High watched your video i have brickwell controller like the one you tested works ok but when i turn it of fans will not kool it down just shuts everything off i need help if you can thanks
@brooklyn_autumn20 күн бұрын
My daughter just got the King Ashley 5500m and everything works great but the Auger isht feeding enough pellets to keep not going. Zero option for it to dump more pellets arva time to keep it fully going. Eventually burning out and shutting down. No thimb screw to adjust on the inside where the auger is inside the hopper. Ivevtryed different heat settings (keeping the blower 1 above the heat setting) Anyone have a solution?
@javiermunoz376425 күн бұрын
Need your phone I have some problem
@MonteStudios25 күн бұрын
@@javiermunoz3764 971-724-4115
@toddschroeder1757Ай бұрын
please send me by email... I have 2 or control board of acutron iv...both need repair .... one is igrintor not get hot even light on control board is on... and other is it shut down no light after i turn on and then i have to turn on again and now it running
@IIIgemini2 ай бұрын
Hello, I have a very similar chain hoist and we're replacing the chain. Can you tell me how to re-thread the chain into the unit?
@MonteStudios2 ай бұрын
@@IIIgemini cool chain hoist.. sorry, but I sold that unit years ago.is the old chain still in it.
@Rooster61612 ай бұрын
I have an sm160 IQ5 board that needs repairs. Would you be able to do this?
@MonteStudios2 ай бұрын
@Rooster6161 I have previously repaired two different units of SM160 - IQ-5. You can fine post repair videos of these two in my CookShack repairs playlist. That playlist can be found here for you to review: kzbin.info/aero/PLXLzfNF2AmoBMJl3wkfl-CnpHDGuIf_pw
@MonteStudios2 ай бұрын
@Rooster6161 I would be more than happy to further discuss trying to resolve your issues.. If you can, please test me at 971-724-4115 more details of the problem you are having, and I'll gladly respond that way.
@Travis35002 ай бұрын
One of the small screws stripped on the dang metal piece that screws the hoses into the side of the carb I’ve been debating just drilling it out and making a new hole but it’s a lot of work for this little 7.5
@beerdiaryshootinmcdaniel80633 ай бұрын
What is the point of this? My gc160 i am putting on generator head has a blocked off port here. Why did some use it?
@DavidDavis-on2fi5 ай бұрын
Does this super mustang have a dipstick because mine doesn't have to
@MonteStudios5 ай бұрын
No Dipstick... just a standard Briggs and Stratton oil cap. Double check, but I think that the manual for that engine call for just under one Quart of oil.
@grillnbam98216 ай бұрын
Thank you so much. You are amazing. I will send more people your way. 👊🏽
@MonteStudios6 ай бұрын
Thanks for the feedback. I appreciate it and your offer.
@Andi.Mitchell.DesignsАй бұрын
Hey. Grillin. Can you send me his info? My quadrafire control box needs help and his info page is private.
@DChame-jh6hl6 ай бұрын
Supposed to remove the back wheels.
@WyattStracener6 ай бұрын
How much factory time to Randy carburetor
@stevenmirman81157 ай бұрын
Interested in this repair, are you still doing them?
@MonteStudios7 ай бұрын
Hi.. Yes.. I still do such repairs.. let me know more about the symptoms your controller is giving you.
@JSG-vo7eh7 ай бұрын
please help i cannot get my brand new breckwell big E pellet stove to turn back on ran it for 2 hours, shut it off for a while (cold to the touch) turned it back on it ran for 3 seconds then nothing not even a light on my control panel ,no green blinking light, nothing
@JSG-vo7eh7 ай бұрын
just bought brand new breckwell Big E ran it for a few hours , shut it down now i tried to turn it back on hours later, a fan kicked on for 3 seconds and the auger put pellets in the tray then it shit off now i got no lights on control panel pls heklp
@miguelarias50007 ай бұрын
What mix do you use?
@lahaza65158 ай бұрын
WHY does NO ONE EVER go over which settings with which levels? I appreciate the video, but it's so frustrating. I've had mine for years and the man who sold it to me said the fan doesn't come on until it's hot enough. That's how my old Breckwell works anyway. I vacuum it out every few days in winter & keep it on setting 1 to save pellets & add to the oil heat, but it just went out after 15 min of startup and is blinking 3.
