Yo necesito conocer el 30 dé los gue usted me enseña en español
@juancarloscalderon53573 ай бұрын
Yo ocupo uno donde lo consigo ?????
@juancarloscalderon53573 ай бұрын
Con quien lo consigo ese equipo ????
@user-cx1df5qt1d4 ай бұрын
Harga berapa
@richbinaz4 ай бұрын
Very nice system you built there. Have you tried the Rabaconda duck head? It's a little smaller than the red one and seems to put less stress on the tires, both removing and installing. If you try it, make sure you get the standard one of the 2 available.
@marvincon14175 ай бұрын
That's one soft tyre,
@Elaba_10 ай бұрын
I can't find the video for car tires.
@dougiequick110 ай бұрын
Would be wonderful if I could actually BUY this stuff
@sstjacques11 ай бұрын
They don't sell this motorcycle attachment any more, at least at the HF near me.
@mybibleandmybike Жыл бұрын
Where did u get that yellow attachment? If u don’t mind me asking… I got a duckhead but the way I’m using it I can’t get the tire to go over the head..
@kbryanjones Жыл бұрын
KBJUnlimited.com I make them. :o)
@mybibleandmybike Жыл бұрын
@@kbryanjones I have the easyberg multifunctional do you have one for that? I would love to purchase one to make my tire changing a little easier
@kbryanjones Жыл бұрын
@@mybibleandmybike What size is the pivot shaft that goes through through the wheel bearings? You can email me at [email protected]
@joerodriguez1018 Жыл бұрын
Best modified I've seen great ideal
@adjbob56 Жыл бұрын
When you put the tire back on, the tire is supposed to go OVER the first part of the duckbill, then under the 2nd part. You have the tire under both protrusions of the duckbill, which makes the tire rub against the rim as you install the tire 7:45
@fmcra Жыл бұрын
Really helpefull how to use that without scratching the rims. Thank you sir
@mohdnooradnin Жыл бұрын
Seen many videos the red duckhead is very popular compare to the black and metal.
@johnperniciaro1126 Жыл бұрын
Thankyou, great video! Having said that, the tire looks as if it's been soaking in alcohol.... unrealistically soft?
@acke26 Жыл бұрын
you dont need a duck head. best way to not scratch or damage the rim edge is simply to turn the rim upside down with the face pointing downwards. Just cut a hole in a rubber mat and place it on the top surface of the harbor freight tire changer. When working on the backside it doesn't matter if you get some minor scratches
@bobknight33 Жыл бұрын
I just had local dealer changer my tires. $$$$$$ I supplied the tires. ( Pirelli Diablo Rosso ) $ 200 some bucks just to change them............ I asked they said 40$ each if I took tires off the bike and 90$ each if on the bike. -=== FYI this was the same quite I got from another store ........ Seems like with this changer -- buy and use 1 time and you break even and then some.
@andrewcannon587 Жыл бұрын
if only they improve the base unit to be more sturdy. The current harbor freight unit is very cheaply constructed.
@michaelosmon Жыл бұрын
Nobody sells the motorcycle wheel adapter anymore ugh. Maybe I can make it
@Knolgarcia69 Жыл бұрын
Hello, you have any idea where to get the motorcycle adapter with the three legs...I have the bottom part from Hrbor Freight but they dont seem to carry the motorcycle attachment anymore.
@emmettturner9452 Жыл бұрын
Would you consider selling just the center spindle adapter for 13mm?
When you install the tire you're supposed to use the other end of the duck head and go clockwise, it works a lot better. Nice kit, thanks for posting. I might order your kit it looks very well designed. 👌
@DavidM2002 Жыл бұрын
I've watched a number of the commercial vehicle tire changing videos using the duck head and you are correct about using the other side of the duck head but his direction is correct.
@Engineerboy100 Жыл бұрын
Did you make all those parts yourself or is there some place they can be ordered?
@jesusacovarrubias13902 жыл бұрын
Did you also buy the duck head attachment and bar from Harbor Freight
@a.c.e.75682 жыл бұрын
At 1:00, I don't see that setup at Harbor Freight.
@kbryanjones2 жыл бұрын
Yes it looks like they have discontinued it. But some stores still have stock.
@kbryanjones2 жыл бұрын
There is one in my local store...
