Hey thanks for watching! With your issue I would recommend to first check the connections to the actuator and make sure it’s not shorting to ground causing that issue. Make sure the connections are not corroded and tight.

Hey 1 amp diodes are good enough

Im not sure but i would check any bolt hole that has a long standoff . Like on the cover it not close to the mating surface of the cover the to the engine block. Good luck

No they were all junk broken on the inside and I don’t like chrome

3/8 lines

I have a cable hooked up in a secret location that will open the door if the battery dies. I have 2 batteries and I can get to the other one without opening the hood also. I also have a safety switch installed for if I were to lock the keys in the truck.

Over 200k

@DinasGarage thank you. My 93 d21 has 154,000. Just starting to have ignition problems. Aftermarket parts are sketchy. I'm replacing the distributor; I hope it solves my problem. 😬

Thanks for watching!

Thanks for watching and asking! So my chain was rattling at startups and I had to reseal the oil pan when I pulled the oil pan I found the plastic chain guides s broken in little pieces in the oil pan. So I decided it was time to change the chain. For a no start condition, check to make sure you have spark first, then make sure your fuel is reaching the injectors. If those are all good then more diagnostic will be needed.

Thanks for watching! Because I didn’t want to make a huge mess under my truck..

​@@DinasGarage Well everyone knows if you don't want a mess at you're house take it to you're local autozone parking lot and do it there. haha!

No I used priority unlock for the drivers door and press the unlock button 2 times for the passengers door!

@@DinasGarage sweet. So main unlock wire to driver and which wire from compustar is the wire that only works with 2 press of unlock button

No you have to program the brain to one of the POC’s to be a priority unlock and the normal wire for unlock to the passenger door

@@DinasGarage perfect. So one press will unlock drivers door and of pressed twice it will only unlock passenger correct?

Yes SiR

I don’t have the repair manual to give out sorry thanks for watching

distributor gear backwards?

I came hete to see which way it goes as I'm reassembling mine rn and noticed it's the opposite way as it was removed in 1st video lol

😂 😂 😂 😂 😂 😂 😂

I’m gonna be down in your area on the 10th of February.. picking up another…

I don’t know I do not have a serpentine belt on my KA24

Thanks its a 95 Hardbody Kingcab

Glad it helped 🫡

Did you try to pair them up with the brain of the system? What brand are you using?

20 gauge, I believe they would fit.

Yes and no the noise was more pronounced when stopped and the clutch pedal pushed in..

Thanks for watching!! Yes it is.

@@DinasGarage appreciate it!

Hey brother, I have 225/45/17 I had to cut the inner fenders so it can lay out. I’m 48 going on 49 in April. I’m glad you’re back on your channel I was missing your content…

@shortsbbq thanks for the comment! I’m an old man and I worked as a technician for over 15 years after I got out of the Army and went to Desert Storm. I have always wanted a mini truck since I was 14 and now that my kids are grown it’s easier for me to do this… I have a hard time filming by myself and I have a degree from a university. I’m not uneducated… but I am learning a lot on my own from doing my mini trucks. I have bagged a few S10’s and the Nissan is my first torsion bar truck.. he just talks a lot more than me.. 45 min video and most of it is talking… he welded up a turbo for his neighbor? How’s that a part of the video? It’s not if the video is about body dropping the truck… I know how to body drop untraditional which just takes to raise the cab and cut the top of the frame off then install a strong box tubing into the frame and welding it up… traditional body drops lose head space and feet space and makes the truck cramp.. with us being older it’s hard and more painful to get into and out of a traditional body drop.. I figured he would do that because of the lack of space you get in a traditional body drop truck.. I’m not offended again.. I really appreciate you coming over and commenting on my video.. keep on Minitruckin! Brother! 🙏🏼🫡

Thanks brother! Really appreciate it! I still got the back to do and then raise the bed floor.

I bought a tensioner from Martin Industries because the first chain I had did make noise. I purchased all the timing components from Nissan as the Aftermarket one I had , the chain was 1 link too long which caused the issues. Along with fighting the distributor and oil pump alignment. www.martin-industries.net/product-page/nissan-ka24e-self-adjusting-tensioner

Including the chain guides?

You can get them from Nissan still i believe

@@DinasGarage thanks 👍