Hi Bert, We have purchased this property (and this exact fireplace that you fixed!) this year and need your help fixing the fireplace. Can you contact me please? Just let me know how to do this.

beatiful

Hello i have this burner in Ukraine, nice,thanks

We had this polish heater 30kw power at my job but it was weak so i drilled a hole from left side and put a pipe in there for extra fuel commimg in the are red hod when u pour diesel in there and it is better at startups because the hrating phase taking so long many times happened it run out of fuel before the heatimg phase was done ... pump don work in heating phase as u surelly know

3d printing the fan would be much easier

3 failures means crappy chinese shit== buy once,, cry once

*All practical tests of ground-based small wind turbines show the same thing: 1) They hardly produce any electricity. 2) They do not last long!* With solar panels, you can generate at least 10 times more green electricity with the same investment! Reliable and almost maintenance-free. Moreover, the wind close to ground is extremely gusty. 9 out of 10 small wind turbines therefore stop working after a short time!

Hi Bert WHAT low wattage external compressor will be good for the 50kw Bairan burner?

All practical tests show that small wind turbines hardly generate any electricity! And only at very high costs! Because there is hardly any wind close to the ground. It is also extremely gusty, which usually shortens the service life extremely! Only if you need to be off grid in winter & live close to the sea, you should install the largest possible wind turbine on a high mast. With solar modules, on the other hand, reliably generate electricity for 25 to 30 years at approx. 2% to 5% of the cost of small wind turbines! With 8 - 10 bifacial modules, you can generate approx. 3-4 kWh per day even in winter.

🌷🌷🌷

☕

What is the problem With just using the pressure pump as it is?

مرحبا سيد بيرت هل هاذا يعمل على زيت المحركات المستعمل ،

how much pressure do I have to set? Mine is currently working at 1.1 bar

Hey, would you like to sell it for the right amount of money?

Thank you for great job and installation finally home will be pleasant.👍

My 12kw growatt inverter mppt board is not working...Can i use one of these instead of buying the board ?

What is the model of this charge controller? Link?

Hi there. Thanks a lot for the great video. We just bought one here in Ireland the exact same. Its a bit chipped and the paint colouring isnt good. What kind of paint would you recommend. We were looking at a high temperature stove paint, would thay be ok on the enamel.? Almost identical colour. Thanks

If you have the manual, PLEASE. if you could scan it and put the pictures in a google doc make it public and put the link in a reply to this comment. i have one of these machines but no manual.

Hello there. You burn the right fuel in this beautiful heater but the wrong size. These salamander type heaters burn only stove size coal or 30/50mm as you can find it here in Europe. Good Luck. George

awful accent.

Great stuff 👍

I’ll give you this . Behind the black cover, there’s a adjustment for the giliotne air valve. Save fuel, and teach you lambda. I sold many, 200 pcs

Can you send me the contact number of the store so I can buy and ship outside of Australia?

You can make a good oil burner in siphon mode for this nozzle, but for me it is better to work with oil pumped system. Then you dont need a oil tank at all. Instead of tank you can use somekind of 200w inline oil preheater with valve for oil and for air. Also pumped oil which you send to the nozzle is regulated from 0 to 1 bar. You can use originally pump in one line and two line system. All you need is remove one screw from inside of a pump. Pump will be run with a 12v motor from car window system and it can be regulated with a PWM regulator or you can use stepper motor in combination with arduino. Filtration of oil is easy with a 50 microns filter. Better controller is the same model of LOA24 but with a mechanical relay instead of a cheap chinese elements inside. With arduino you can control and adjust every parameter of the burner...at the end....nice video...best wishes...and I would like to see your very well converted diesel burner in operation...good luck....

I have a working T216... no water pump... was used for generating power with an alternator... 3600 RPM out of the reduction gearbox. Biggest issue was finding the Turbine Mineral Oil to replace the 35+ year old in the gearbox. Found German manuals and translated them using web tools. Crank start. Electric start needs new toothed belt. Now to figure out what to do with it other than run it for fun and sound. Collaboration welcome.

These wind turbines are *JUNK* . It has been proven a thousand times already. WHY do you think yours would be any different?

Is it as good as the Bairan STW 120 multioil burner 10-50kw ??

What model is that? The SC48120-MPV? If so they have 'em still in the States..

bit close to the ground eh ?

Steam turbo blower without electric.

Hey what oil metering pump did u buy

Any watts made is good in my book .

So does the air go through the center of the nozzle

Is it normal that the burner always goes off briefly and then comes back on, or can it be set so that it runs all the time up to the temperature set in the thermostat

If you want to sell it at any stage, I’ll be happy to buy it off you :)

Does your charger have a fan running all the time?

👍

🤩

Nice ! :) Godd job ! :) Regards from Poland ! ;)

Hi . Nice MPPT ! :) I'm looking for a good MPPT for charging - wind turbine - 48V, 3000W I give a sub + like Regards - Paul P. EKO-TECH :)

You are correct. Tried two and they are both junk.

The panning back and forth is telling you that the machine is too low to the ground and is sitting in turbulence. This robs the turbine of power because the wind is being diverted to several different directions instead of being cohesive.

And when batteries are full heat comes out fan?

In my case, the burner spits oil out at the front when it's connected to the boiler :😢

This indicates that your front-end wind turbines does not actually generate electricity, so it does not have the ability to charge the battery. Normally, for this controller, a 12 volt battery will only charge when the input voltage of the current fan reaches ten volts or more. Please do not mislead other users here. If you have this controller, the relevant after-sales service can contact the relevant sales team to help you solve it.

Looking good Rob, thats a very cool setup.

That axle spinning is supposed to be connected to an oil pump. Like the old shellheads j-pump. For number 2 home heating oil. Im a Massachusetts licensed oil burner technican and i approve my above statement.

Because we the best 😊