Rosenbellion

Пікірлер

@mattwehbe7824 4 ай бұрын

I had the same issue with the gasket. The issue is that its the CVT vs auto 4 speed. I was able to get the gasket from Nissan. the Gasket you have is for CVT only

@robertstercraw9284 14 күн бұрын

No, that's not it. The CVT gasket is shaped nothing like the 4 speed auto. The gasket is correct for the older 4 speed automatic found in the 1991-2006 Sentra. When Nissan put this transmission in the Versa for 2007 they changed the position of ONE bolt he points out at 9:21. None of the aftermarket suppliers picked up on this change.

@chefkarimassaf268 7 ай бұрын

I have the same problem and I'm working on it right now but I just want to ask you if the transmission fluid is regular or CVT fluid? Does the fluid look red or clear like vegetable oil? I didn't take the gasket off of the oil pan, should I put it back?

@masonloh1411 7 ай бұрын

Rosenbellion - Just to make sure, this is a 5 Speed Traditional auto, correct? None Cvt. Thanks

@masonloh1411 7 ай бұрын

Same problem here w/ Wrong Wit Filter. ordered Nissan Genuine Filter same wrong & Gasket!!!

@nahmean7036 8 ай бұрын

Thanks for talking about the bearing seating

@felixgonzalez7765 Жыл бұрын

Did u go to 👉W I t 👈 transmission parts They have it .

@deadmoney2093 Жыл бұрын

What year is this versa? 1.8 liter engine?

@patsantiago6206 Жыл бұрын

I had to have an owl eye to watch this video!!!!!!!!!

@buggzo Жыл бұрын

What car is this install on?

@rosenbellion1537 Жыл бұрын

2011 mustang

@vagabond2849 Жыл бұрын

Quick question I removed filter bolt only one different I can’t tighten could you please to teach me how Thank you

@rosenbellion1537 Жыл бұрын

You’ll need to make sure your threads are matching up. Try loosening the other bolts a little and try to put that one first.

@HB-yq8gy Жыл бұрын

Yes that's the same problem I am having with my son's 2012 Cube 1.8L S. I ordered from the Nissan dealer with the vin # to make sure I had all the correct parts. I knew it would be diffucult. Also now I can compare what after-market parts will fit. I did order the ATP B-130 CVT trans gasket kit from Amazon for the 2011 Cube gasket didn't fit😅

@ryanculler7324 2 жыл бұрын

I have a 2002 sequoia my drive belt is rubbing the front cover of the tensioner assembly I went to auto zone and they only have either just the pully or can get whole assembly for 30 more dollars but they are different sizes but still compatible I just dint want to take whole thing off if I can just change pully itself so gonna go check if my tensioner is on correct position thanks

@LuisRojas-uu4om Жыл бұрын

Oreilly has the 102mm tensioner pulley wheel

@dtchevy7317 Жыл бұрын

Does it spin or is it on a fixed position when running? Thanks

@robkelley95 2 жыл бұрын

No mention on how much fuild it takes after the filter change Just dumb info, put back what came out, we'll what if it's low before your going refill it low, how about the proper info on refill Hard to find info

@lifewith26gang45 2 жыл бұрын

Hey you hook up a 2011gt wire hornist on on a 2013 mustang v6????

@Deville_1979 2 жыл бұрын

Have you bagged the mustang yet been searching for suspension parts and info I’m trying to tuck 20s on a 2008 mustang static no bags 🧐

@rickmiller1138 2 жыл бұрын

lefty tighty right loosie on tensioner pulley

@furniturerescue3949 2 жыл бұрын

The sticker comment had me laughing. Thanks for posting this it helped.

@glenjamindle 2 жыл бұрын

I remember my first time using power tools. Pro tip: Screw the smaller hole saw INSIDE the larger hole saw so it acts as a guide. Also, drill in reverse to get the hole started especially on an uneven surface.

@mattgameplay6477 2 жыл бұрын

So red (positive) to the fuse box ?

@mpcustoms7803 2 жыл бұрын

I'm having the same issue did you fix it

@Nathan-jv8pj Жыл бұрын

Did you find out how to fix

@mpcustoms7803 Жыл бұрын

@Nathan I have not sometimes it changes the same colors as the ambient light when I change it but it'll go back to a different color.

@Nathan-jv8pj Жыл бұрын

I'm afraid I might have to go buy a new one just to fix it...

@czthjvv 2 жыл бұрын

Did you notice any MPG increase or increase in low end torque? Faster acceleration off the line?

@RavenCyclone 2 жыл бұрын

Mine on my 12 doesn't light up on driver's side, any idea of a fix?

@Subie-zy4jq 11 ай бұрын

Hey I’m having the same issue did you fix yours?

@tcgcolio3822 3 жыл бұрын

You put it on the wrong side dumbass thanks for prolonging this process ,, people if your gonna make a tutorial know what your doing!!

@michaeledwards3100 3 жыл бұрын

Easier to work from bottom

@mattmahoney8659 3 жыл бұрын

This video kzbin.info/www/bejne/b4O1lGVqdsp0rc0 helped me use it without the 2" saw fusing to the other stuff. In short, put washer on back of saw, put nut through washer into back of the saw. Tighten with hex wrentch ( I used a 19mm which was the closest fit that I had ). Screw arbor into back of nut hole ( don't remember if I tightened with hex wrench again ). Attach to drill. Do the thing. Detach drill. Use hex wrench to loosen and unscrew arbor, nut, and washer from saw. Hope this helps anyone out there who finds themselves in the same situation.

@victorv7713 3 жыл бұрын

Thank you for making this video saved me some nice cash. I also had no luck with anyone having the correct gasket even online. Ended up reusing the old gasket with no issues. Thanks again

@leonardlafrance2869 3 жыл бұрын

common sence, do the video day light,how in the world i suppose to see what the hell your doing dummy!

