Hello, I am glad to receive your question. The standby current of our controller module is 6ma. The power consumption needs to be calculated based on the voltage you provide. I hope this standby power consumption can meet your requirements. Look forward to follow-up feedback.

@@qiachip thank you very much!

kzbin.info/www/bejne/aXK6dndjiJt7r80 How to connect 12V 1 CH remote control switch module to 12V load, door lock switch, non-12V load This is an animated video about module wiring, you can take a look I hope it can solve your problem, and look forward to follow-up feedback!

@@qiachip Lo comprobaré. Muchas gracias.

How to use: WIFI ceiling fan remote control kit to pair Smart Life APP kzbin.info/www/bejne/forSYnWXaNdgd6s You can watch this video for now. In a few days, we will release a related video with detailed instructions! Looking forward to your viewing

I'm glad you asked this question. Let me understand what you mean. You have two switches and one remote control. Then the remote control is used to control the two switches, and they use different modes, right? In theory, it is possible, but it is not recommended. Unless your switches are far away, because you have to consider that when you turn on one of the switches, the signal of the remote control may also be received by the other switch. So it's better to use two remote controls to avoid interference. I hope you can solve your doubts and look forward to follow-up feedback!

Hello, thank you for your trust and questions. Let us know that there are many requirements for lifts. We have produced a series of motor wiring and operation videos for this. We believe that you can solve your problem after watching this video. How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2202 kzbin.info/www/bejne/e4LcfJqah9-Nhac If you still have any questions, you can take a photo of your control box and wires and send it to our email. We will answer your specific questions. I hope to solve your problem and look forward to follow-up feedback.

good morning, if you send me an email I will send you the photos, thank you very much for your interest.

good morning, can you send me an email so I can send you the photos, thanks for your availabilit

Looking forward to your photos and solving your problems

I'm glad you're interested in this product. This is our new product. We'll put it on the shelves in the next few days. We'll send you a link after it's on the shelves. Thank you for your support.

@@qiachip Thanks for quick response. Looking forward. I hope it can work with Telldus Tellstick that also uses 433 MHz. Do you know if it does that?

@@qiachip Still no link?

I am glad to receive your question. If you purchased our product, you can program each of the two remote controls separately. They will not be related to each other directly. Because different manufacturers have different programming procedures. If it is another manufacturer, you have to follow his method. I hope I can solve your problem.

I am glad to receive your question. If you are not using it, you can directly cut off the power supply, so that it will not consume power. But if you are in standby mode, it will inevitably have a standby current. If your battery is fully charged, it can be in standby mode for a long time. So you can ensure its use by changing the battery frequently.

Excellent response, thank you. 👏👏👏🙂

Yes, it can. Many people use this module and use a wire as an antenna. However, I recommend you use the spiral antenna shown in the video. It works better and the signal reception is more stable.

I am glad to receive your question. This video shows that the communication method between the remote control and the lamp holder is 433MHz radio frequency signal. You can watch this video. kzbin.info/www/bejne/moDTYYush7uni5Y We introduce different lamp holders. It is convenient for you to choose. I hope it can solve your doubts.

Hello, for your question, we have a related video, How to connect 12V 1 CH remote control switch module to 12V load, door lock switch, non-12V load kzbin.info/www/bejne/aXK6dndjiJt7r80, which introduces the wiring in detail, and we hope to solve your doubts and look forward to your follow-up feedback.

Hello, I am glad to receive your question. It depends on the brand, because the programs of each brand are different, which leads to some compatibility and some incompatibility. You need to test it in practice to know. You can watch this video of ours. kzbin.info/www/bejne/aaqsh6iKbLprhKc How to use QIACHIP Multifunctional RF Remote Control Signal Decoder RX480E TX118SA RX480E Tester The decoder inside can detect models of multiple brands, but the limited frequency is 433MHz and 315MHz. I hope it can solve your problem.

Hello, buddy. I see from your homepage that you are a car enthusiast. If it is used for the central control of the car, I recommend you to watch this new video we made. kzbin.info/www/bejne/pWi2k4d4dsp0orc How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2402 It is mainly to see whether the voltage is suitable for your battery. If the voltage is suitable, then it is a wiring problem. I hope it can help you.

