GarageVlogBob

Пікірлер

@Optanax 4 күн бұрын

I agree but you might want a skid plate

@GarageVlogBob 4 күн бұрын

The bike has a skid plate on it and in all the pics and videos

@reese647 6 күн бұрын

Great bike

@GarageVlogBob 6 күн бұрын

Thanks just finished it up

@Gavin-hr2tn 10 күн бұрын

Every fuckijg time 😂😂

@adrianofloiran8058 15 күн бұрын

2022 3500 same problem 😢

@GarageVlogBob 15 күн бұрын

That sucks. You would think they would figure out a solution by now

@adrianofloiran8058 15 күн бұрын

@ i go to the dealer like 3 time shit the same problem and still

@maxcox6019 Ай бұрын

I have the same issue with my 2018 the light comes on and off and dings all the time

@GarageVlogBob Ай бұрын

Are you sure it's the same code? Sounds more like a 0020 issue with abs pump

@maxcox6019 Ай бұрын

@GarageVlogBob I'm not sure the code off hand but hitting bumps seam to make it do it so I believe it's a loose wire

@GarageVlogBob Ай бұрын

Don't assume anything get the code and know what your trying to fix before you start tossing ideas and money at your truck

@JuanRodriguez-vb4yb Ай бұрын

TY 👍

@randycrawford2318 Ай бұрын

Great video. Glad I found it. Quick question. I have two sets of new ball joints, different manufacturer’s and neither of them fit in a 1 1/8 12 pt socket. Do you think that I could have the wrong size ball joints? I ordered both pairs from amazon. First pair I tried to install using the freeze/heat method and they wouldnt go in so I ordered a second set, different company. Havent tried them yet but the fact that they dont fit in the socket like yours does has me concerened a little bit

@GarageVlogBob Ай бұрын

The size of the drive socket isn't all that important. You just need something to drive that ball joint back into place. I used that socket because it fit for what I was doing. If you find a socket that is the same out side diameter as the ball joint you will be all set

@randycrawford2318 Ай бұрын

@@GarageVlogBob thanks for the reply. Went and returned the 1 1/8 socket and bought a 1 3/16 socket today. The ball joint I have seemed to fit that size perfect. Going to try and tap it in tomorrow. Hopefully that does the trick. Thanks again for posting your video

@charlessmith3701 2 ай бұрын

Would your truck go into 4wheel drive while the light was on ?

@GarageVlogBob 2 ай бұрын

With that issue I found if I needed to use 4x4 I would make the switch before I would turn the key on. Once turning the key on it would switch to the selected 4x4 position and stay I would have to do the same thing to put it back in 4x2

@GuillermoAlvaradoHernandez 2 ай бұрын

A cuentas vueltas va la esprea de el aire?

@GarageVlogBob 2 ай бұрын

I'm unsure what you are asking

@haleyallen6523 3 ай бұрын

Mines bogging out quarter to full throttle I’ve tried resetting belt I’ve got belt box apart put switch to on position cleaned everything and it’s still bogging down quarter to full throttle

@GarageVlogBob 3 ай бұрын

Sounds like your main jet it plugged

@rileyjones9693 4 күн бұрын

yea mines kinda doing the same. it won’t rev up past 2nd gear. it gets to a certain RPM and just revs at that level.

@stealthynoodle2707 3 ай бұрын

How goes it? Everything holding up alright? Tempted to do a swap myself, but this is only the second instance ive seen of a CG250 swap, the first being the Vader reddit post

@GarageVlogBob 3 ай бұрын

Worked great, best mod I have ever done. The extra gears make a huge difference, and it was cheap

@Dingdongop 3 ай бұрын

Batman has gone downhill

@UptownFights 3 ай бұрын

Whats up Bob! How you doing? I have an issue with mine keeps leaking out the propeller shaft seal. There's much play side to side and forward backward in my shaft. How far down does your propeller shaft house sit inside the lower unit? Min is like 7/16s and it's super tight. I don't want to strip mine out. I suspect mine housing is not sitting on the inner bearing. I have a video I can sent. Nobody has theys Daddy Kings on youtube except us. kzbin.infoiFtB7FJMQKs?si=0B4VbENNNB5qRVH8

@GarageVlogBob 3 ай бұрын

Unfortunately I'm of no help on that one

@jeremynelsen4382 3 ай бұрын

What are the electric plugs for? I have the exact same 4 wheeler and all the carb replacements I find don’t have one of the electric plugs.

@clayyng 3 ай бұрын

Ever find the fix? Had severe transmission issues with not shifting/slipping would come and go, eventually just started acting perfectly fine now it’s going this, obviously electrical issue.

