Richard

Пікірлер

@VernonPerdue 5 ай бұрын

Nice Job. I,m sure you are aware that you have over powered the boat with the 6 hp motor. They are only rated for no more than a 3.5 hp motor. I would check your local laws on HP ratings so you don't get into trouble.

@MrSTOUT73 5 ай бұрын

If you think THIS is tricked out, go check out "Craftsman on the Lake".

@glenpryor288 6 ай бұрын

What is your floor made of Indiana raider owner

@jimmywallhanger8402 10 ай бұрын

garbage

@magicsam84 2 жыл бұрын

Nice clean setup! I love these pelican bass boats 👍

@Cavanpikefishing 2 жыл бұрын

Can't get them in Ireland ider

@Cavanpikefishing 2 жыл бұрын

Great boat

@emperialmusicgroup 2 жыл бұрын

Nice mods , very clean and organized

@ontargetthomunclesam3926 2 жыл бұрын

You are absolutely correct other guy and their ideas about putting 150 lbs. Of B.S on a ten foot boat wow unbelievable it's all about the KISS keep it simple stupid I can certainly appreciate what you have done as far as maintaining room remarkable job yours is one of the top videos on KZbin the only difference in mine is the rod holders are on the inside above the floor

@aravilla5733 2 жыл бұрын

I miss you baby...i won't be tired watching and listening to you...hearing your voice gives me comfort and all memories we had will never forgotten..i love you and i will always will

@billyhurley6866 2 жыл бұрын

I like your rod holder 😉

@kerrywages9631 2 жыл бұрын

Nice Mods...Did you use well nuts for the cleats you installed or do you think screws w/ adhesive are adequate?

@randylane8035 2 жыл бұрын

Very nice. How did you create the front tray for the rods with the half moon pieces of PVC, and did you Velcro all the PVC pieces down, or did you have to use screws any place. I'm just leary of how well screws will hold after some use. Thanks

@stevenvalenti3722 2 жыл бұрын

Wow! I have to say I've looked at alot of videos on KZbin with this boat. All because I'm thinking about getting one also. And your setup is definitely one of the best setups I've seen. Great job sir.🙂🎣

@martinmullins280 2 жыл бұрын

What type of seats?? I really like the set up love the rod holders very nice great job 👏

@panhandlepilot9363 2 жыл бұрын

Can I ask how the seats dont blow out on the road? Very nicely done

@RkRk-xy9fx 2 жыл бұрын

Wow! Love the organization/engineering! Love the rod storage/staggering and keeping one side open. Smart. How do you like the trolling motor mounting system? Hope you do more videos! Thanks.

@bradleywall9089 2 жыл бұрын

id love to see more detail on how you mounted the trolling motor!

@lbs_vevo4192 2 жыл бұрын

your a loser

@gbipit1 2 жыл бұрын

Awesome

@jamesbeal8934 2 жыл бұрын

THIS video is over 5 yrs old but i noticed that boat is only rated at 3.5 hp. wonder if he ever had problems with transom vibration..others have stated there is transom flexing on this boat..

@davidcopple8071 3 жыл бұрын

You could add head and deck lights for night fishing

@PandY7190 3 жыл бұрын

40 people are jealous

@avan2620 3 жыл бұрын

Are the trailer bunks underneath the pontoons? Or in the center in between the pontoons? I set my trailer up and am trying to figure out which way would be best

@richard3423 3 жыл бұрын

Hello, sorry im not on here much now days. I positioned the bunks on pontoons (inboard of the center ridge. Then set the side bunk / guides as close as possible and she will load good every time. Good luck and tight lines!

@kerrywages9631 3 жыл бұрын

Beautiful job ! I just picked up a Mercury 3.5 hp and should probably get a motor support or transom mount...It looks like the motor is fully vertical with transom mount. What brand did you go with?

@sapbtc05 3 жыл бұрын

What did you use to mount the plastic half pvc rod tip holders? It’s a block and is it plastic or wood?

@richard3423 3 жыл бұрын

use coarse wood screws and dont drill. Firm hand pressure on screwdrive and screws will go right in. Do not over tighten scresw. wooden trim

@josephhence9292 3 жыл бұрын

What did you use to mount the foot control motor on the side? Did you have to shim it?

@reelworshipoutdoors2265 3 жыл бұрын

Very nice man

@lnash2569 3 жыл бұрын

Way to much HP on the motor

@terrywilsonjr7870 3 жыл бұрын

This is a nice set-up I have the same identical boat. Please share with us how you have your Trolling Motor mounted and secured to the boat

@catherinefraser8403 3 жыл бұрын

really good setup i run the same motor on mines and i love it next is a trailer

@fishingismydrug1 3 жыл бұрын

Very nice sir! How did you mount the trolling motor? Toggles? Rivnuts?

@B.A.Bassangler 3 жыл бұрын

Working on my new Raider 10e. I also like a stowed trolling motor that doesn't take up any deck space. Did you just shim up the area under the frontmost part of the mounting plate. Hard to zoom in, looks like something in the divot above the handle. What connectors to mount the plate? In hindsight would you do anything different? Thanks for any help you have to offer.

@haroldbaum4398 3 жыл бұрын

Looks good I would bet your over weight

@ronbennettoutdoorswildlife1514 3 жыл бұрын

I see this was posted 2016. Are you still happy with boat? Thinking about getting one. Is it just as or more stable than 12' Alum Jon boat? Seats look comfortable. Where did you get them? Thanks for sharing.

@gaboysoutdoorstv9879 3 жыл бұрын

im 17 and bought one for my first boat i have been in many small boats but this boat is one of the best me and my brother both have plenty of room and it is really stable for a small boat