@@qiachip please tell me this remote work centre lock frequency 315 mhz

@@Siddhuvlogs__85 Our module is 433MHz. If you want 315MHz, you can contact us by email at [email protected] . We will develop and customize it for you according to the actual situation. We hope to solve your problem and look forward to your follow-up feedback.

Hello, I don't know what an ecooter is. But I checked it out. The answer given online is an electric scooter. If it is, then I recommend you to watch this newly made video. kzbin.info/www/bejne/pWi2k4d4dsp0orc How to use 2CH RF remote switch linear actuator controller forward reverse rotation momentary KR2402 You need to distinguish whether the voltage provided by the device you are using is consistent with the voltage of our receiver. I hope it can help you and look forward to your follow-up feedback.

@@qiachip Im sorry I meant an escooter. What's the power consumption of the remote as escooters battery is very limited

Yes, it will save the settings. Even if the power is disconnected.

Hello, although our video is not related to wi-fi, you still need to leave a message if you believe in our expertise. We just happen to have a video related to your question to help you solve your doubts. The video explains what to do with the fan light controller when your wi-fi is broken, which is to replace the wi-fi. The video link is as follows. kzbin.info/www/bejne/a3-wZmZon9d8eJY How to use wifi ceiling fan lamp remote control when changing wifi via Tuya smart life APP I hope it can solve your problem. If you still don’t understand, you can leave a message again. We will reply you as soon as possible.

You can interpret this in many ways. What I want to say is that this is a good device. A good tool that can help you make big changes.

In the past, people fought with their equipment manually. Now, people fight with remote control, such as drones and remote control devices. The purpose is definitely to make it more convenient for people and reduce unnecessary consumption. Do you agree?

Thank you for asking a question that many people want to ask! Answer: No need to re-pair or reconnect! If your receiver loses power, it will still remember the remote control. After it is powered on again, you can still use the remote control to control it; Only when you perform code clearing settings, the remote control needs to be re-paired Hope this can solve your doubts Best wishes

qiachip.com/collections/qiachip-remote-control/products/qiachip-10-20-pcs-kt05-433mhz-2-button-metal-remote-control-learning-code-ev1527-wireless-transmitter This link is our remote control package, you can buy a very cheap remote control price We also have other types of cheap remote controls If you need You can contact our email qiachip.com I hope it can help you solve the problem

Yes, it's really good. There is nothing wrong with your idea. qiachip.com/collections/qiachip-remote-control/products/qiachip-10-20-pcs-kt05-433mhz-2-button-metal-remote-control-learning-code-ev1527-wireless-transmitter This link is our remote control package, you can buy a very cheap remote control price. We also have other types of cheap remote controls. If you need it, please contact our email address qiachip.com. I hope it can help you solve the problem.

Sorry, we took out this switch for demonstration purposes. In fact, you have always had this switch! The device in the video demonstration is a fan light controller. So you installed it on the fan light. So did you originally have a switch to control the fan light? The switch in our video is this switch. If you still have doubts, you can compare your original circuit with the circuit after the connection. See what changes have occurred in the wiring process. Or ask an electrician for help. You will understand it much easier. Hope it can help you. Look forward to your follow-up feedback.

Does your original ceiling fan have a controller between the motor and the wall switch? If not, it may not be suitable for installing this remote control set.

Sorry, we took out this switch for demonstration purposes. In fact, you have always had this switch! The device in the video demonstration is a fan light controller. So you installed it on the fan light. So did you originally have a switch to control the fan light? The switch in our video is this switch. If you still have doubts, you can compare your original circuit with the circuit after the connection. See what changes have occurred in the wiring process. Or ask an electrician for help. You will understand it much easier. Hope it can help you. Look forward to your follow-up feedback.

You can take a look at our remote control, which has two buttons and is the same as the one in the video, and enjoy a richer operating experience; qiachip.com/collections/qiachip-remote-control/products/qiachip-10-20-pcs-kt05-433mhz-2-button-metal-remote-control-learning-code-ev1527-wireless-transmitter If you only have one remote control, you can also learn Momentary (Jog/Non-Latched) and Toggle (Self -lock/Self-Latched) to control the switch

I am glad to receive your question. What product do you have? What brand, zigbee or WIFI? Do you have a gateway besides the smart switch? Looking forward to receiving your feedback!