Kinda cute

Just replaced mine and now there’s a weird noise coming from glove department and 4x4 lights not showing

You can replace that dim light in the truck with a bright LED light. Same for the dome light

For the 2017 model year, Toyota updated the Corolla giving it a facelift and adding Toyota Safety Sense 1.0. The S became the SE and on the SE, those fog lights were replaced with Daytime Running Lights. The new safety features include a pre-collision system with emergency braking and pedestrian detection, lane departure alert/keeping, adaptive cruise, automatic high beams and sway warning

Great Video. The only thing different I would do is run the fuel pump once All the Fuel lines where hooked up to check for leaks before putting manifold back together. I think if it has Diagnostic box you can run pump from there or just turn key to ON Position NOT ALL THE WAY TO START, Just to on , fuel pump will Prime, Might have to do a few times to get fuel press up

OH my! The brings back memories! My mother's car and I drove it when I turned 16

Thank you

my coil pack went bad, changed . problem got a little better . misfiring, but least it started. changed injectors. ($700) . same shit. all this time the ignition cables where connected wrong

Something brought up my brother’s old Duster with a slant 6 and cherry bomb muffler. This sounds really similar to what I remember.

My trucks been having the cylinder 3 misfire. Changed the coil packs and sparkplugs, this is my last resort

My truck makes the same squealing maybe I need to tighten my belt lol

Good video. Excellent info

If you want to sell it lmk 🙏🏽

My Chevy has 249000

Did you have to reset the ECU after installing?

Just paint it

One thing you didnt do ..u should have ground out the center of the chip and any stray cracks to prevent spreading .. @ 2 you should have thinned the nail polish with acetone so it would penetrate better even with a mild temp vacum then pressured it into the crack seams..3 super glue works really well if you keep the glass ina cool enviroment allowing you time to vacum and pressurise the glue into the seams. end of fault fact finding mission

Do I have hook a scan tool and program it?

Put a small magnet inside your socket

Try friction weld with a Dremel and tpu filament piece 👍

just replaced mine on my 99 taco. thanks for posting i appreciate the tips and was able to replace it in under an hour including cleaning some parts

Nice! You should have gotten the full size one so that you'd have room for batteries and chargers and extra lenses (plus another camera as your company grows.

Any info on mpg?

Great video. Your explanation and step by step was helpful. Thank you.

This is a good procedure. Some added suggestions is to check the level of the fluid before you begin and keep an accurate track of the volume drained. I have done this on other vehicles; When I do this procedure I usually change the filter/strainer and clean the pan and magnets. When I am doing the refill I add an extra liter or quart and drain 2 liters at a time, try to cycle through the gears. No problem doing this as a one man job.

If you have a power steering leak would you recommend replacing both the pressure line and the return line? Your videos are great!

maybe you should look into how to prime an oil filter!

just what i was lookin for, thanks buddy 👍

I have a 76 mopar. Can you actually loosen the bolt to where it falls out???

I bought the StrongArm 4286 struts for a 1998 4Runner and they failed within 7-8 months.

The question I asked myself is how much/times the government take taxes for every it takes me to drive. I pay takes on license,registration, insurance, purchase the car,gasoline, repairs parts, inspection, car washes, and if they could tax the air going into the engine they would

i will die on this hill the 4th gen is the best overall

Just found your channel on my homepage. Thanks for keeping it simple and short, subbed

The flat bracket goes to the check valve to hold it in place

Yea I've jusr about had it with all these happy couples everywhere How about y'all piss off and get a room together, but stop rubbing it into my face by posting literally everywhere

Good job

Try crazy glue. Next time it works.

Fun fact, the Toyota spin on filter comes with some lube on the seal so you don’t need to oil the seal, but still good practice to do so

This 20 + Years Toyota Master Technician Approves.... Good Job!!! 👍

❤❤

Thank you from Australia. Your video helped me enormously with removing the injectors in my 2001 Prado. The original mechanic was talking $1000 AUD to just remove them before sending them off to be rejuvenated.

I just bought a 2008 SR5 that exact color and I love it!

Dude, you didn't even show the hard part: Removing the OLD rotors. The rest of this shit a teenager can do. Show how you removed the rotors.

They all had exhaust manifold leaks.

Editing is your friend.

Really cool video !!

Thank you very much for the video! Very helpful - information is good and clear and camera work is done well. One thing that would be awesome would be to provide the part numbers, quantity and torque specs. Small detail but makes videos that much more helpful and really adds value. Another helpful thing I find in videos like these is showing the struggle of getting a part out or a nut/bolt loosened. Helps to see what ultimately worked for you and highlight at least one option for a potential challenge. Mistakes or confusion is very relatable to don't feel like it needs to be excluded.

love your effort in making these videos. Would love to see a video on replace the trims & tape on the Limited 3rd gen 4runners!

That sounds like a lower tone version of my 3.9 v6 in my 92 d150

Hello, the loud man is for voice command