Machine cannot sew backward. Turn directional wings half around and sew the other way 3 or 4 stiches to end the run.
@manusholm15445 ай бұрын
the bobbin should turn further to throw off the loop from the top thread around the bobbin. when it does the anti clocks movement it should go further. it must loop around the shuttle. between the shuttle and shuttle carrier.
@gmc20675 ай бұрын
parts are missing for takeup lever adjustment. length of stitch adjustment is too high. make sure your bobbin is threaded correctly into shuttle.
@piecetoyou82856 ай бұрын
I know its an old thread but, first thing is if you are not using the wax pot , then use bonded thread, also use same size thread for top and bottom, check the twist on the thread left or right, I can`t remember now but in the bobbin you can use left or right twist thread, but for the top you can only use a certain twist, I can`t remember now, I think your bobbin was up side down as well, check the thread is not to thick, for the groove of the needle,check your thread goes in the groove not to thin or thick for it, it should fit snug same as the eye of the needle ,not to loose or to tight, Hold your bobbing case pull about 7 inch of thread, wrap the beginning of the thread around your finger `now let the bobbing case dangle , give a quick jerk throwing your finger down about 2 inches and then back up in one motion, If the bobbing case drops all the way to the floor the tension is to lose , if it don`t drop at all the tension is to tight, if it drops about 3 inch and stops its good, check for bad rough area`s on the bobbin case and underneath the plate that covers the bobbin where the needle passes through, Place half a drop of oil underneath bobbin If its snapping thread the tension usually to tight ,or the thread its either to thick and jamming and getting caught, or thread is untwisting as it goes around if wrong twist or not waxed,or something is snagging is due to roughness, If you buy non genuine bobbins a lot from china do not fit correctly in the bobbin case you have to buy the China bobbin case as well , I think thread runs in between the gap , I am sure the timing may be out, I am sure one of the teeth on the cog has to be one tooth forwards than the other one, unless I am thinking of another patcher model, check for worn parts , like the driver pinion , you will have to remove it to have a good look , underneath it , And check all pathways the thread runs along is smooth and clean, and the thread is running of the spool smoothly , not to easy and not to stiff,
@malmal51588 ай бұрын
bobbin is upside down slin bobbin should be with slot faceing down ans pos rong bobbin it should not fit in that way
@raphaelseleman1310 Жыл бұрын
Hello may l have your contacts so that we may contact further because my singer 29k is not work may be you can help my singer work again.
@raphaelseleman1310 Жыл бұрын
Hello, l am from Tanzania and got the same problem how may you help to get the shadow and shadow carrier please?
@CarlosRodriguez-qb3yj Жыл бұрын
Mi máquina no avanza el prensatela
@5765203 Жыл бұрын
I had the same problem with my machine and it was the timing. The shuttle carrier has to be placed in the exact correct position and then the shuttle also has to be in the correct position. The wheel has to be turned to get the shuttle carrier in the right position. I was told the wheel had to be in the twelve o'clock position and then insert the shuttle in the correct position in the carrier then I was told by another that the wheel had to be in the nine o'clock position and put the carrier in facing just before the claw to pick up thread and that did the trick. It then picked up the thread from the needle at the exact position and both exited from the bobbin together and that worked fine.
@gergemall Жыл бұрын
I love it .
@fishhog3020 Жыл бұрын
Hello you get it sewing?
@victorbetancourt722 Жыл бұрын
God bless you I think Your machine is not on time do you want it done in time
@terrymcclean4582 Жыл бұрын
Watched your two videos today. In Part 1 at the 10:11 and 10:52 time stamps you can see that the bobbin turns clockwise when you pull on the thread. In Part 2 at the 1:20 time stamp you can see that the bobbin turns counterclockwise. I believe the bobbin should be turning counterclockwise as the bobbin thread is pulled off.
@grieche56 Жыл бұрын
sorry but you are destroying this machine with your ignorance
@VitalityMassage Жыл бұрын
That machine is beautiful Carolyn! So clean. No rust and perfect paint! Lucky you.
@boelensds2 жыл бұрын
see: yt: singer 29-4 timing and gear alignment schutztruppe 1900
@boelensds2 жыл бұрын
The botom gear and end is in the wrong position needs to be at the peace without the teeth. top one needs to be at the first teeth just touching.
@angelbogado21192 жыл бұрын
No hay en castellano
@bouchardsylvain95182 жыл бұрын
hello.. tell me the arm with 10 teeth not the smallest but the longest.. I would like to know how long it measures... me it is almost 32 cm.. on the internet those for sale only measure 19 cm ..thank you
@humbertopena6492 жыл бұрын
Un cordial saludo Me gusta mucho el video Es muy instructivo Mi nombre es Humberto pena Y le saludo desde el Salvador Tengo una máquina dé ésas Y me gustaría saber si puedo conseguir Repuestos para ésa máquina
@fakherjutt87032 жыл бұрын
Great
@fakherjutt87032 жыл бұрын
My machine problem same send me next part sticking upload plzzzz
@justsayyesradio74872 жыл бұрын
Looks like the wrong bobbin case.