@droneshaw56102 жыл бұрын
Very good video on using the Duckhead tool for motorcycle tires. I have a Honda GL1800 and mount, demount tires, I would like to try just the (FROM KBJUNLIMITED) *HUNTER RED NYLON DUCKHEAD 23.48 *DUCKHEAD PLATE AND SHAFT 29.95 * I also need a shaft, and am not sure how to attach one. Any advice would be greatly appreciated.
@justinwhite38512 жыл бұрын
What do you do with that wheel brace post on a wire spoke wheel? How do you lock it into place to change the tire?
@lloydhorton42902 жыл бұрын
Nice, but will it work with tubed tire?
@georgeroberts6132 жыл бұрын
Better I would think going back on to put the exact same position on the duckhead and go the opposite direction. No hang up on the bead and sharp angle for it?
@bastardoplano91492 жыл бұрын
I have motorcycles and cars. Would I buy both kits, the car kit and the moto kit? Thanx and great videos
@Al-of3zp2 жыл бұрын
That A/C mustn't be working too well for you mate.
@netorangel70352 жыл бұрын
Donde puedo conseguir las erramienta para una volcanisadora
@andybatchelor33212 жыл бұрын
Hi where did you buy the yellow kit at
@MrKromy672 жыл бұрын
Very helpful video, thanks.
@stevebrooks9712 жыл бұрын
great job but that's got to be a car rim.
@youuu43072 жыл бұрын
Great job man thanks 👍
@transportesslm18872 жыл бұрын
i need one,were can i buy one?
@kbryanjones2 жыл бұрын
Kbjunlimited.com
@ricky302v82 жыл бұрын
8:18 Over and under for putting the tyre back on, at this point the tyre is under both bits of the duck head.
@ruileal55742 жыл бұрын
You're right, he's using the duckhead wrong at the install
@justus11992 жыл бұрын
Outstanding rig, was able to change my tire with 80% less blood sweat and tears.
@johnmichaelkeryeskijr33612 жыл бұрын
Hi Keith. Thank you for making this kit. Also thank you for taking my call once I received it and tried it out. Fantastic unit. Well made the kit and video. As you said if it is hard you are doing something wrong. I was able to change tires in moments. Not even minutes! Tube tires take a bit longer just because putting in the tube takes a bit of time. (Super moto). My GSXR tires fell on the rims. Not a mark. Wow! To any one watching this just get it. Get the tire irons too. Wow are they a time saver. I will be buying more of those soon. This makes it so worth having. Mine is bolted to my garage floor when in use and removed and stored when not in use. So far I have done 5 sets of tires. My local shop charges $50-75 with tubes to remove and mount. Balance is extra. Do the math. If you work on more than one bike get this ASAP. Great tool, design and guy behind his product. Highly recommend, hell for that matter insist! John Keryeski
@MrVM412 жыл бұрын
Hi, where did you get the kit from? Thanks
@kbryanjones2 жыл бұрын
They are from KBJunlimited.com I make them. 👍🙂
@MrVM412 жыл бұрын
Hi, do you sell these parts, I'm in the U.K. Cheers
@maiconboani99482 жыл бұрын
onde compro essa ferramenta
@glennbuchanan57802 жыл бұрын
Sweet are you selling those I just bought a tire changer from Habor freight.
@kbryanjones2 жыл бұрын
Yes on KBJunlimited.com and also on ebay.
@ChopShopCustoms2 жыл бұрын
Thanks for the video. Definitely the direction I am planning to go with my changer mods. 😀 You mentioned showing a video with car tire changing. Are you still going to? I am interested 😁
@umeshlakhapati86882 жыл бұрын
indiyan Paris
@inpalpatine20672 жыл бұрын
Thanks. Nicely done
@DrumsByAdisa3 жыл бұрын
For what these kits cost you may as well buy a used No Mar unit, or new Cycle Hill unit.
@OU812NVME Жыл бұрын
????? Just made mine it's almost the same but better, made it like the regular tire changer excet 4 center holding stem :) welding is such a money saver
@toshkojelezarov90883 жыл бұрын
Great video! Would this setup work on tires with tubes or only tubeless?
@kbryanjones3 жыл бұрын
It works on tubes. There is less chance of pinching the tube with the lever as you only use it once to get the bead up onto the duck head.
@kbryanjones3 жыл бұрын
If you have a rim clamp either loosen it all the way or/and position it on the half of the rim opposite the half that the duck head travels around. (like you do with the valve.)