Dehydration pinch test
0:45
8 жыл бұрын
Chevy Equinox AC Condenser Tip 2011
4:24
Clothes dryer bad timer cheap fix
2:10
Пікірлер
@EzziEllis
@EzziEllis 12 күн бұрын
Aeh I have that same noise on my 01 Mustang can you fix the knocking noise completely after you put nails in
@EzziEllis
@EzziEllis 12 күн бұрын
So the knockin noise is usually that area on the bar and poke holes with a long nail screw
@123tylerwetzel
@123tylerwetzel 15 күн бұрын
Amazing! I'm trying this out soon for my 93 corolla thank you so much for sharing your wisdom! 🙏
@itsgetnugly
@itsgetnugly Ай бұрын
I was of course skeptical about this idea, tried it on front left and right wheel bearing...heated both new steering knuckles to 450 for 2 hours and froze the new bearings for 4 hours. The bearings fell into the knuckle without a hammer! Genius and thanks a lot!
@scubadoonorway4960
@scubadoonorway4960 2 ай бұрын
I have thinking this must bee the best thing to do shall try next time..😊
@sasacata
@sasacata 2 ай бұрын
Is that 450 Fahrenheit or Celsius?
@Will_JC
@Will_JC 4 ай бұрын
@DustyRusty You didn't answer my request at that other video, so I'll ask again here: *Are you okay with emailing me? I want to talk about something privately, but if you're uncomfortable with emailing, I have a NON-email option you can consider.*
@biosphere8488
@biosphere8488 4 ай бұрын
What does freezing the bearing do?
@RockeyDAproductions
@RockeyDAproductions 9 ай бұрын
how did you get old one out?
@keithsharratt3402
@keithsharratt3402 10 ай бұрын
Weap hole.
@Susanne-u7m
@Susanne-u7m 11 ай бұрын
Thanks!!
@chrisdavis9144
@chrisdavis9144 11 ай бұрын
Thanks this video helped me out halfway of what i needed the other half is how to hook it up to a fuel rail on a 2000 ford ranger
@renealamo899
@renealamo899 11 ай бұрын
I'm considering purchasing a Yukon Denali 6.2L, is it possible to remove this filter and route an external oil filter/catch can to replace it?
@craiggerlach5548
@craiggerlach5548 Жыл бұрын
So the 01 4.8s have no filter? Trying to diagnose a faulty AFM system and it having shut off 4 cylinders and them not turning back on, and codes were just for misfires, all cylinders and MAF, and there was nest in filter box so likely why that code. You can hear those lifters clattering and runs on 4 cylinders like a dog... was running fine, no issues, good oil pressure, then went into this mode with 4 dead cylinders and flooding my crankcase with gas since it thinks those 4 are still running...
@xploration1437
@xploration1437 Жыл бұрын
This is an absolutely terrible idea.
@toddboone3923
@toddboone3923 Жыл бұрын
You have some really good ideas. 👍
@jamesrobert782
@jamesrobert782 Жыл бұрын
This also goes for the 4.3 engine in the chevy blazer, Astro van. If it's damp or rainy or humidity, car will stall out while driving and take a while to start backup. Very aggravating.
@andyp9131
@andyp9131 Жыл бұрын
Did this around 6 years ago to my garden furniture it brings the oils to the top u can use a heat gun as well
@jayhuff239
@jayhuff239 Жыл бұрын
Jeez! You can't be serious. Wood screws in the suspension? Just replace the bushings for crying out loud. One hour of work and $20.
@rahoffman123
@rahoffman123 Жыл бұрын
What about headlights does this torch work im wondering
@austinbrookes8017
@austinbrookes8017 Жыл бұрын
for the love of god, debur those edges lol
@sphinxattrasic4608
@sphinxattrasic4608 Жыл бұрын
Work smarter not harder dangit lol
@DKSE123
@DKSE123 Жыл бұрын
I did my timing belt 2 years ago , and asked you a question. I never heard a response? Are you even reading your messages ? Am I supposed to guess the answer ?
@justinreid8851
@justinreid8851 2 жыл бұрын
Do you know how tight to make that bolt when reinstalling the oil valve lifter filter screen? It looks like a manual trans drain plug to me. thanks
@yuhlimirfranzhiskje9143
@yuhlimirfranzhiskje9143 2 жыл бұрын
My skin doesn't come back at all.
@anguslean4058
@anguslean4058 2 жыл бұрын
The heat pulls the oils to the surface It dose t last long And the plastic is even more dried out then before
@hemojr
@hemojr 2 жыл бұрын
The pinch test is not an accurate test. The capillary nail refill test is.
@elyjahthomas9938
@elyjahthomas9938 2 жыл бұрын
The torch definitely works better then the heat guns I've seen
@mehmettln3524
@mehmettln3524 2 жыл бұрын
Can i apply to different colored parts?
@matthewhorobin492
@matthewhorobin492 2 жыл бұрын
Have you tried this process on plastic headlights In theory it should work similarly
@04dram04
@04dram04 2 жыл бұрын
I prefer Dulpicolor plastic trim black paint. It gives it a deep wet black plastic look
@mrpistonrecaro6483
@mrpistonrecaro6483 2 жыл бұрын
Will come off 🤷🏽‍♂️
@04dram04
@04dram04 2 жыл бұрын
@@mrpistonrecaro6483 Mine hasn't in years. its paint
@Adam666...
