this is very useful because you dont have to solder anything directly to the phone and still can use battery when needed
@zodiacfml10 ай бұрын
thanks!!!
@expression3639 Жыл бұрын
lol it's not "without battery" if you solder battery cells to it.
@BaxtiyorShodiyev-ks9vd Жыл бұрын
Yaxshirogʻi yoʻqmi😢
@seegobinpersaud3112 Жыл бұрын
Cook
@onoaquino29492 жыл бұрын
kzbin.info/www/bejne/rnOqdKqPpsychNE How did you come up with the correct conclusion about the correct polarity of the battery circuit protection? You just showed us that those were the negative terminal and the positive terminal without telling us how you found those out. I would like to use 18650 batteries too for my old phone, but without your explanation, I might get 50% incorrect in guessing the polarity of the terminals. Please enlighten me. Thank you!
@sunmugarasa13192 жыл бұрын
More smart mobile hacks
@mahbubalam65652 жыл бұрын
Very fine!!!
@prentisboy20192 жыл бұрын
I got some questions
@mathematicsclassesbyrkshar89933 жыл бұрын
Lumia 535 mere pas bhi hai purana
@gameonly97613 жыл бұрын
Dont try this
@Alhussainba3 жыл бұрын
Well done, clean and elegant. Was surprised seeing a Lumia, I have my Lumia 950xl on my table bare back, the motherboard is probably dead as it sunk at some point, but I wanted to learn how the wiring works so that the phone requires the battery to work. Unfortunately, I couldn't replicate it with my Poco f1 as the battery doesn't have a + and - pins, it has an FPC connector and I don't know how to deal with it.
@abidurrahmanchowdhury44122 жыл бұрын
A bit late here. Have you tried detaching the BMS from your OEM battery so that you don't have to deal with the whole FPC connector mess? The battery pack along with it's protection board solders to OEM battery BMS which then connects to phone via FPC connectors.
@rimckd8253 жыл бұрын
Prob ok for MS phones - that's about all... None of my LG SPs look anything like this. Thnx anyway.
@umargul56443 жыл бұрын
Well done sir, thanks a lot
@mkcaplayz69783 жыл бұрын
You: Infinity% Me: 100
@inamulhoque26273 жыл бұрын
Nice idea. Thanks.
@urbantamizh53633 жыл бұрын
When I tried directly with usb cable to phones input battery terminal it starts up phone and after 3 seconds screen goes off...why it happens
@tgmtf59633 жыл бұрын
Too much power
@SiddharthHaobijam3 жыл бұрын
if it is samsung higher end phone it could be becos u have to take account the pin next to the phones input battery terminal . it seems to send signal to the phone that it is not connected. i tried directly connecting 3.something volt to the input battery terminal but it starts up n shuts down soon
@markjarvillemartin4228 Жыл бұрын
Take the BMS board. It probably has 3 to 5 wires connection to the main board of your phone. Use the original BMS board, and solder your external battery on it
@ajaynagar13263 жыл бұрын
on off ho raha h baar baar
@johnjacobs36733 жыл бұрын
I try this and it worked .i use a zte battery to power a samsung galaxy j3 and it turned on however when i try to chargwe it it saids the batery is not compatible how can i fix the charging problem. Do you think it has to do with the bsi and btem wires not connected??? Please help me
@marketersourav2 жыл бұрын
u have to charge your battery externally
@claudiofiero85233 жыл бұрын
Can you give us some more explanations about where does this battery pack comes from/ how you did it
@danthegreat75903 жыл бұрын
Well i know that if you have a battery of the same voltage it can be any kind of rechargable battery what i think hes doing here is wiring it directly to the positive and negative pins of the phone as long as its the right voltage it should theoretically work
@sweetpotato79932 жыл бұрын
@@danthegreat7590 But how would you charge this battery? I think he did not show that bit.