DieselGaloreFam

Пікірлер

@smzemperfi Күн бұрын

My cap and housing cracked. And I used a torque wrench to tighten it to spec. So I’m trying to find a good replacement that’s not plastic. :-(

@ericdalton6316 2 ай бұрын

Looks like it isn't tight enough I see a gap

@jr-twomg7839 5 ай бұрын

Ouch

@ethanhuntsman4221 6 ай бұрын

Old o ring is still on it mine did it

@rickvail8608 7 ай бұрын

Bad o ring

@claudiot8431 8 ай бұрын

Oil the o ring and run a pick along it so it sits good in its place.

@seanmcintyre5148 8 ай бұрын

Bad seal

@tylerfisher5150 10 ай бұрын

Check the o-ring.

@duckhunt1058 10 ай бұрын

Just had this problem this past Monday. It was my o-ring and I have similar mileage on my Ram as well.

@jamessmith2157 11 ай бұрын

If it’s from the top of the filter housing it is likely an O ring issue if it’s coming from the lower area of housing it’s likely your drain pitcock assembly

@871jamie Жыл бұрын

The reservoir has a floating magnet in it, that magnet is what completes the circuit via a magnetic field around the sensor when it’s in the proper position. The sensor goes up inside a plastic tube built into the reservoir and is kept separate from the coolant so it isn’t exposed to the coolant. The magnet has a hole in the center of it like a donut and goes around the plastic tube and moves up and down in accordance with the coolant level. Hope that makes sense.

@julioramos2965 Жыл бұрын

Had this problem. My old o ring was inside and I put a new one on and it wasn’t closed right 😅 figured it out after 4 tries.

@mgiffee6816 Жыл бұрын

Not tightened down enough

@mgiffee6816 Жыл бұрын

I just broke my cap....whole lot of fun

@RussellMKay Жыл бұрын

Yep, mine went at 17,250 miles.

@mariovillagomez2213 Жыл бұрын

I bought an aluminum cap for mine. Much easier to screw in and out.

@MatthewWallace-ng8fl 10 ай бұрын

What brand?

@jet0577 Жыл бұрын

No but the elbow behind it to the fuel line is leaking. Anyone know how to replace or the name?

@JustWilderness 2 ай бұрын

Happened to mine too

@JustWilderness 2 ай бұрын

What was the fix?

@jonvill2898 Жыл бұрын

I’m having this problem to

@saltyexxer8253 Жыл бұрын

O ring

@jameshall9147 Жыл бұрын

Ring is pinched buddy

@AngelRodriguez-ml7rh Жыл бұрын

Happened to me a couple times. Brand new O ring did nit seal correctly and I had to keep the old one. Hope your issue is that simple.

@tycompton814 Жыл бұрын

Mine just started doing this as well. 2014 127k

@mrtwister3150 Жыл бұрын

Use motor oil on the threads and o ring before putting the cap on. The oil lubricates the treads and ring to help it seal and spin on better

@thatdroneguy8264 Жыл бұрын

Do not use oil use diesel maybe lol

@hatersaywhat8986 2 жыл бұрын

O ring sits n the bottom of the bowl threads not the cap. When I first did mine it had the same issue and found out the o ring doesn’t go into that slot on the cap. It actually sits on the bowl at the bottom of threads

@DieselGaloreFam 2 жыл бұрын

I had the o ring setting there and when I pulled it off to look at it...it looked fine but I need put a new one on but I did find that the o ring at the bottom of the filter wasn't on the filter but I dont c that causing it too leak

@gangshitsac4166 2 жыл бұрын

@@DieselGaloreFam did u figure out the problem? Mine just started leaking, thanks for your time.

@DieselGaloreFam 2 жыл бұрын

@@gangshitsac4166 the only thing I could see was that the threads on the unit and the cap both were messed up a little but I would think that the o-ring would have still sealed it up

Ең жақсы KZbin

Пікірлер