My situation with my razor do 1000 is reverse light just blinks and won’t engage into reverse but low and high just fine… codes reading on my 6591 and 6592, any suggestions only a year old model

Can you put spherical bushings in the shocks that come off of a Kawasaki treyx kfr 800? I am doing a cross cart build and the trailing arms are moving from the shock mount position and I am trying to keep from undoing the wields

For me i got lucky it was just a belt problem last week. All good to go now

Couldntt hear him

I have polaris 1000 turbo wont start and check ingine light is on What i do?

what diagnostic tool and software do you use?

2014 900XP, my rear shocks keep blowing oil. Replaced them and on the first ride, one of the new shocks leaked oil. My rear preload is only about 2 inches because I have High Lift A arms and Radius arms, 30" tires. my ground clearance is 13 1/2 in the rear and 14 1/4 in front. I really don't need more clearance but is my rear preload too short causing the shock to bottom out??? Any help would be appreciated.

Brother this is the first video I have seen step-by-step. Good job. I have looked at quite a few. Thank you very much!

Great video. Sounds pissed. Lol. Resetting mine today

We were out for ride just cruzin 40 mph and started to lose power no light came on tell we got home 10 miles away. We be good for bit then lose power and always when I got up to 40mph. Throwing code 90 and 92

You rebuild these for folks

this is exactly my problem grinding in any gear and belt is touching the edge in same spot . I’m going to remove a shim

Just as a heads up out there, he said 17 ft./lbs, or 204 ft/lbs on his torque wrench, when he meant 204 inch/lbs. I'm sure most of you caught it, but, just in case

Good morning my 2017 rzr runs grate for about a hour after that it goes in to limp mode no power and won’t idle just dies and it looks like it’s fouling out the spark plugs any ideas what it might be ?

Good morning I have a 2017 rzr xp4 that runs grate for about an hour after that it will go in to limp mode and have no power. After it cooled down it will run perfect agin any ideas of what the issue could be ?

So what was wrong with your rig?

How do u erase the check engine light ?

Excellent

My 900 is actually misfiring at throwing codes. Has fresh top end. And new head and Valves. Ran good for maybe 30 miles. Now runs terrible and spitting sputtering and popping. Has new fuel pump too. I’m lost!!! Maybe jumped a tooth I just don’t know. Thanks

Hello Gary, We just purchased a Polaris 2018 General 4 1000 with 518 miles on it. We have taken it out for several rides and it started just fine. Tried to go for a ride yesterday and it wouldn't start. Cleaned the battery terminals. No start. Purchased a new battery and installed it. No start. The dash lights turn on, the headlights turn on. Any suggestions you could provide would be appreciated. Thank you! Robyn

Do you have a part number for a rebuild kit? With all the different fox shocks I want to make sure I gwt tge correct kit. 16 900s with fox 2.0.

That cover is a pain in the ass to get out

Thank you for this video. I've had my 2017 xp4 turbo for last 2 years and just recently on my last 2 trips I've gotten codes 35590 and 35991 my machine pops these codes after about hr of running the machine hard and I loose all power. I turn off machine wait a min and turn it back on and I have power again then drive about a mile and codes go away then about another hr or 2 I'll be fine before I repeat process. This is never happened to me until this year and was after I did my maintenance on it. Changed all fluids in machine new brakes new plugs cleaned out belt and clutch new s n b air filter. I do have an s n b air filter separator kit on machine and a blow hole for belt with a scoop going into the frogskin. I don't have the equipment u have but where do u think I should start?

What brand is that rear cargo cage? I like that. Is it still made in 2023?

this is what i am looking for ,my 22 just got a check engine light when i was out yesterday ,once i find the problem how do you clear the light ? and below you say Most common problem is valve’s out of adjustment ,how do you know if its the valves ,is it noise or just from experience

Hey Gary I have a 2021 rzr 1000 . The engine has a miss # 1 cly when the engine gets a little heat it runs fine. I have good spark on that cly and the injector has 12 volts. Not sure about the ground signal from the ecm . One other thing is about 50 mph the engine will lose power you can turn the engine off with it still in high gear turn the switch back on and it's fine until till you reach 50 mph again. Thank you

So what was wrong with that machine? you never said what was wrong

Cant you adjust em at full droop?

Thanks for posting! This is valuable info! :)

cut the music down

Hello, I have a 2017 Polaris general. It sputters in park if I hit the gas. I was wondering where you got tour check test program from.

Good video tutorial

I love mine!!!!!!

I have a 2016 RZR 1000S Hard staring when cold. They took to a dealer, and they went through and the only thing they found was cyl low compression. They updated the computer and when through with scanner If, I prime it in the morning it starts all day.

Where did you get those wheels?

Super informative video. Thank you

Nice Video Bro!

Nice video! Just purchased a 2017 highlifter 1000 ranger XP and didn't notice until we got it home that it has this "rattle" or "rocks spinning in a can" noise up front. Doesn't do it in 4x4 though. Only has 760 miles and now I'm worried it needs a front diff. Different forums say to upgrade the prop shaft to the cv style and that fixes the noise everyone has. Is this accurate? Would love your opinion if you see this after 2 yrs of this video!!

Hi great video. Did you have to re clock/rotate the springs after you got them installed? Thanks

If you removed the cargo box from the start, you don’t have the true ride height. Shameful.

Should probably read the manual on this one... way off. And where's the Loctite?

Why would you not replace the top springs or getting a drs. It can’t feel good driving it compared to how it should be feeling.

11:11 Whats that sound. Mine sounds like that every time I turn off my rzr?

What bed rack is that

I am looking at replicating this exact build on my 2018 general. Was there any clearance issues or tire rubbing with this setup?

Did you only adjust the tender springs, or did you do the lower springs too?

Good job guys.

very informative. not for adjusting but you may have saved me from buying new shocks

What size spacers did you go with?

Is it looking for rear shocks for a Honda Odyssey Fl350