Thanks. Helpful video, but dunno how you got screws in so easy. The screws are such bad quality that they strip when I breathe on them, so 50% don't make it in the hole as they're mis-shapen. So frustrating!

What no expansion joints on floor, heading for disaster, not the best instruction video on line by a long way

Thank you your video is the only one that shows the montage up to the doors where I didn’t know how to do it.//Merci à vous votre vidéo est la seule qui montre le montage jusqu'aux portes ou je ne savais pas comment faire.

10mm spanner was unavailable probably… and get the correct bit for those bolts so you aren’t stripping them 🙄🙄

Looks like paper house. Very unstable

I am literally about to go out the garden and build a 10ft by 8ft one of these right now. I will say that you should strip the plastic wrap from the parts days before you do the build, because it takes a very long time (3 and half hours for me solo). I'm going to build the shed on my own. Have made simple scaffold pieces from spare timber with magnets to hold the walls in place. Looks like the issue I'll have is holding the nuts on the back side of the wall. Why they don't use a socket to hold the nuts in the vid I don't know lol

How is water stopped from getting underneath around edges, then sitting and cause it damp/rot for wooden base panels?

Wow❤❤❤

We order soon❤❤❤

Soon we buy for my bathroom❤❤❤

Looks a bit flimsy for "Glazing"! I know it's not meant to be glass but even thin perspex would be sturdier wouldn't it. Is it because the wood expands maybe?

Nice video! Excellent. It its enough 4 cm concrete base?

The door do not have lock? Is it safe?

I’ve just done one of these and what a nightmare working from the manual, I’ve completed it and all is fine until I close the doors! There is a gap at the bottom, if I hold them closed all is fine, and I guess if a padlock is in place all is ok, depending on the type of padlock, any suggestions?

You guys saved my ass. And prob my wedding😂😂😂

I really cannot begin to explain just how helpful this was whilst putting up my dad's shed. Thank you so much

Chines ... beeep ...beeeep ....beeep :D

Thanks guys

anyone else had issues with the back and side wall panels? Each panel has like a flat edge and a cornered edge so the one can overlap the other and prevent water coming in. There is no other way to mount them on the base frame bc of the predrilled holes. So now the back side has flat edges on both back panels, and the side panels both have cornered edges. For the side panels it doesnt matter but for the back you now have to connect 2 panels on that flat edge and thus water can come in. its just stupid!

How do the shed walls fix to the bottom of the body? I have the small shed with log storage and I don't know how the side panels attach to the bottom

Само вятъра ме притеснява, че това нещо изглежда толкова леко, че не знам какво би я задържал на земята

A good idea I found was to dab a little grease on the runners if the adjacent old boards have swollen - they'll go in much easier.

Make sure not to what?

Thank you for showing the first step from the bearers not many people do.

UNA MIERDECILLA DE CASETA.

Why can't you fit the floor frame before erecting the out pieces?

Broken

Narrator says 'make sure the nails go though both the layers', guy on roof 'meh I'll just put them through one layer at the top'.

Thanks for the tutorial, much better than the silent one with the canned folk music. I like the way you used the needle noses to hold the nut. If only someone would invent a tool specifically for that purpose...... A sort of screwdriver for nuts or "nut-driver" (for lack of a better word) 😅

Thank you for making this video, we.d still be tryna build the shed (from another seller) the instructions were hopeless

For me, the ideas in kzbin.infoUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.

Is the slightly raised OSB boards sufficient to prevent condensation inside the shed due to the concrete underneath being wet, presumably not having a Damp Proof Membrane underneath? Also worth pointing out that the base should be sealed along the bottom (before fixing to the concrete) to prevent water seeping in at the bottom

Anyone know where I can order the plastic corner connectors?

Thank you for the great instructions. A complete lifesaver!

Cracking video, and a good storage shed as well. Thanks

Magnifico video. Tengo que montar una caseta casi igual y sus explicaciones serán de gran ayuda. Muchas gracias

Why you building it on grass wtf 🤣🤣

It needs more stability and screwed to the ground . A gust of wind will take it out .robbery

I ordered a 4x6 shed. It only measured 4x5. the metal is so thin. very disappointed with this shed

Thx u so much, I am having a hard time with the beams, I'ma keep watching until I get it

Nice

I guess it’s good to have a go.

Those panel are so thin they bend when put screws, so much bad quality and not support at the middle for bad weather

That looks like it would be easier to get the avengers to assemble 😬

Bonjour, merci pour cette vidéo qui m'a bien aidé ! 🙂

You've posted a truncated video...

I will advised you please don’t do it you will be disappointed ☹️ if you can return it do it as fast as you can this product is nothing but garbage 🗑 I’m very handy when it comes to problems like this shed main problem should be done with one person no two but the engineers never thought about this little issue so the rest of problems are due to lock of imagination

Just wondering if I can use a piece of chipboard word or something similar as the base as I don't have a concrete base just compacted stone.

In practice if anyone has a damaged board, I bet they won't be any to find a replacement the same size.

I really appreciate this video tutorial. The instruction book, other videos and this one was great! Thanks for sharing it.