Having this problem

Nice info! I’m in the middle of testing. Shooting 300 subs 220 grain suppressed 7.5 in Faxon 1/5T barrel. It cycles and feeds but with quick trigger pulls it doesn’t get enough gas to lock the bolt back. I have to the lightest buffer maxim defense makes and spring since it’s proprietary to the cqb stock. I realigned the gas block and it cycled better but I think I will try a new gas block and tube as the gas block seems to be out of spec like you said bc when I checked I am hitting some of the gas tube when I check with a drill bit.

Slide hammer might shock it out better.than prying it

Well done, sir!! Great info

Do the cuts in the friction ring have to line up for it to work properly?

The second rifle is a CVA with a Bergara barrel. CVA is very accommodating, but they replace it with the same stocks. They send new stocks with dura coat. It's a terrible product. I had browning replace a shotgun stock with that coating with a stock that doesn't have that product on the gun. BPI outdoors / CVA doesn't have options without that for the Apex. Frustrating!

I inherited a Parker Brothers VH 12 gauge shotgun from my Dad. The first firearm I ever fired.

Picked 1 of these at a gun show 290 dollars in very good condition best shotgun i have better than my fab arm

Did you ever sell the 44 mag international model?

Good troubleshooting!!! Good job sir.

How did you line up the gas holes between the gas block and the barrel?

A one hour trigger job according to the clock

Great Video - I Appreciate the work you put into these

Ruger says dry-firing the company’s 10/22 rifle will not damage it. Without the last round bolt hold-open device you will inevitably dry fire on an empty chamber once you run out of ammo.

Thx for the disassembly tip. I will make me a clip like that. I have six 10mms including one of these and handload for them. 10mm factory ammo leaves much to be desired, so the recoil of factory 10mm is often deceptively weak.

k

Hawak mAs ser

Bruh it was the fucking ammo this whole time😭

I had a similar issue, only it was the screw holding down the trigger guard causing the problem. The head was too big, blocking the thing from going back all the way.

that's so dumb... fixed mine with an xacto knife.

Really...I have also used a wooden dowel as mentioned , dropped a few drops of motor oil and tapped it rearward . Worked like a charm. I would never use a drill, one bad angle and you can ruin a firearm.

Are you still repairing carbines?

I ordered a nomad and when it came in, it was so tight it was super hard to close and the trigger pull was so heavy I could not fire it. I had to pull it apart and use 600 grit to reduce the width of the ejector to allow it to close. I turned out the hammer spring screw till I was able to cock and fire it. It was not fit hardly at all at the factory. I can't believe it made it out the door. . Funny thing is the trigger guard problem operated fine.

احسنت ❤❤❤❤ عالی بود دمت گرم ❤❤❤❤❤❤❤❤❤❤

The fact that you "have to" say pistol, is crazy to me...

❤matap ...

Good news thanks

Great info. I know this is an older video but do y'all know how to tell the difference between a gen 1 and gen 2 1873 Uberti Cattleman 45 ? I just picked one up and not sure. Thanks

Any 2A win is a great win even on a a novelty item! Woot

👍

هل صحيح يطلق ثلاث انواع من الرصاص..مكاروف..٩ القصير..٧ملم..ارجو الرد مع الشكر

My grandfather used to say by golly all the time. Thanks for bringing back that memory!

I am having a problem with the safety not engaging and the trigger not returning but when I removed the slide that spring is still in place so I'm not sure if that's the culprit I was shooting today and the trigger didn't return after cycling

Thank you Sir. Very helpful video.

your camera was on wrong setting ....like a curved view

Very helpful !! Thank you 🙏 !!

Had to drill mine with 7/64 flawless Ty

HELP WANTED. My A5 16ga will not extract modern plastic star-crimped shells. They open up too long to get out of the port. Has anyone sourced paper roll-crimped shells or figured out a way to trim the plastic shells and reload? Thanks for any advice.

Mine is .22 mag/20g. These are sought after where I am in Canada and very expensive. Very well made firearm.

Finally got to the point...

Sometimes it is better not to see how the sausage is made.

when I bought mine I replaced the factory trigger with a timney set at 3lbs then replaced the internal mag with a box magazine, it is now a suberb hunting rifle. love it.

Ive tried taking the bullet out of a cartridge and shooting it to blow squibs out of barrels and its worked everytime. I saw it on a video and was very skeptical. But .....

You made me so happy to see a professional struggle getting that sear block assembly in place. It drove me crazy for about 2 hours. Great video. How about showing us how to reassemble the magazine disconnect lever with the torsion spring. I could not get that done so no more magazine safety for me😮

Have. One as a deer gun it’s the best !! Also my skeet gun it’s a awsome shotgun !!

Some people have no business working on rifles. This is embarrassing

My drilling buggered up the barrel.

I lube the inside of the barrel before i start trying to pull the bullet. It sure helps/

Good teacher

Oddly enough what fixed my issues with this was to put in larue tactical power extractor, and change out buffer to an h1 and change the buffer spring back down to a milspec carbine, and voila. This is 556/223 not 300 BO but had the exact same issues u had here. The thought did cross my mind a few times of drilling out gas port bigger and just as I was about to do that everything started cycling