@leshowie9772 3 жыл бұрын

Don't forget to tell them that this has left handed threads.

@robertdanorth4509 4 жыл бұрын

No it's not 20.5 gallons per mile it's 20.5 miles per gallon.

@robertdanorth4509 4 жыл бұрын

No you put the gasket between the manifold and the throttle body spacer!

@rubencitostyle 4 жыл бұрын

ended up jere because I was having the same issue - going to re do it again and hope that it doesn’t get stuck - I may get the quick release attachment! thanks for the vid!

@uknowh0 4 жыл бұрын

Same problem over here! Ended up getting the bit stuck!

@motogun1040 4 жыл бұрын

you are awesome ty bro

@tedfritsch3340 4 жыл бұрын

Milwaukee also makes a "Quick" release arbor bit works like a champ. The quick release has a clutch and makes the hole saw tight with no wobble. Super fast on and off, no matter the size of the saw.

@peterc2171 4 жыл бұрын

Milwaukee should include instructions. For my set, there is none. I struggled same thing as you.

@brucesparks5487 4 жыл бұрын

If you read the reviews on this set they’re all negative, basically its meant to over torque the bit fusing it to the arbor. Once it’s fused it’s almost impossible to switch the arbor to other hole saws. Terrible engineering that you can tell was not designed by anyone with a decent understanding of how these are supposed to actually work.

@khalidabdo7101 4 жыл бұрын

Same problem with gasket my question is can I use the old gasket that in the pan?

@perrydemetro 4 жыл бұрын

You already have a V6 why do you wanna save more gas

@rosenbellion1537 4 жыл бұрын

I honestly just wanted to see if the hype was real. I installed a cold air intake so I had to take it out anyway

@ericdeleon93 4 жыл бұрын

did you have to grease both ends of the control arm or is the grease it comes with plenty? i changed my out and it creeks and cracks with every bump

@rosenbellion1537 4 жыл бұрын

ericdeleon93 at first I didn’t. I then took it back out and greased every fitting with a grease gun. I also greased the hole the bolt passes through that holds the arm to the body. That minimized the creeks. I have noticed the creeks go away in cold weather. So I might have to pull the arm and and regrease everything again. I jumped on the forums and almost all of the reviews have some complaint about creeks in them. You also need to grease them every couple of months.

@Motorrad127 4 ай бұрын

You guys ever ride on air? You can't feel the road surface, which totally defeats the purpose of performance arms..🧐

@iraqiforever7135 4 жыл бұрын

That was very helpful, thank you

@semperfi1214 4 жыл бұрын

Thanks for video

@MustangGuy2000 4 жыл бұрын

Do you have to torque down the throttle body spacer to a specific torque spec? I'm not sure what it is

@rosenbellion1537 4 жыл бұрын

No. The spacer it’s self doesn’t have any stand alone bolts. It gets sandwiched by the manifold and the throttle body.

@Jfizzle813 4 жыл бұрын

Did you wire them up yourself or was yours plug and play ??

@rosenbellion1537 4 жыл бұрын

Jeremy Beaver they come with the car so plug and play.

@Nathan-jv8pj Жыл бұрын

Did yall figure out the issue

@1976kinggoldenflair 4 жыл бұрын

I am having same problem either way. Picked the wrong set. Diablo set should be easier.

@gpherbert 4 жыл бұрын

Nice work, stressful install,

@JamesYoung99811 4 жыл бұрын

Hello, May I ask if you ever got all 4 of the fog lights to run at the same time. I am having the same problem where I cant have both sets of fog lights on at the same time. If you did, could you let me know what you spliced to get it working?

@rosenbellion1537 4 жыл бұрын

So there’s two sets of relays. If you remove the set of relays for the two lower fogs you can get all for to turn. I don’t know if it will burn out the other set of relays if you leave them on all the time. It’s recommended you have one relay per fog though. I did want to splice wires for the mere fact that (at least where I live) it’s illegal to have two set of fogs on at the same time. But if you don’t care about that all you would really have to is eliminate the toggle switch, that one that lets you select which fogs you want on. Then take those wires and time in the power for your regular fogs. One switch would control all four fogs. If need help I could make a short video for you when I have time.

@JamesYoung99811 4 жыл бұрын

@@rosenbellion1537 Thank you for the great response *Thumbs up

@JamesYoung99811 4 жыл бұрын

I will let you know if I need the video, thank you. I'm going to give it a try within the week.

@CH47Flyingtwinkie 4 жыл бұрын

Sorry to reply to an old video, where did you purchase your filter?

@rosenbellion1537 4 жыл бұрын

The Flying Twinkie advance auto parts

@needsaride15126 2 жыл бұрын

@@rosenbellion1537 Maybe next time see if a Nissan dealership has the gasket.

@brandon6333 4 жыл бұрын

i need those fog lights man my visibility with my raxiom s550 style headlights suck. so this was done on what looks like the 3.7 correct? how easy is it to install the bottom foglights?

@rosenbellion1537 4 жыл бұрын

Yep 3.7. It’s pretty straight forward as long as you’re bumper has the brackets for the lower fogs. If remember correctly there was four screws, two for each light. Took maybe an hour to do at the most.

@dobishs 4 жыл бұрын

This video proves they should include better instructions. Now try removing after tightening the bit.

@prionaloc9356 4 жыл бұрын

Thanks. I just recently put these on my car. Originally bought the ql-38 but ended up buying the ql-50 because they were slightly longer. Good job on the install.

@rosenbellion1537 4 жыл бұрын

Prion Aloc thank you for the comment! I’m glad you liked the video. So far I’ve really like my quick latch products. I haven’t had an trouble with them.

Ең жақсы KZbin

Пікірлер