I have a lift and it worked this way…. I believe it only works this way if you have a lift.
@donaldgeter7657Ай бұрын
Damn did you have your axle replaced before?
@555mainesmonstersАй бұрын
Well, I’m about to start this job right now so wish me luck it’s 5:30 PM to see if I can get it done in two hours
@Carguy-fn5nfАй бұрын
Update?
@MrdubombАй бұрын
How did you get the starter heat shield out and back in without destroying it?
@79ramirez79Ай бұрын
@Mrdubomb it was tite but a little finesse so it could be reused
@DIYDON2 ай бұрын
i see 2 black wires coming off the potentiometer..1 gets spliced to the the green wire right..?..where does the other black wire go..?..if you could clarify that would be greatly appreciated as this is a great solution....thank you in advance....
@79ramirez792 ай бұрын
@DIYDON cut the green wire that leaves you with 2 greens now your interrupting the green so the 2 black of the potentiometer will go to the 2 greens
@EliasAbdallatif2 ай бұрын
Thank you so much your A hero
@giveme10feet4 ай бұрын
And you removed it from the FRONT of the truck instead of the REAR which would require you to remove the two coolant lines and plug them to keep them from leaking! Great vid, 'preciatechta!
@Litehousenation6 ай бұрын
lol
@jonathanTorres01037 ай бұрын
Great video! Big help had an issue w bike, was running fine one day and the next just gave out was trying to cut on but didn’t until I saw this video! Thank you!
@Scarymoviemaniac-youtube9 ай бұрын
This did not work for my 24v razor quad.. not sure why
@loens9011 ай бұрын
I just tried on my lx570 2009 and i had to take off the selenoid to fit in there and moving up the oil line for the tranny that pass by the oil pan i think the tundra and sequoia have a lil bit more room but at least you helped me still thanks?
@peteflynn Жыл бұрын
Would a 100k potentiometer work
@bean-matic9322 Жыл бұрын
on a 2014 tundra is it the same space in that spot bc i did everything you did up until that point bc it wouldn’t fit through, maybe i didn’t try long enough but i ended up loosening up the exhaust
@salvadorcuevas7998 Жыл бұрын
I do my just today thayou
@kye7018 Жыл бұрын
Tell grizzly hmu I met him at the lot today
@79ramirez79 Жыл бұрын
Haha will do
@bluefallon6374 Жыл бұрын
Well I didn’t see you take it out !
@karljohnson2864 Жыл бұрын
Does this truck have a lift or anything that would change the geometry between the A-arms and the CV axle¿
@79ramirez79 Жыл бұрын
Stock
@anthonyflores3540 Жыл бұрын
Mine still doesn’t start
@79ramirez79 Жыл бұрын
Crank no start could be a number of things this video is just for the obvious we miss on a Kayo quad....for your issue I'd check spark, fuel in carb,might have to bypass kill rope switch,or the red restart switch you cant always trust those electrical switches they do fail good luck
@victoralvarado557 Жыл бұрын
Clean the fuel lines I did on mine and works great I also cut off the switch with cap on itv
@jre69945 ай бұрын
@@79ramirez79any clue on why I change the motor and everthing and the quad cranks but don’t fire up I’ve changed everthing and I still can’t get it to fire up
@mikewest712 Жыл бұрын
this was not an oem starter. if you do this job, remove the engine mount and jack it up an inch.
@79ramirez79 Жыл бұрын
Yes it was an oem new starter better design and pricey
@martymartinez87932 жыл бұрын
Lol you didn’t have the solenoid attached to the starter
@79ramirez792 жыл бұрын
Starter solenoid is attached watch video closely
@travisj26952 жыл бұрын
kzbin.info/www/bejne/m5zVhn2qhMeVpJI
@isaiah-lava5.0862 жыл бұрын
Just did this whole job in less than 2 hours 🤑🤑
@dessicino1233 жыл бұрын
Thanks
@rrmarbleandgranite3 жыл бұрын
Thx we did this works great
@mattsivert25943 жыл бұрын
Damn that thing is clean
@ShutdownStranger5 жыл бұрын
For anyone who’s attempting to install one on a Razor dirt bike (MX400 in my case), I was able to splice a 5k ohm potentiometer in line with the green wire and it worked perfectly. I drilled into the grey fake motor and it protrudes from the side, under the shroud, so it is accessible, but not in a place where a kids knee would turn the power up or down accidentally. Speed is now completely variable. When turned down the kid will need to give a push off, as it won’t quite have the power to do it on its own.
