My experience is that their good for the money and very powerful while they run.

brilliant jobs

I've done this years ago with a couple of 2-stroke aero engines of .40-.60 size. I had to radically change the gear ratios to get any top-end speed out of it, and the engines ALWAYS ran hot with them being aero engines with a much smaller heat sink on the head. I had some success with using a tiny P.C. cooling fan blowing over the head, but proper sized 1/8 scale car car engines are always a better choice.

Wish mine would run as well as this!🤪

Pozz imam dva motora Enya29 iEnya 09 ..pa me zanima kako se to upali

How do u start it?

I have got one Vertex 18 for car. My question is: Is this a good engine?

Are all MDS engines crappy?

I was just curious why you would want to convert it to a four stroke if they run hotter and have to add a bunch of fans.Do they last longer? Do they have more power?

I use a micro torch to the cooling fans for a few seconds at a time and it loosens up the old castor oil so you can turn engine over. Use synthetic now so I never have that problem.

I have some MDS 61 with rear exhaust. The engine is very powerful ,but the bearings and the carburetor are shit. I replaced the bearings against good quality c3 bearings,and use a Webra Dynamix carburetor. It runs on a Speed plane like hell(over 21000rpm)with reso exhaust and 20percent castor/5percent nitromethan/75percent methanol.After flying i use automatic transmission fluid as after Run oil. So the engine never gummed Up. I make this with all my model engines,which runs with castor Oil, since 40 jears. My abc engines runs only for breaking in with castor oil. After 2 hours i change to full synthetik oil. Blend of castor and synthetik oil is crap. I use Motul Micro 2t oil. Greetings from Germany

Couldn't watch, because of music😩😩😩😩

This film was obviously attached only at the edges and then shrunk over the surface. Such covering film is easy to remove, no real need to shoot videos about it. The real challenge is removing film that was ironed to the surface over its entirety. That is a completely different story...

I have had trouble just setting up an MDS .48. Was never the engine but shit fuel, blocked lines etc. I was calling it worse than shite before trying fresh fuel and new fuel lines. Lol.

Hi ,I have the same engine but find it very difficult to set up right, when I tilt the nose up even slightly it cuts out! I would be really grateful if you can offer any advice. Cheers Danny

What prop size?

Is it eny good. I habe thought of buying two engines for a monster of a boat. But is this a brand i can use and trust or is eny other brands netter for the same price point

Stupid music dip shit

Can you suggest any modified engine mount you were referring? Thank you

Do u no the fuel and air setting for this carb

Very nice sounding engine. What brand of plane have you got there?

MDS (Moscow dog shit) we always called them. Total shit engines.

Thanks for the video! Was stuck with mine! Some questions...! 1. So do you screw in to the piston pin to pull it out? 2. Did you mark the valves to put them back the same way or does it not matter? 3. How did you clean the engine? Ultrasonic with Degreaser or carb cleaner? Or some recommend the antifreeze hotpot? Thanks!

Excellent film footage and sound.

I don’t know if you will respond or not, but will it seize back up when it cools down?

Prior to store a nitro engine i open the carb full with removed glow plug and pour in a 2stroke motorcycle oil and crank with starter until oil will come out on the glow plug hole

I about to clean mine been soaking it in vinigar had some rust on crank and 1 way bearing I only run it in 18 years ago in a thunder tiger mine is only gunged on crank all rust gone now will soaking it in methanol desolve castor oil

Paiaso.

How you extend the crankshaft?

Cook them in Propylene-Glycol or DOT-4 Brake-Liquid at 120°C for a couple of hours to begin with.

All you need to do is soak the complete engine in a bowl of petrol..

hello do you know the sleve messurements?

Hey, is the whole pipe straight or just the tip?

The carb is not good. My friend told me to remove the midle idle and put m3 screw that is sharp infront. If you do not want to waste time..send me the engine I will love to fly my planes with it :)

I just bought the cinebee! Unfortunately after flying it a while, I accidentally defaulted my fc with no backup. Would you happen to have a backup for it?

Tq!you save my day..2 of my rc engine now works well.thank you again.greetings from Malaysia!

below 3.5V there is no problem with r9mm ??

Looking to make my foam plane Slowpoke from Durafly much lighter.

Hallo Mark !!! the Phoneix 1600 it's a great plane to learn flight !! here my plane: kzbin.info/www/bejne/hX_Ue5iKpZatZpo

Looks like a nice build, I like the frame design👍😎 I guess once you tine the PIDs it will be a great flyer 👍😎 New supporter for your channel, hopefully you'll check out my quadcopter related channel and connect? 👍😎

good sound, nice job you still have this bike?

I used nail polish remover and 15% nitro fuel and it worked perfectly lol

Hey mark. Thanks for sharing this. So even with 2 antennas(diversity), if 1 antenna got damaged it'll reduce the signal strength yea? I just completed my build using r9 slim+, but im getting weird results, sometimes 99rssi, restart tx, it starts at 67rssi. restart tx again and back to 99rssi. its like random

Thanks you ! the heat gun worked out great!! Unstuck 3 engines

Haha thats a easy one! Try one thats been sat for 10 years or abused.. you wouldnt be able to lol

Where did you get your fuel from?

many thanks !

You would think a frame this size would be more stable. It’s shaking all over the place. Is it hard to tune or something?

👍👍👍🍻

Awesome.....