Why nothing about VSR 400?

Insanely many errors on Systemair home ventilation. The normal lifespan of ventilation units is 15-20 years. My SAVE 300 VTR from 2017 has had the rotor motor changed twice, both fans have been changed and today I have a faulty circuit board. Will never buy Systemair products again.

Boston cream

Thank you! My unit started to make lots of noise after 3 years of use, nobody (even manufacturer) said something could be done except replacing the fans (>500EUR), now it cost me 8EUR in bearings (and 20EUR for the tool to extract them properly). Bearings used: 608zz. Quite so far, hopefully it stays that way.

can it be opened and operated from both sides?

can it be opened and operated from both sides?

This is the old version of the Save Connect module.

why are these so bloody complicated? All we need is a simple fan that works quietly?!

Where did u get the new star lock washers have u a part number please? Many people asking thanks.

Har en sån system men kan inte styra den via appen . Vad behöver man ha för att kunna styra den via appen .

Hur byter man hjullagret som sitter i fläkten, mitt har skurit efter 5,5år?

Which is this pulling tool shaped like a T?

Where did u get the new spring washers for the bearing and circlip? Thanks in advance.

How can we apply for internships or job in Systemair ???

Great video! Does anyone know what is the part number for the starlock washer?

thanks for video, I opened my fan new one costs 495+vat, but 2 bearing like... nothing

The unit never finishes the update. HMI2 and MB3 stays at 0%

This just saved me €300, very usefull tip! Thanks!

Hello. Why did You replace this two washers?

I have done this before

Hello. I have a MAICO ws 170 device. I installed it in 2013, the device has the same fans as in your video. After five years in 2018 the bearings became loud and after replacing the fans they did not work normally, they were spinning but with reduced power. Then I bought new original fans and connected them, which worked normally. Now the bearings were loud again, they wore out again, and today I replaced them again myself, the same thing happened as when I first replaced them five years ago. Please advise what I did wrong?

Qq

Nr 1

Bagaimana saya bisa mendapatkan softwsre ini

Thank you, replacement motor is really expensive and this was quite an easy fix. But what causes the bearing to lock up? There was some dirt inside of it, while the seal looked good. My system is only 5 years old and usually is set to the lowest setting. Just to confirm the other posts: FKS 608-2RSH is an exact replacement. Only cost me 16 Euro's for 1 motor instead of 360 to replace it. My system is a ComAir HRUC-e3

So you ENABLE the moisture transfers setting to REDUCE moisture transfer, which in turn tries to reduce indoor humidity. Very confusing and can be worded much better. Also, what do the P-Band and I-Time settings mean in the MOISTURE TRANSFER CONTROL menu?

How do you clean it?

Die Erklärung ist nichtssagend und wahrscheinlich falsch. Wie funkt. die Feuchtigkeitskontrolle wirklich? Wie funktioniert sie wenn es draussen wärmer ist und wie wenn es draussen kälter ist ??

I'm one of your employees. But not from system im afraid 😟 kzbin.info/www/bejne/q6fTYaqpqKl9nqM

Would be helpful to see an instruction on which way the filter needs to be installed (air flow direction)

Could you provide me with that standard?

Really poor video. 😢

Ty man, the company only offered me a 400€ total replacement while at the end i spent only 10€ in ball bearings 🤣

Where can i buy the bearings set for Ebmpapst fan type: R3G190-RG19-35 and R3G190-RG19-27

Never been this easy to select AHU. Every calculation is doing automatically. SystemairCAD developers are doing great. Thank you from Mongolia.

For me it is fine until second 46. The inside unit is completely stuck inside the outer unit. I cannot even get it out for 3mm

nice

Could someone tell me, what kind of 2 rings the videomaker replaced beneath the 2nd bearer? Thanks in advance

Very useful!!! I fixed two fans on SystemAir SAVE VTR 150. Couldn't find exact SKF bearing model to buy (most likely they changed numbering), but easy available alternative was 608-2RSH. Bearing extractor tool is optional, at least in my case they weren't stuck hard - I used random string to pull it out. A right to repair rules! Thank you very much for this video. Saved me at least 50€ and burden of waiting. I'm not too experienced, so really possible for average person.

please do you have the video for disassmebly embpapst 6318

Thanks for the video! Really cheap and easy way to fix a fan instead of expensive service, managed to do on my VTC 200

Hi , very nice video do you have any experience with EBM fan RG128/1300 ? Bearing on this motor is very noisy .I dont know how I can remove the fan wheel , no screw , no ring ... I dare not just pull the plastic wheel

Hva skjer nor det går hull i plastikken runt aluminiums ventilasjon flexsirørene som er perforerte fulle av hull trekker da ikke damp vann fett gjenom hullene i aliminiumsrørene perforerte av hull som da liksom skal vere lydfelle hvorfor har dere masse hull i ventilasjonsrørene da og hva skjer med os fra dusjing matlaging på kjøkkenet legger da alt fette seg da i isolasjonen runt de perforerte rørene og hvor mange gølvåser har du låv og borre hull i for ventilasjonda er jo betekonstruksjonen alerede svekket eller hva skjer da om du lager da. Hull u masse gulvbjelker hva blir da nyttelasten på gulvene?kann gulvet knekke rase ned for de som flytter inn kann jo fireksempel kjøpe seg en vannseng og en vannseng går det jo mange hundre liter vann inni og så knekker selve gulvet for det er borret hull rett gjennom etaseskillerene?hvem sit ansvar blir det da i en forsikringssak. Dltsfellesak mensker dør for atte alt formye hull i nerende konstruksjoner som gulv vilket forsikringsselskap dekker slike ting de som kjøper huset vet jo ikke vordan det er laget inni det de ikke selve kann se?

Hello. Do u know what bearing number should i buy for R3G190-RG19-21 motor? Please help me

Fantastic Update. Congratulations...

Thank you. good update!

it looks that 3 bearings were removed, but only 2 went back in... video did not show installation of the bearing that '3 leg pull tool' was used for removal...