For really heavily rusted steel rims (say you live in New England) that has been neglected for years, I found it much more efficient to start with a screw driver/chisel/back of a hammer to knock loose and scrape off large chunks of road grime, dust, and chipping old paint. Then follow with a hand steel wire brush. Then coarse sand papers (80 grit). Leave rotary wire brush to the end because it can’t do much in heavy lifting.
@robertlane35133 ай бұрын
Aluminum spray i thought they were steel wheels,
@suatkaya80913 ай бұрын
🚕😎
@Phoebeandfriends-dg2hl3 ай бұрын
Amazing 🤩
@supervitz71785 ай бұрын
Great video. This is how I'd do it if I was just tarting it up to sell the vehicle. But I just did this on an old car that I'm slowly restoring, I did a few things better. 1. When masking, deflate the tyre so you can get the tape slightly under the bead. (If you're not removing the tyre) 2. Use zinc or etch primer first on bare metal before filler primer. 3. After filler primer, always sand it smooth using 1000 grit paper. And do multiple coats until its perfectly smooth. 4. Do multiple coats of colour, and follow up with 1-2 coats of clear gloss lacquer. This improves the shine and durability of the finish. 5. Do both sides of the wheel, and if possible, remove the tyres. I've done this before and without tyres/weights/valve, it's easier to hang the wheel from something and spray all the sides and inside the wheel in one hit. Plus, in theory you're removing/adding weight to the wheel so it should be balanced again for perfection. (Although I've done it both ways depending on the situation). Make sure you clean off the mating surface or mask it up, otherwise you need to retorque the wheel every 50 miles for a while, or remove and refit it a few times. I've had wheels come loose after being repainted because of paint on the hub flange of the wheel.
@Tyrekickingwetdreamer10 ай бұрын
Synthwave❤❤❤❤
@ShakespeareCafe11 ай бұрын
You did your van proud...I have the same design wheels on my Ram Promaster
@frankiebye Жыл бұрын
Brilliant job
@EcoVapdk Жыл бұрын
Nice job 👍 Could u please tell us the name of the products you use to clean
@BASE_Automotive Жыл бұрын
WIRE WHEELS ARE BEST
@staffyboystoney2016 Жыл бұрын
looked up that primer, recommends 24hr drying time WTF surely not needed,how long did you leave b4 painting
@beorlingo Жыл бұрын
I like how the baby starts yearning for milk hearing this song!
@paulaur Жыл бұрын
And how do the wheels look now? 2 years later ;)
@lazyreefer8749 Жыл бұрын
Actually quit like the primer colour.. 🤣
@JustinInMotion2 жыл бұрын
Have a link to the wire brush wheels?
@AhKuang_YT2 жыл бұрын
你這圖一定是用影片製作了檢舉你活該
@daciaduster9852 жыл бұрын
Very Good Renault Kangoo
@quentingirard58422 жыл бұрын
how do you remove the seat slider ?
@subaruadventures2 жыл бұрын
i would have just gotten them powder coated.
@seymourskinner25332 жыл бұрын
Nobody asked
@kayeninetwo35852 жыл бұрын
YAY! MORE ELECTRONIC DANCE MUSIC WHEEL REFURBISHMENT VIDEOS!!!
@deranocasper2 жыл бұрын
Class job on a very dirty van don't think i have seen one as bad whats the attachment you have on your drill when you where cleaning the seats also the brush you used and the pump spray guns any links where i can purchased cheers Van turned out top job keeper suckin diesel 🍻🍻
@user-si9xw6ir5m2 жыл бұрын
Nice work!
@MP-mt8lc3 жыл бұрын
What is the name of the cleaning fluid
@shaggybreeks3 жыл бұрын
Fucking pounding DISCO BEAT!!! Two seconds later, and fuck you, I'm gone.
@gfysyoutube3 жыл бұрын
Nice job. How many cans of paint did you use?
@tonygallo85703 жыл бұрын
Nice job but I would have taken the wheel weights off I would have taken the dents out of the rim that are around the edge and then maybe even replaced the valves so they're new other than that did a fine job
@g.l.obloja62052 жыл бұрын
Kjhövk
@chrisst89223 жыл бұрын
Don't bother masking just smear washing up liquid over the tyre and wash off afterwards.
@MagnusRender3 жыл бұрын
How much does a detailing like this cost to do?
@jamesdecross10353 жыл бұрын
MUSIC"S A BIT LOUD, MATE!!!!!
@user-sy5sj2yq2x3 жыл бұрын
LOWER DOWN YOUR VOLUME MATE!!!!
@Paris.Kalachnikov3 жыл бұрын
Well done
@hubertpehrsson77973 жыл бұрын
Hard work but nice result. Kangoo from year? Do newer Kangoo also have the srews from under?
@danyosan33 жыл бұрын
This is a 2005 I'm sure. Newer kangoos have seats bolted from the inside unlike older models
@AbayomiShobowale3 жыл бұрын
@@danyosan3 do you do this for a living ? If yes how can one contact you? Thanks in advance
@ritchiemeza3 жыл бұрын
I liked the yellow -_-
@danyosan33 жыл бұрын
Me too!!! 🤪
@hiblahablahubla2 жыл бұрын
So did i. More french
@garymartin5573 жыл бұрын
fine job, looks 100x better.
@adamsmith67514 жыл бұрын
The wire brush bit will be alright on a drill, rather than a grinder won't it? Good video :)
@danyosan34 жыл бұрын
It will! Only, I find that the grinder is less harsh on the wrists and is a much quicker process altogether. The choice is yours though!
@adamdenver80193 жыл бұрын
instablaster
@atokhot22094 жыл бұрын
Great job !
@welshsaint35844 жыл бұрын
For those who are not welsh a minger is somthing or someone that is disgusting and dirty.