Came to the comment section to comment on the disk, nvm 😂

yeah that aint right. theres no relief.

Способ заточки лопат!

Naj važniji detalj niko ne govori. Neznam zašto. Nije toliko važna kosina koju prodajj. Važniha je ona ( popreka) ona od prednjeg djela oštrice prema zadnjem. Značj potrebno je pravilno ZAKRENITI borer da bi dobio ištrinb ilm tuplju oštrico. Za tvrđi matrijal tuplnu za mekši ( drvo) oštriju.

Works until the disk shatter and cuts you up

I think you used a cutting disc for click bait 😂

Do you have a 3d printable file for this?

輔助工具

And how does the underside get reshaped? And the center...

That's not a good idea. Side wall a cutting blade is a no no. I am all for breaking the rules until I found out for myself.

Just a tip, change out that grinder wheel dude. I neglected changes those things out frequently and had one vaporize on me. Luckily nothing hit my face but I have a buddy with a pretty good scar on his face near his eye when one of those exploded on him. If you see jagged edges, replace that thing

Очень умно, совать пальцы под диск.👍

Drills must be rolled through a very specific geometry while sharpening. These flat faces are too aggressive and will cause the bit to shatter when used.

Nothing wrong what he's doing great idea why are people so negative give credit were it's due instead of looking for faults

Разрывная - раскинул мозгами Штирлиц

Onde adquirir um desse?

That is dangerous and stupid

Slt?

Yeah so safe

Nubs McGillicuddy

Dove lo trovo

La forma más rápida de quedarse sin dedo

I need to get me one of those. I got a bunch of dull drillbits.

У меня дед так стриг ногти!😂

Передоз, по-моему!

Дизлайк, так нельзя затачивать свёрла. Купите новое сверло и посмотрите внимательно какой профиль режущей кромки сверла .

Where do you buy one

malisimo

1- this disque is not done for that. 2- The temperature is too hot and the steel is not hard antmore 3- In a drill there are 2 angles and this only set 1 angle.

Bro did one grind and called it good... My machinig teacher would have erupted in front of the whole class.

Где найти? такую штуку. Точить. свёрла.

Ага щас 😂

Господи да нахрена что-то выдумывать? Чо никого деды в гаражах не учили как точить сверла на обычном точиле, без всякой этой херни, с годами на глазок выходит отлично и гораздо быстрее чем этот огород городить из болгарки 😅

Сверло не прокручивали, а заточка полукруглая😂

yeah lets start off by not using an angle grinder for that purpose 🤡

Where you been all my life?!!!

How to get it? Where?

Cutting disk gonna turn to shrapnel

Drill bit Guaranteed to cut from only one side...If you survive the disc fragmentation....Do you feel Lucky ???

Nome disso é?

Пример , как не нужно делать !

I have 21 stitches from one of those disc. Very dangerous tool.

Como se llama el producto?

На это можно смотреть вечно 😂

💰💰💰

En donde se consigue ese producto

Um peido, e ele perde esse dedão!

I've used a cutting disc to lightly grind things before like this. I see people in the comments talking about it exploding It can if you sideload the shit out of it but this isn't that bad and that product looks pretty cool

Nice idea, but... After a while, even though it's reinforced, that cutting wheel is going to fly apart. At 8,000 RPM on a 4.5" cutting wheel, that edge is moving about 107 mph. It'll be spectacular.

As a Toolmaker . Shhh , I've done this drill guide free . Hope it takes off for ya . Good luck .