@BrianBerends-j7u8 ай бұрын
Do you still repair boards?
@MonteStudios8 ай бұрын
I still do, but.. for the AcuTrons, it really depends on what the symptoms are.. if it is DEAD, there is no bringing it back to life.
@BrianBerends-j7u8 ай бұрын
Igniter shorted the board path on the board. Everything still works except Igniter.
@BrianBerends-j7u8 ай бұрын
You available tomorrow? Don't wanna intrude. Give me a good time to call you.
@GraceTaylor-i6i8 ай бұрын
We have a Breckwell Series P24FS and are requesting help to possibly get it working again. We have used it for 22+ years and while replacing some items - the service person may have either messed up with the wiring or controller. If you can contact us that would be incredible. Any assistance would be appreciated. I cannot access website -
@kotayann42438 ай бұрын
@@MonteStudios I also need some assistance with my pellet stove, tried calling that number to communicate with you and it didn't work. Is there any other form of communication?
@privateassman88398 ай бұрын
Found one by the side of the road. Cracked and punched in mower deck, won't start. Gonna weld up the cracks and pound it with a hammer, then break the crankshaft nut off (if I have to) to remove and service the motor. 🤞
@MonteStudios8 ай бұрын
An impact wrench should easily remove the crankshaft nut.
@privateassman88398 ай бұрын
@@MonteStudios I think it's rust welded. I'll soak it in penetrating oil and blast it with a torch. I don't have an impact wrench, but I've tried an impact driver (it's snapped bolt heads off, so it's decently powerful) and it didn't break it.
@luciocastillo98168 ай бұрын
No lo puede esplicar en español
@jerrydavis38738 ай бұрын
I have a king 5502m control panel I would like to send to you. How do I go about that?
@MonteStudios8 ай бұрын
Here is my contact information... kzbin.info/www/bejne/qofRhoCCqtWVoqM
@MrAlaska669 ай бұрын
I have a USSC King 5500M pellet stove with this type of controller. Do you know if it can be easily updated with the newer style controller, or any more common controller?
@MonteStudios9 ай бұрын
I am not knowledgeable enough to answer your question correctly since I don't know exactly the type sensors in your stove and their requirements. I have not done this in the past.
@671mach9 ай бұрын
Thanks for the video! Do you know if this box will cycle the auger motor durning normal operation (once 1100 deg is reached)? I know some models do, but mine seems to run continuously once a call for heat is sent. Thanks again!
@MonteStudios9 ай бұрын
That model controller will not cycle the auger motor once the red light has come on. It drives the motor using a mechanical relay, and that relay would wear-out in no time doing cycling.
@671mach9 ай бұрын
I really like your added yellow led for the auger. Any chance of a "how to add this" description? My controller is an older "black" type out of a 1000. Thank you!
@671mach9 ай бұрын
super helpful, thanks for the video!!!!!!!
@671mach9 ай бұрын
One quick question just so I understand: in your video, when first putting power to the controller, the exhaust fan power light comes on as well as the convection fan light. The convection fan always has power and is switched on and off via a snap disk? When powered up initially, with no call for heat from the thermostat, the exhaust fan will run for 15 or so minutes and then shut off? Is this correct? In other words, the light for the exhaust fan would have gone (after 15 mins) out leaving only the convection fan light on. (in a power on but no cal for heat condition) Thank you!
@671mach9 ай бұрын
Can't thank you enough for this video. Now I understand exactly what the controller is doing and when which explains the issue I have been having with my stove. Thanks again!!!!
@davelowe-e9j9 ай бұрын
Not true if reset when burning. Stove shuts down shut blower off. Don't do when burning!
@AlpineWarren9 ай бұрын
I haven't heard of Breckwell but my local dealer carries them so we are looking at the Big E - What are you thoughts on their quality electronics-wise? Appreciated!
@str33tb1k3r9 ай бұрын
Have you ever seen an err11 code before?
@MonteStudios9 ай бұрын
I have not.. err9 is the highest I've seen.. I'll bet that it is not listed in your manual either. Contact USSC support to see if they can offer a clue on what the error means.
