@reg26 I'm not home at the moment, when I do I'll look up the two versions. The only way to tell the difference between the mounts is by the looks. Sadly, they didn't label them v1 or v2.

@@R-TechEnthusiast Thanks so much!

@reg26 Ok, looks like they did away with v2 of the vibration dampener and only offer v1 and the newest v3. v3 is their new "universal" vibration dampener and it's supposed to be compatible with all their various mounts, so that's the one you want now. I may have to buy it myself and see what's different from the one I bought. Since this v3 is newer than what I had posted, the install my vary slightly, so be aware of that.

@reg26 I'm not sure which mount you're going to put the dampener on, but this is what Rokform says about the v3 compatibility: COMPATIBILITY: Version 3 works with all Rokform twist lock cases and motorcycle mounts (V2 for Ball Adapter Mount)

@@R-TechEnthusiast I'm going to give them a call Monday and see what they say. Thanks so much. I don't know why they just don't make one ready to go except the fact that you have to buy two to get it done lol.

Nice. I wasn't so lucky. I did keep it and try using it, but after having it a couple months, it started to randomly disconnect and would no longer connect to the phone, and I would have to go through the whole re-sync process all over again in order to get it to work. Got rid of it after I got tired of dealing with it.

You're welcome! Glad it was helpful.

I could be wrong, but I can't help but to think you might be mis-understanding the use of a vibration dampener. The point of the vibration dampener is to stop the high frequency buzz, generated by the motorcycle, from reaching your phone. Those high frequency buzz/micro-vibrations are what cause havoc to the internals of your phone and potentially damaging it. The vibration dampener reduces/eliminates those high frequency buzz/micro-vibration from reaching your delicate phone. It does NOT eliminate regular, bouncy vibrations. A vibration dampener is not a gimbal or stabilizer. Once you understand the concept of what a vibration dampener is and/or is not, then you can you appreciate what it really does for your devices. I use the vibration dampener on my bike for my phone and it works great. I also have another vibration dampener for my insta360 mount on my motorcycle. I would never install a phone mount or cam mount on my motorcycle without a vibration dampener. Those devices cost way too much to risk damage to it from the high frequency buzz/micro-vibrations caused from riding a motorcycle. At the end of the day, it's up to each person to put a value on their devices and decide if it's worth using a vibration dampener to protect their devices or not.

Sorry, can't help you with that. I no longer have that monitor.

You're welcome 🙂

No, it's only designed for connecting to a PC using USB and using Bluetooth to connect to smartphones and tablets. Unlike the GP9, which has various input ports, this only has the one USB port. If anyone has figured out a way to get the GP3 to connect to a console, I haven't heard about it.

I got it from Amazon, but they appear to be out of stock and it isn't showing up when you search for it. Amazon tends to hide products when it's not available for sale. It actually does come in quite handy. It's only 4v, so it's not powerful at all. As long as the holes you're trying to screw into is pre-drilled, then it's fine. Here's a link to the one I currently have, but is out of stock: amzn.to/4esYhNt. Maybe it'll come in stock again soon. Here's a link to one that is similar to mine, but with more torque and a case plus bits: amzn.to/3TvlAhy. This one is currently on a lightning deal with a coupon as well.

Sorry, I don't have the monitor anymore.

it's just a sticker of their logo. You can stick it anywhere you want.

Thanks :)

You're welcome :)

Thanks. The app has its purpose, as little as it may be. :)

It's a good buy, especially if you find it on sale.

I don't have that issue. Does it appear in the local recordings too?

No. I didn't try the local recording yet.

@@leonfx2009 try a different USB cable as well. Some people complained about the cable being the bad.

USB cable? There's no USB involved! I connect the receiver with the camera using the 3.5mm jack?

@leonfx2009 ah sorry, I assumed it was connected to a phone :) try a different 3.5 cable.

