I wonder if your wildcat is still running on the same engine
@AndrewB416 Жыл бұрын
Just found this video. I've got a 2018 Frontier Pro-4X with the OEM rack and the local dealer wants $488 for the front cross bar. Absolutely insane. I'll be heading down to the local hardware stores looking for superstrut tomorrow morning. It looks like the 2" clamps are hard to find but I'll find something that'll work. Thanks for the video.
@triprovoked5082 жыл бұрын
Thanks for posting.
@backwoodschan2 жыл бұрын
4 years old but top of the etch marks is full, NOT where is says "FULL"
@OverkillKillerr3 жыл бұрын
Thank You!
@DaveBuildsIt3 жыл бұрын
This is a great video. I have been struggling to find crossbars for my Xterra without paying a mint for the OEMs. You definitely saved me a lot of research. Thanks!
@oldhoosier23 жыл бұрын
your opening ended the playback!
@bill_maryjohandrahan7173 жыл бұрын
Great video Eddie. I’ve been told the round tubes are fairly stout but that flat piece is garbage. You had mentioned in a reply that you use the flat plates underneath the roof and above the roof liner. Is there one large plate on each corner? You didn’t by chance get any photographs of that did you? I’ve never seen underneath the headliner. I was hoping for some type of a support pillar running from the A to the C pillar. But I’m guessing it’s just a flat piece of metal with a support plate underneath it. Thank you for your reply.
@rogerallenhambel93413 жыл бұрын
Love how he skipped over how to break the fill screw loose. / or tighten it back up. Great editing 🤦♂️
@jameshayes1163 жыл бұрын
You could always make your own videos.
@rogerallenhambel93413 жыл бұрын
or you could make better videos
@houndhunter41066 ай бұрын
If you need help figuring out how to loosen bolts, you should just stay away from tools.@@rogerallenhambel9341
@AerialKentucky3 ай бұрын
Turn it left for off, right for on. Craaaazy he left the out smh😂
@Jsantosishere3 жыл бұрын
I put 22 2x6’s on the oem rack!... it was bad idea
@davidholt42163 жыл бұрын
Nice work and thanks for sharing. I've had my truck for 10 years, but never needed the rack until this year. I've used the current setup a few times, and haven't had any issues, but those support bars do seem pretty wimpy. Think I'll do this mod.
@FostaFunk4 жыл бұрын
Awesome idea and video! About to do this to my truck tonight. What kayak J hook holders did you end up using?
@Chris-kw6fs4 жыл бұрын
Just a couple of quick comments on a good video series. The engine oil change is about 2.6 quarts as stated below and as per manual. The top of the crosscheck on the dipstick is full. As stated below by James Sparks. Also, make sure you start your rig and let some oil get into the filter before you do your final check and thread the dipstick in to do this check. Do not overfill as John B stated.
@Chris-kw6fs4 жыл бұрын
My 2020 Trail has no level inspection plug in the front diff. So I just added oil to the filler plug until it over bled. took a little over 6 fl. oz. like the manual stated. As for the question from Jordan below, I used the same Castrol Limited Slip 80w90 oil he used as he showed in Vid 1 one of this series.
@jordanperon75234 жыл бұрын
What kind of oil u use
@LukeTN274 жыл бұрын
Thank you for this vid. Was trying to figure out how to get my kayak on my xterra without ordering new holders. I am going to do this right now.
@jamessparks74804 жыл бұрын
the top of the etching area is full not halfway up the dip stick
@ken37005 жыл бұрын
How come people never power wash their toys?
@eddietheheadful5 жыл бұрын
I power wash mine all the time. I take off all the parts that will come off and spray all of the mud out of it.
@mdkrush5 жыл бұрын
Thanks!!!
@Sniper_Cat_715 жыл бұрын
Man, this is perfect. I have an Arksen cargo basket that fit perfectly on my old Mariner, but I just bought a Pro 4X Frontier and the basket is too wide for the brackets to grab onto the Nissan cross bars because they sit too low. Great solution, thanks!
@traceykays4336 жыл бұрын
Does the wind blow through the holes and make noise?
@eddietheheadful6 жыл бұрын
Tracey Kays no I have not had any problem with that.
@Winchestersxp6 жыл бұрын
Find some rubber caps for the ends and it would look factory...good Job !!!
@mikegardner19206 жыл бұрын
Thank you! Thank you! Thank you! Great videos
@damiandeprada716 жыл бұрын
I've had my 14 mod 22 hrs old, please a vid to fix it all up bumper to bumper.
@ginoasci28766 жыл бұрын
I have the same truck 2014 which did not come with the roof racks. Does your roof support those ra ks ok? I was told by the dealer that you can't install them after the fact because thge roof doesn't have rthe supports that are installed by the factory. Where did you get yours, and how were they to install?
@justintdavis20105 жыл бұрын
@Eddietheheadful, could you answer this
@eddietheheadful5 жыл бұрын
I got the rack off of ebay. It wasn't to bad to install if you are comfortable drilling 16 holes into your roof.
@gene52519695 жыл бұрын
@@eddietheheadful besides drilling 16 holes in roof, what else is involved? Does inside trim and headliner have to come out? I just purchased a brand new 2019 frontier Monday and also was told it couldn't be done.
@eddietheheadful5 жыл бұрын
@@gene5251969 I dropped my headliner. I used the threaded plates that came with the rack. They are a little more structurally sound than the rivnuts in my opinion. You can drill holes and use the rivnuts without dropping the headliner, but all the more it takes to do it, I'd suggest that and using the plates. I hope that helps ya.
@tylerbell72306 жыл бұрын
Hey Eddie... I’m doing my first service (200 miles) on my 17’ wildcat trail. Will all these fluids be the same as what I need on my Model? And is there anything I need to add To it for first service? Thanks.
@willyhughes86006 жыл бұрын
nice. what size kayak is that?
@eddietheheadful6 жыл бұрын
Willy Don it is 10.5 feet long
@devinkarnes42426 жыл бұрын
Can you do a video on how you installed those greese fittings ?
@nuckfan57 жыл бұрын
good job on the vid..thanks! Also i noticed the grease zerks on you a-arms. I was thinking of doing this as well. Did you change the stock bushings?
@eddietheheadful7 жыл бұрын
nuckfan Stock bushings still as tight as new at 1000 miles. Grease fittings were the first thing I did before I ever rode it. I highly recommend them. That is why the stock bushings get such a bad rap. If you grease the water out, they will last a long time.
@roycemccarthy57717 жыл бұрын
I recently bought the same machine, mine doesn't have grease fittings. nuckfans question answered mine. for the price I paid I would have thought they would have been installed.