3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
4 жыл бұрын
4 жыл бұрын
Пікірлер
@ryanalexis2 8 ай бұрын
Do you put the sub on the back so you don’t reverse the image?
@frankcurrentii6844 2 жыл бұрын
have you tried oracle 651 white vinyl? how would that be vs using the laminate and spray paint? May help take a step out of the process, but the colors may not be as vibrant.
@sweetfunkydesigns Жыл бұрын
No I have not, but I will try it when I make these again.
@Chsbobcat1 2 жыл бұрын
Hi! I might have an idea to help. I came across your video looking to see how difficult it would be to weed out a QR code. I noticed your coat had a lot of lines. If you put the code into TinyURL, it’ll turn the longer URL into a smaller URL which will create a less complicated QR code. And then you can take the tiny URL and move it into the same QR code generator to download the SVG. Hope this works/helps!
@sweetfunkydesigns 2 жыл бұрын
Great idea. Thanks. Didn’t think about that v
@ldesigns7790 2 жыл бұрын
How did you cut that qr code and was that an svg file?
@sweetfunkydesigns 2 жыл бұрын
I used a website to create a QR code and was able to download it as an svg. It’s a pain in the caboose to cut and weed.
@ldesigns7790 2 жыл бұрын
@@sweetfunkydesigns thank you for your response, it looks very time consuming.
@ldesigns7790 2 жыл бұрын
@@sweetfunkydesigns i know for htv it has to be mirrored, but cutting a qr code do you have to mirror it also?
@sweetfunkydesigns 2 жыл бұрын
@@ldesigns7790 it doesn’t have to be. This was not as I was placing it on the acrylic.
@darleneroach2848 3 жыл бұрын
Does your heat press cause your light bill to go up a lot, do you use your heatpress often? Thanks!!!
@sweetfunkydesigns Жыл бұрын
No not really. I don't think I press enough for that.
@chrisc7566 3 жыл бұрын
you can still use the design again. make it look even more vintage
@sweetfunkydesigns Жыл бұрын
Didn't think about that.
@brettlathrope3612 3 жыл бұрын
Really, I watched all that to not see how it was finished, or the final product? Come on girl! Also ... for the love of Mike, spend $10 on a heat glove.
@sweetfunkydesigns Жыл бұрын
Sorry. I thought I did.
@patriciacaro2145 3 жыл бұрын
What side of the laminate sheet do you put donw on the glass, shiny or dull?
@zootasplace7344 3 жыл бұрын
It does not matter, when heated it will be clear
@zootasplace7344 3 жыл бұрын
Sorry corrections: Put the dull side down as that is how the laminate would be if you were laminating paper.
@EyezofMoe 3 жыл бұрын
Usually those glass boards comes with the little rubbery “feet” thingies on the bottom. How do you get those out and I’m guessing they’re replaceable???
@sweetfunkydesigns 3 жыл бұрын
I just pulled off. I bought more from Amazon to use because sometimes all the glue doesn’t come off with the rubber feet. If I can reuse them I will.
@beainc3423 3 жыл бұрын
So the picture goes on the laminate side
@lgray10101 3 жыл бұрын
the laminate is made of polyester, so the sublimated print will adhere to that. yes, you lay the laminate shiny side up, place your image on teh shiny side of the laminate, the dull side of the laminate has the glue that will make it stick to the glass
@zootasplace7344 3 жыл бұрын
@@lgray10101 not totally true. There is no glue on laminate sheets. But my suggestion would be to put the dull side down because that is how it would be if you were laminating paper.
@lgray10101 3 жыл бұрын
@@zootasplace7344 dull side down equals shiny side up no? Same thing
@zootasplace7344 3 жыл бұрын
@@lgray10101 Not if you are saying it is glue. That was the part I was disagreeing with.
@jillbach4774 2 жыл бұрын
I am getting air bubbles between the laminating pouch and the glass. Any recommendations?
@mariatalavera8850 3 жыл бұрын
What side of the cutting board do you do? The smooth side or scaly side?
@sweetfunkydesigns 3 жыл бұрын
The back. Smooth side. You have to remove the little ‘feet’ first.
@beulahcarpenter133 3 жыл бұрын
What type of paint did you use n the back ?
@sweetfunkydesigns 3 жыл бұрын
Just rustoleum white spray paint
@shillongmixbag5280 3 жыл бұрын
Is it regular glass without any coating?
@sweetfunkydesigns 3 жыл бұрын
Just a dollar tree cutting board
@shillongmixbag5280 3 жыл бұрын
@@sweetfunkydesigns but we need polyester lamination sheet?
@sweetfunkydesigns 3 жыл бұрын
@@shillongmixbag5280 no. It’s just a regular lamination pouch. Pulled apart and use one side. You can pick up at Walmart or Amazon.
@Mamadukes2008 4 жыл бұрын
It looks like you have some kind of protractor on the side.. is that something you added yourself? I have a francier studio heat press and I dont have one of those. Also, does that help you with figuring out your pressure?
@sweetfunkydesigns 3 жыл бұрын
That’s a laser level for when I do shirts. That way I can make sure things line up right
@carolynwilmouth8593 4 жыл бұрын
Did you spray paint the back or use chalk paint?
@sweetfunkydesigns 3 жыл бұрын
Spray painted white
@eddiegonzales1530 4 жыл бұрын
What’s the average setting you use when setting the laminated sheet onto the glass I saw 365 @60 correct?
@sweetfunkydesigns 3 жыл бұрын
That’s what I did.