@ShutdownStranger5 жыл бұрын
And if you’re looking to make this task as easy as possible and don’t mind spending slightly more, I found after the fact that electricscooterparts.com sells an adjuster that just snaps in between the two ends of the throttle plug (between the throttle and controller).
@staceyk25794 жыл бұрын
I need to try to put this on the razor mop
@albread5 жыл бұрын
Can it work with a razor go cart?
@79ramirez795 жыл бұрын
If the parts are the same out should
@albread5 жыл бұрын
79ramirez79 I think they are all the same. May be different volts in battery. Did solder the wires to the speed reducer ?
@79ramirez795 жыл бұрын
Try it out
@albread5 жыл бұрын
79ramirez79 how did you attached the wire to the reducer.
@79ramirez795 жыл бұрын
@@albread solder works best
@albread5 жыл бұрын
Did you solder the wires to the speed reduce. Then splice the wires to the green throttle wire?
@79ramirez793 жыл бұрын
Yes
@ricqik5 жыл бұрын
My starter didn't fit this way either. Maybe it's different starters.
@cutlerscrew64 жыл бұрын
Same. My starter from the dealership will not fit like this. But geez I wish it did !
@scotg37985 жыл бұрын
Cheers dude. Would a 10k potentiometer work?
@79ramirez795 жыл бұрын
scot g it should
@johngalvan22636 жыл бұрын
I literally just changed my boss starter thanks to your video he thought I had to take off alot of stuff thankyou
@javip26726 жыл бұрын
damn it's about time someone shows how to get to it the right way. under the car not under the hood. easiest way to replace...
@mrcoasttime216 жыл бұрын
YOUR AWESOME!!!
@valisapps12546 жыл бұрын
That's exactly what I needed , thanks for sharing .
@79ramirez796 жыл бұрын
Valisapps I'm glad it helped you out
@valisapps12546 жыл бұрын
79ramirez79 have you added reverse by any chance ?
@79ramirez796 жыл бұрын
Valisapps no i haven't but all you'll have to do is get a switch with 6 terminals so you can reverse polarity
@valisapps12546 жыл бұрын
79ramirez79 I've got one, but they have told me that it won't work because it's a 24v 10amp switch
@79ramirez796 жыл бұрын
Valisapps maybe 24 relays then
@skunkape18246 жыл бұрын
Mines a 5.7 ask my buddy u have to take cat out i got out finally thanks for you vid
@skunkape18246 жыл бұрын
My 08 tundra doesnt have enough room
@79ramirez796 жыл бұрын
Bryant Poe 🤔hmmmm maybe 08 is different ... the old starter was tight getting out the new replacement from dealer is wayyy smaller to make job easier but cost about 350 for it
@gringrinny90126 жыл бұрын
79ramirez79 no go on a 2010, 4x4... no where near to be able to remove through the a arm like in this video... tomorrow i'll pull out part of muffler, exhaust manifold will stay intact...
@xlilnetx2 жыл бұрын
It’s because he has a simple 2wd, everyone else he’s talking about has a 4x4 lol
@luckyrover54542 жыл бұрын
I’m four afternoons in. Still can’t get passed the transmission lines. Coolant lines are off still no go.
@79ramirez79 Жыл бұрын
Xlilnetx video shows the front cv axle which would make it a 4x4
@oldschool62686 жыл бұрын
Thanks bro !
@79ramirez796 жыл бұрын
Old school no problem i hope it helped
@Whyus7934 жыл бұрын
How old is this video? That truck looks new for a 07' my 07' looks like hell underneath. My starter is still original.