@Adam666... Жыл бұрын
You had me at deep, wet and black
@bus-fun-addict
@bus-fun-addict 4 ай бұрын
Yuk
@lewisellis7608
@lewisellis7608 2 жыл бұрын
well said😀
@vvalasek
@vvalasek 2 жыл бұрын
Great idea, can you also just grease the bushings on the sway bar
@kevinshea5819
@kevinshea5819 2 жыл бұрын
3:03 Boom is right
@tufaznail
@tufaznail 2 жыл бұрын
HOW LONG DID IT HOLD UP?
@snakeraji8784
@snakeraji8784 2 жыл бұрын
What is that rubber part called, a bushing?
@gapingtonbobuah9299
@gapingtonbobuah9299 2 жыл бұрын
Wonder if he will be posting videos from the burn unit ? Jesus…..
@danglez7022
@danglez7022 2 жыл бұрын
Or you can just use a heat gun its safer
@nocapjay3662
@nocapjay3662 2 жыл бұрын
I’ve been working on my bearing for two fucking days and here you go two seconds it’s in there you my hero man
@roypeterson5430
@roypeterson5430 3 жыл бұрын
if you don't wanna accidentally ruin your plastic just leave your car outside on a hot day then put a coat of transmission fluid on, let sit an hour or so then wipe off with a clean rag. works great and will last up to a year.
@RobB-vz2vo
@RobB-vz2vo Жыл бұрын
This works well. I did this on an old SAAB about 10 years ago which had plenty of UV-damaged plastic after noticing that a spot which I spilled some ATF on still looked good after a couple of months. So I wiped ATF on all of the UV-damaged plastic and rubber. The car sat in the Australian sun which has the highest UV levels in the world at temperature of up to mid 40 celcius (that's up to 105F); it still looked good after about 10 months which is when I sold the car. Just don't do what I did and wipe it on the dash because the oil seemed to evaporate and coat the inside of the windscreen with a fine oil and gave the interior the smell of eau-de-mancave.
@carbman007
@carbman007 3 жыл бұрын
Never knew this worked. I borrowed a bearing removal/installer that was crossthreaded and useless so was forced to find an alternative and sure enough it worked. I Put the part in my bbq grill and froze the bearing for only 5 hours and pushed right in. Thanks so much for this video.
@markmarcus3187
@markmarcus3187 3 жыл бұрын
How long it will last
@gioflores96
@gioflores96 3 жыл бұрын
I heard this is only a temporary fix, how long does it last?
@rusty15353
@rusty15353 3 жыл бұрын
Been 3 years on wife's Jeep still looks great.
@blackforestbear5132
@blackforestbear5132 3 жыл бұрын
it works better if u paint it with old oil and without heat 😉
@seeharvester
@seeharvester 2 жыл бұрын
Good & greasy, Nice & easy.
@botabingbottaboom2329
@botabingbottaboom2329 3 жыл бұрын
Does that heat separate the glue from the trim and car
@luvthqflex
@luvthqflex 3 жыл бұрын
No it will not but if you do go too slow it will burn the plastic, and possibly separate the glue from the trim and the car as well.
@shun3955
@shun3955 3 жыл бұрын
How long does it last?
@rusty15353
@rusty15353 3 жыл бұрын
Years, if you coat it with Wipe New Trim Restore every 2 years. I torched my wife's Jeep 5 or 6 years ago and it still looks like I did it yesterday. Follow my directions on torching carefully ok?
@shun3955
@shun3955 3 жыл бұрын
Well now it makes since thanks
@damygeebo
@damygeebo 3 жыл бұрын
lol, wtfff...this reminds me of the windshield wiper 'fix' where you tie strings to them and just pull them back and forth while driving down the road in a rain storm.
@FernandoMartinez-wf4jd
@FernandoMartinez-wf4jd 3 жыл бұрын
It's looks like a magic
@roxasparks
@roxasparks 3 жыл бұрын
Bro ingenious idea... but this crankshaft bolt will not break free
@rusty15353
@rusty15353 3 жыл бұрын
Yeah of course this wont-work for a crankshaft/harmonic balancer bolt. You'll need an impact gun or flywheel/flexplate lock and a big breaker bar. Those bolts are torqued anywhere from 150 to over 300 lbs
@roxasparks
@roxasparks 3 жыл бұрын
@@rusty15353 as ive learned... XD the breakers i have wont break em, and I dont wanna drop 200 on the 1/4 inch impact right now.
@johnmac3931
@johnmac3931 3 жыл бұрын
throw some cold water on it before it dries and it will stay shiny otherwise it will go dull again
@tahazouitina64
@tahazouitina64 2 жыл бұрын
are you sure that this method will work because i want to try it but i'm afraid please answer
@gogreen1963
@gogreen1963 2 жыл бұрын
Before it "dries"? Are we talking about the same video?
@zoezzzarko1117
@zoezzzarko1117 Жыл бұрын
kzbin.info/www/bejne/r3LYkHWPjayFZ7s
@generally.speaking
@generally.speaking 5 ай бұрын
Trying to break the plastic?