@joshlindemeier2434 4 ай бұрын

Using an impact will usually help to break the trim cylinder nuts loose without spinning the shaft 👌

@GarageVlogBob 3 ай бұрын

Although I do have one, most don't, that's why I didn't use one in the video

@creasybear4426 4 ай бұрын

🥱🥱🥱

@mikeb6300 4 ай бұрын

I have the same year and color 2500 megacab limited I have no issues but thank you for the heads up, but May I suggest that you put some dielectric grease on connector prior to reconnecting

@GarageVlogBob 4 ай бұрын

It already had some from a previous repair attempt

@ryancaldwell5197 5 ай бұрын

Hey I did everything step for step and now my four wheeler cranks up right away but as soon as I start it it’s revving high like I have the throttle pushed in? Any advice?

@GarageVlogBob 5 ай бұрын

You don't have the throttle cable installed correctly it's to tight

@patrickjohnson7801 5 ай бұрын

I Shure wish Blackstone would have a stainless steel up grade

@GarageVlogBob 5 ай бұрын

There are options with other companies

@patrickjohnson7801 5 ай бұрын

@@GarageVlogBob I have a little griddle that is a insert for my 4 burner bbq and almost indestructible, but I like what you did for sure

@Yaboyjo-s2f 5 ай бұрын

I jumped

@GarageVlogBob 5 ай бұрын

Sweet

@matthewhenderson2236 5 ай бұрын

I’ve noticed this as well. Every professional kitchen I’ve ever been had a near glass smooth griddle surfaces. All of these residential griddles have some sort of texture on them. Maybe it’s a price point issue. Perhaps folks are just cooking at way too high of temperatures causing the burning and thus bonding of the food material to the metal surface of the griddle. Chefs and experts alike say that outside of very specific cooking circumstances high heat is never to be used. Medium to medium-high is more than sufficient. High heat promotes food material bonding to the metal surface making extremely difficult to clean.

@GarageVlogBob 5 ай бұрын

Unsure

@matthewhenderson2236 5 ай бұрын

@GarageVlogBob 5 ай бұрын

Unsure

@D3moknight 4 ай бұрын

It's the difference in how the flat top is made. Commercial flat tops are made more by forging thick slabs of steel vs the Blackstone griddles having like a cast iron texture.

@superjetfreak 5 ай бұрын

You can change the starter without removing the clutch or cover!

@GarageVlogBob 5 ай бұрын

Can you? Yes. Is it more work than just pulling the cover. Yes

@cowboybeebop3451 6 ай бұрын

Top speed?

@GarageVlogBob 5 ай бұрын

Low 70s

@imod2835 6 ай бұрын

I lost spark after this

@GarageVlogBob 5 ай бұрын

Spark has nothing to do with a reset

@Big0veralls 7 ай бұрын

What lift model is that and where’d you get it? I need that thing bad.

@GarageVlogBob 7 ай бұрын

That's a dirtbike lift stand off ebay or Amazon. They are nice but heavy. Now I use a lift table from harbor freight that is a lot easier to work with. Rolls under machines lifts same height

@Big0veralls 7 ай бұрын

@@GarageVlogBob I’m surprised the one for the dirt bike lifted it. Which weight capacity harbor freight lift did you get? I have a Timberwolf that I’m working on but it says it’s 529 pounds in the manual and the lifts I looked at don’t hold that much if I remember correctly.

@GarageVlogBob 7 ай бұрын

Currently I have the 500lbs one and it works fine for that machine but struggles on bigger 4x4 machines and I also use it to lift one end of my sxs and it struggles. I wish I purchased the 1000lbs one because I do a lot of heavy atv repairs. I'm not willing to buy the bigger one until my 500lbs finally gives out. 4 years strong. If your not doing big machines you can easily stick with the 500lbs one because it's a Lil lower to the ground witch helps

@Big0veralls 7 ай бұрын

@@GarageVlogBob awesome man. Thank you. That Timberwolf is the only thing I’d use it for.

@GarageVlogBob 7 ай бұрын

I would stick with the 500lbs one then. It fits under sport quads. I'm not sure if the 1000lbs one would be low enough

@howardhartman127 7 ай бұрын

Only if it worked. Tried it no change

@GarageVlogBob 7 ай бұрын

Sorry I had success with it

@chevyseductive 8 ай бұрын

Alright well thank you 1 person of the universe for making this video for my exact autistic special interests solution! I have all the tools to solve this meltdown and getting to work!😂

@GarageVlogBob 8 ай бұрын

Your welcome 🤷‍♂️

@chevyseductive 8 ай бұрын

@@GarageVlogBob have a great spring!

@GarageVlogBob 8 ай бұрын

Thanks same to you