@josephholster96263 жыл бұрын
Donde consigo el Manuel de la Singer 29-4. Saludos cordiales desde Chile 🇨🇱
@gulamhoosendocrat70913 жыл бұрын
How can you instruct us if you dont have the slightest clue about what you're doing ? It's a useless video in every sense of the word.
@domingolopez27153 жыл бұрын
Hola buenas tardes gracias por su video a ver si me podrá ayudar la mía es una 29k1 y esta fuera de punto le sabre agradecer la ayuda
@Artysmotosupply3 жыл бұрын
I'm having the same problem, did you find your answer?
@stasyskundelis28373 жыл бұрын
Lux.😂
@scottcleveland31273 жыл бұрын
Mine had the same issue and found out there was a broken part of a needle in the needle chuck that extended the needle too far into the shuttle. Using the correct needle I had great results right away.
@JimmyCogg3 жыл бұрын
I have the same problem and I'm struggling. I thing that the top thread, when it is caught by the bobbin carrier should slide under the bobbin carrier and loop around the bobbin and bobbin carrier. What is happening on your machine and mine is that the thread is being caught by the bobbin carrier but then trying to loop under the geared piece that carries the hooked bobbin carrier. Anyone who knows how to cure this I would be very grateful.
@michaellund6633 жыл бұрын
have bobbin thread facing you before you start.
@rogelioortizv35623 жыл бұрын
Un favor como se ajusta la barra de la auja la mía no esta centrada y no se como corregir ese problema un consejo gracias
@marcvermeylen48913 жыл бұрын
I think the upper tread is rotten en the tension too low to tilt the lower tread around and up .
@titillovaldes65043 жыл бұрын
Un favor como se ajusta la barra por qué no está centrada un consejo
@sergiogabrieljuarezavila78263 жыл бұрын
Hola soy de Argentina muy buen video...
@ismaelsalcedohernandez41753 жыл бұрын
Please in spanish.
@robertobustos82873 жыл бұрын
Quisiera poder escucharlo en español no puedo hacerlo
@danzar17293 жыл бұрын
Hi. Thanks for the video. How do you adjust the Stitch length on this machine.
@jayescreations4892 жыл бұрын
the stitch length is located on back of foot, the square piece and thumb skrew, with foot up you slide the square down as far as it will go for longest stitch. and tighten thumb skrew. if you have more question. look up the part in parts manual it will show the three pieces that go to length adjustment.
@porfiriosanches42524 жыл бұрын
Quiero escucharlo en español mi máquina no quiere subir el hilo de la bobina
@barblynch72254 жыл бұрын
The bobbin needs to be threaded with line to outside and insert into bobbin with line in bobbin down . . try that see how it works.
@chatzidimitriou1004 жыл бұрын
You are really an amazing woman!!!
@alejandrofloresibanez89744 жыл бұрын
Hola soy del estado de Veracruz, me interesa una maquina giratoria Singer.
@DonTomi834 жыл бұрын
I solved the problem, very similar to yours. turn the needle a little bit, clockwise. or towards the front that the eye of the needle is not straight, so that the thread can make the loop a little wider and the bobbin grasps the needle thread. Contact me if you still haven't solved that problem.
@AdrianMartinez-hy5dn4 жыл бұрын
Donde.conprar.repuestos.k cotizar presiosa de Malvinas tengo una sinjer.29 30
@saulogregoriogomezchavez72524 жыл бұрын
Cuanto lo vendes
@AdrianMartinez-hy5dn4 жыл бұрын
Megustaria es cuchara explicaciones en.español
@otealuajones82894 жыл бұрын
Hi Carolyn, I just got a 29-4 last month and I'm learning the machine. But I ran out of bobbin thread, can you tell me how do you wind the bobbin? And where did you find the manual for the machine from? Can you tell me which wheels are your belts on, top and bottom wheels? My belt broke and I don't remember which wheels it go on. Thanks.
@user-dy1wd2fk1h4 жыл бұрын
من چرخ سینجر دارم احتیاج به لوازم مانند کمپلت وماکو وماسوره دارد لطفا به این شماره خبر دهید ۰۹۹۰۳۵۰۱۸۰۵منتظرم و متشکرم
@user-dy1wd2fk1h4 жыл бұрын
سلام تهیه لوازم چرخ سینجر را اعلام کنید
@user-dy1wd2fk1h4 жыл бұрын
سلام لطفا دوبله کنید به زبان فارسی ممنون
@johne71304 жыл бұрын
her problem is that gear, the three tooth gear is the proper gear. The five tooth won't work, plus the idler gear is worn out. #1 is the drive gear (3 tooth) some guy back east had the 5 tooth made in china years ago. I bought one they were $88 each. my machine would not even turn over using the 5 t gear, then I work it and got the machine turning. Only then I could why the gear bind up. You hear saying she can feel the gears >> there binding and causing major play at the bobbin, the bobbin is in correct for a 29-4 these are not 29k's. if put in as Robert mentions it again will not turn over it has to be as shown. it is the WRONG gear. I called the seller and got the "your the only one complaining " Thats Bullshit I did get mine to work, only by hand, slowly. peddling is to fast it will do the same as she shows. all this took place 5 yrs ago