKRumNmmOpNQGcwCFSyA2Q2gU0MkOW2KVX%2F2d7miSmZKpy%2ButcQYz%2FcAiqOyGT3AJ0J5a8PWV1daGjw9XQ0YxSIkipHfXqm6Twlvt%2BW7XpjhJeVQ7wMcyI6nc2nuV%2FOfJLguc%2BnV%2F4LIRV%7Ctkp%3ABk9SR_7jmpDLYw

@atamargo99 Ай бұрын

Thanks! I'll use@@NomisRC