@thomasradlejr80059 ай бұрын
I have a american harvest 6100 had 2 questions 1. is there a corn setting and pellet setting that can be switched. 2. My heat range settings only go up to 3 is that normal or is way i can reset it. Thank u bought it used and still learning
@BloodBloon2310 ай бұрын
I have to press the power on button many times before the stove starts, doesn't feel like it presses in the same as the buttons? dirty switch ? can it be cleaned?
@MonteStudios10 ай бұрын
Fairly common problem.. replace the switch with a new one.
@ianb181610 ай бұрын
Promo sm 😃
@stevenrenshaw462310 ай бұрын
Fan just stopped, had been running fine, will not come back on, even after cooling off.
@MonteStudios10 ай бұрын
Which fan are you referring to? the Exhaust fan or the Combustion fan?
@XxKhao10 ай бұрын
I have an er9 on my king stove would u be able to help??
@MonteStudios10 ай бұрын
Yes.. just now that err9 is a component failure on the main controller board.
@XxKhao10 ай бұрын
@@MonteStudios I messaged the number in your video at first it wasn’t giving any codes wouldn’t turn on or do anything after unplugging and plugging back in got the er9 the stove is only a little over a year old
@edearl276910 ай бұрын
I have a Whitefield advantage ii-T control board that doesn't cycle threw auger mode. When you turn on auger motor switch the light goes dim and control board smells like it is getting hot. Unplugged auger motor and light turns on and stays on bright. I Checked the volts coming to the auger motor and it is around 86 volts all the time. Motor check out fine. Would you be Interested in repairing this for me?
@interestinoldschool808010 ай бұрын
Thank you for posting this video. I just picked up a used 23fs, which I am giving a test run in the garage before I pull the permit and install it in the basement for supplemental heat.
@matthewmutch785310 ай бұрын
Your the MAN!!! THANK YOU SO MUCH!!!
@louh947310 ай бұрын
Very well done. Thanks.
@adamnovielli116910 ай бұрын
Thank you so much for this great video. I’m wondering if you already answered this: I just replaced my exhaust blower fan. When I plug it into 120v outlet, the exhaust fan starts spinning immediately even with the control board switch in the off position. I am not sure how to fix this issue.
@MonteStudios10 ай бұрын
Hi Adam.. about our exhaust blower running all the time.. Can you share why you replaced the blower in the first place? When was the last time you knew it to be correct? For sure, the OFF switch on the control panel (lower right) should switch the fan power OFF and cause it to stop spinning. There are a number of components that can fail on the control board that can cause this to happen. You can call or TXT me at 971-724-4115 and we can discuss further.
@defconklaxon10 ай бұрын
What was the fix? Replacing relays, replacing relay drivers? Super cool test rig!
@dalewilson782010 ай бұрын
Very pleased with the service and turn around time for the repair.
@user-vu3qu7jt7s10 ай бұрын
I have a acutron 2 board that needs repaired. No power
@MonteStudios10 ай бұрын
Unfortunately, this is nothing but bad news for you...Those controllers are very fragile, ad NO Power indicates the the micro-controller has failed (typically killed by an electrical event). The is nothing I can do to repair units tat are completely dead. Sorry.
@deniellejugal931111 ай бұрын
Hello, our pellet stove is having a problem with its automatic feeder. Whenever we want to use our room heater we have to manually feed the stove to keep the heat going. Is there a way you could help us? Auger light indicator is working, combustion fan is also working. But the automatic feed is not.
@MonteStudios11 ай бұрын
Sounds like you have a failed electronic component in the Solid State Relay system. I can repair that.. Call or TXT me at 971-724-4115 and we can further discuss.
@brianmiller407611 ай бұрын
If I send you mine can u fix mine
@MonteStudios11 ай бұрын
Yes.. give me a call at 971-724-4115 and we can exchange information and problem statement.
@JohnGeorgia11 ай бұрын
What happens if it don't reset? I went to turn up the stove and it wouldn't go up I noticed a red light above the arrows I hit the off button and it won't start back up
@swoop-it462111 ай бұрын
Can you send me a pic of the rear? Need to see the with that’s connected to the thermostat switch
@richardnavarro591811 ай бұрын
hi, i didn't plug my hoist in after a year and now the chain does not move in any direction. Any idea what can be wrong? it does turn on and the remote only clicks, but no movement. Thank you in advance.
@MonteStudios11 ай бұрын
I have a couple of ideas for you... give me a call at 971-724-4115 - we can discuss.