Joe Michael Lemus

Пікірлер

@jbcustom3745 7 ай бұрын

did you swap out the spring also? my slide is hiccuping when trying to go into battery from slide release

@teamblue147 7 ай бұрын

Factory spring was transferred over and I’ve never had a problem with it since I changed out the guide rod. Best upgrade you can do to this gun

@Victor-tc3de 4 ай бұрын

Was the slide not going into full with the original guide rod? Changing the guide rod only without the spring also fixed it?@@teamblue147

@teamblue147 4 ай бұрын

@@Victor-tc3de I had a lot of failure to feed and battery problems for some reason but when I switched the rod over it literally fixed it and I never had that problem again. For me it’s by far the best solution that I could have ever asked for.

@d1ndark25 Жыл бұрын

After taking apart the FN 502, the factory guide rod is cheap as hell. Cheap thin plastic. This one will last forever so why not.

@theebigda Жыл бұрын

This shows the install... kzbin.info/www/bejne/mYnXe6ailK-FmqM

@elvergalarga8477 2 жыл бұрын

Joe i noticed when you insert the magazine, you gently push it in, and i was wondering if you push it lil harder, would it have problems feeding or failure to fire ?

@teamblue147 2 жыл бұрын

No problem what so ever I have 1000s of rounds through the gun and I shoot it with a suppressor also and that thing is awesome. If I have problems it’s usually with the amo and not the gun itself. Changing out the rod really made a huge difference.

@sachmo0196 Жыл бұрын

Good question! My FN502 (may2023) had all 3 mags (bought additional) fall apart when I did a regular slap-in! every time. After review of the mechanism(s), I came to the conclusion that the design was in error. Not an issue for me cause "I fix sh*t!". Additionally, the Mag release is too big and a simple touch allows it to release. Remedy: I ground down 1/8" on each side, coated, and now it operates as normal (purposeful release). Note: a stronger spring could be added (should be). Also...(sorry) but, slop in magwell is insane! Fixed it with homemade shims at base and slop is gone. As for another persons Q&A...The Guide Rod/Spring replacement is a must. Why?: Springs vary for a reason and plastic rods w/open ended springs catch on plastic for one. 2...I have 1200/1640 FPS rounds and the slam-back may ruin the operation of the gun (power). If the weap is used for plinking, just have original on hand and swap to newer one as needed (quick/easy). Never throw away parts, you may need them :)

@elliotmell3185 2 жыл бұрын

Bro xD during the report out I don't think the judge knew what to do cause he didn't report out in English 💀

@teamblue147 2 жыл бұрын

I see what you mean he sat there for a second or two lol 😂

@ellissmithjr6599 2 жыл бұрын

The SS guide rod is Always better than the plastic original... you may regret in Not replacing it. Also I replaced the original spring in mine with a Sig P250 spring,it is stronger that doesn't allow the slide to be slammed so much back and forth in which the you will have a better smother slide action 👍😎🇺🇸🇺🇸🇺🇸.

@teamblue147 2 жыл бұрын

I will have to take a look at the Sig spring but so far the original one is working good for me thank you 👍

@ellissmithjr6599 2 жыл бұрын

@@teamblue147 P250 chambered for 22LR

@joguns2005 2 жыл бұрын

@@ellissmithjr6599 are you able to shoot ammo subsonic, and standard vol, with the sig spring? thx

@ellissmithjr6599 2 жыл бұрын

@@joguns2005 😎👍🇺🇸🇺🇸🇺🇸 Standard velocity

@joguns2005 2 жыл бұрын

@@ellissmithjr6599 thx

@djchurchey 2 жыл бұрын

Can you elaborate as to how this improved performance?

@teamblue147 2 жыл бұрын

Is intended to add mass to the muzzle end of your FN 502 to aid in the reduction of muzzle rise and sight return after a shot is fired.

@tacleohjoe7577 2 жыл бұрын

You just use you’re original spring ?

@teamblue147 2 жыл бұрын

Yes

@chrismartinez8393 2 жыл бұрын

Can you post the website where you got this. I'm looking on Apex website but nothing there Thanks

@teamblue147 2 жыл бұрын

They well be available in the next week or so from apex just keep a eye out on their website

@MrZLE99 2 жыл бұрын

Overall pretty good and decent!!! I would recheck the regulation for the left face executed at port arms however..

@3raser6 3 жыл бұрын

army drill team is a little ass this year

@teamblue147 3 жыл бұрын

gamer this was just the two soloists that performed I don’t know why the whole team was not there but it was still cool to see them

@MrZLE99 4 жыл бұрын

Good to see SJG having a full block again but the routine is somewhat slow and could use more snap and pop.Wouldn’t hurt to pick up the speed a little and utilize the more of the drill pad by marching proficiency. But overall decent job, y’all definitely have the people to make it happen, most of the team is in unison with having the same level of rifle skill, continue making the routine more complex and intricate.

@exert9995 4 жыл бұрын

H u h

@timsmith8685 4 жыл бұрын

Hubba hubba hubba I am amazing

@samuelmatthews9092 4 жыл бұрын

Fair Routine. Unison has improved some, but Snap and Precision are non-existent here. In other news, How'd they get a Medical Officer (The 0-3 Captain) to Judge at the Nationals??

@MrZLE99 4 жыл бұрын

Herr Smitzinger He’s post HS competitor in the World Drill Championship and has actually placed, usually when’s there’s officers judging they have experience in this