Riley sudah di ganti tapi masih ada help bagaimana.?

Good thorough work

👍👍👍

EEVs have to rotate instead of being pushed/pulled. Use a segmented magnet It will rotate to EEV valve core when turned. Amazon carries them. It may work if you take one or more of those doughnut magnets and break them into semi-circles and put them back together.. One end becomes north and the other will be south.

What brand is that magnet pls, daiken sells theirs for 600$ wtf

That ice machine was spotless ,

I just got a brand new commercial pizza oven a couple days ago. When I was testing it and tried to make a couple pizzas, it kept turning itself off when it got to 650 degrees. I suspected that it might be the thermocouple, but I don't have a voltmeter - so I just looked at it and made sure it was clean and positioned in the center of the pilot flame. I just finished testing it again, and it's working great now. I suspect that the thermocouple might have been moving out of the pilot flame as the oven heated up and everything expanded.

Great Video Dave!! It's good to see one of our older models still getting it done. Keep up the great work and never hesitate to call our customer service team. Kris Witteveen, AbsolutAire, Inc.

I like checking for 24v on X. You know right away it's in lockout.

What size pulley is that and where do I get those h bushings

thanks bro veryhelpfull. imso technician. SilverWorkSporTv yt

Bro keep making these vids, especially the restaurants reach in coolers and freezers that is so niche that i think you can grow quick. Commenting dor your algorithm

Thank you for the video. How do you install one of these bin stat? I have to do a installation and can't find it anywhere. Thank you for your response

How do you put it back on?

This is not the case in every brand contactor. In the new ones I have, there is no way to convert it like you did. You should have said YMMV to be more accurate.

How much should this job cost ?

Did he say he had to jump off a binswitch to another binswitch?

Okay so I have a client that had a small grease fire in the kitchen and the ansul and sprinklers went off and one of their breakers won’t turn back on, guessing it’s a shunt? They have a weird frame covering the dead front, I have dealt with Siemens load centers a million times but I literally can’t figure out how to get inside the panel

Good job 👍

thank you for no annoying music. I hope your channel does well

Why not just rub the marker on it?

Now that's a winner of an idea!

The bushing got a grub screw holding it onto shaft?

How do you get a Retrofit kit for going from the lens to flame rod?

Brother I can’t even figure out how to get the fucking blower compartment open the latches don’t do shit

Ya that design sucks. Always issues with freezeups

Thank you for a good video :) Few questions, my pump is leaking from the shaft seal. What is the correct size of the seal and how do you remove the old seal and put new one in? Also, at the same time the o ring to the back cover should be changed. Do you know what size is the back cover o ring? One more, the pump motor is seized, it 's full of hardened grease. How does one remove the pump motor? The electric connections?

Damn 77💀💀💀

Love the energy man🔥😂

Are you using a standard cat 5 or cat 6 cable between the vfd and screen?

I didn't know what direction the air was moving just from the video but "some guy just replaced a thermostat and it isn't working now" usually means "the thermostat was not installed correctly". That and the bulb seemed out of place.

Are you checking micro amps for flame rect?

Hey sir I have a issue with the same fryer but only 2 tanks. How ever it keeps making a loud popping noise. I changed out blower motor and relay as well. What else can it be ??? Pls help

Just what i was looking for! Thank you.

Great refresher More please and thank you sir!

Wow thats an old unit still high tech for some back them

Thanks for the info My drain limit switch was faulty

My y600 oven stopped heating up in the middle of dinner,the pilot is still on but no flame? Please help

Thank you

Life saver thx

No way!!! What??? I'll check this out definitely

At first I was skeptical reverse wiring the polarity of the motor. After trying to get the backside of the impeller motor off (with no avail). To spin the shaft, we decided to have staff empty the vatts so we could undertake the nasty job of pulling the motor. We ran across your video and said-what the hell, we will give this a whirl as the wires were accessible through the access panel on the front of the motor. After reversing the wires and a few quick on-offs! Viola!!!! The impeller freed up and we are back in business! Thank you so much for posting this detailed video.

Forced draft

As a new hvac/r tech thanks my dude

Thank you, got this unit working after watching this ! 🙏

Thanks for the help! Do you know what kind of power opens the combination valve?

keep a empty bottle in your bag😂.

Bet unit is more problematic now tho

Just want to express my gratitude for this video that you put up. Had to replace the gearbox assembly last Friday, and I've never done one before. Thanks to this video i was able to swap it out and get it running again. Once again, thank you.

Excellent very very helpful thank's and a great site by the way...good humour and fun.