Good luck, that's what mine did as well. A series of clicks until I turned the key off. In my case, replacing the starter fixed the issue. I did end up replacing the starter solenoid as well since I already had the cover off anyways and just chalked it up to preventative maintenance :)

You don't connect stock parts to the Denali Cansmart, it's for connecting accessories to it. The video does show how to connect the auxiliary B6 brake light to the cansmart though. It's a simple plug and play connection.

It doesn't matter if it's a cheap or expensive multimeter. The panel might look different, but the process is the same. Set the switch to Voltage, make sure it's set to read DC power and not AC power, then put the leads on it.

@@R-TechEnthusiast Thanks!

I had recorded it, but I had originally misplaced the video. I did find it not long ago, but since it's so old now I never bothered to edit or post it. I do still use the Aoocci and have liked it since I got it.

With a LOT of patience. It's a pain threading that strap through the hole. It can be done though. Probably easier if you have fish line. Cut a short line and tie one end to the strap (not to tight) that is meant to go through the strap holder and feed the other end of the fish line through the hole. Once you feed it through, untie the line and secure the strap to the radio.

Should only blink blue and not blue/green after powering the speakers on by holding the power button for 3 seconds. Try doing a factory reset or a hard reset, then power it on and see if the lights blink.

Fuse? There's no fuse in the extruder that I'm aware of.

Try updating your firmware in the AAwireless.

I didn't notice any setting like that. However, my vehicle also has the usb port always being powered and I've noticed that the unit is actually off when I get into my truck. So I'm guessing it does shut off after a while of being disconnected and comes back on when the vehicle powers back up again.

Personally, I like it. It's many times better than the OEM seat, though I think all the major seat manufacturers will be better than OEM. I've ridden as long as 8 hours (with the exception of 1 stop for fill-up) and i was still doing fine. If you have the opportunity to try it out, or any of the other manufacturers, on another bike first, I would do that. Each manufacturer cuts their seats differently so what fits me great, may not be so good for others. With that said, I wouldn't go back to OEM. The biggest reason I went with Sargent was that I didn't have to send them my old seat and they had options with the heated panels built into the seat. The reason I didn't want to send my old seat was mainly because I didn't want to be without my bike while I waited for them to retrofit the OEM seat with the new cushions. At the time of my purchase, I believe Sargent was the only one that didn't require the OEM seat to be sent to them.

It's not required, it's recommended. Otherwise, once the battery is dead, you have to remove it and recharge the battery. During that time, the lock will have no battery power and will be unusable, with the exception of using the key. It takes many hours to fully charge these batteries.

No. The battery has a usb c port for charging. So any phone charger with usb c cable will charge your battery.

Same day. As soon as the fridge was set up, they immediately loaded the old one and took it with them.

some of the screws have locktite on it, which gives it some resistance when trying to remove it for the first time. As long as it's not rusted or frozen in place, it should come out with a little effort.

Thanks! Unfortunately I don't remember the name brand of the crash bars anymore. I had bought them directly from my local BMW dealership though. I had recorded the install of the crash bars, but sadly my camera battery died and I didn't notice until I had already completed and put everything back together again. :( Going by the pictures on the websites, my crash bars do not appear to be any of the following brands: R&G, Wonderlich, TouraTech, or Iliumworks. If that helps any.

As long as the connections on the back of the monitor match up to what your mac can connect to, then it should work fine with it. Monitors are not usually platform specific unless you're dealing with a niche product.

No, I don't have any white noise in my recordings, either on the video or local recordings...

Another person mentioned he was getting static, and after he swapped out the usb cable for a different one, the static went away. You might want to try a different cable and see if that helps.

Thank you for replying

It comes with a usb c to usb c cable for android and usb c to lightening cable for ios phones.

Glad it helped

I actually haven't had the need to use the local recording so I never compared the two. I did test and check and yes, my local recording does seem to be lower in volume compared to what's saved with the video.

@@R-TechEnthusiast Thanks for checking! Another point that could be good to know for users of people considering a buy; I'm happy with the mic and think the sound quality is ok (maybe not always great but good enough) but the included cables are of quite bad quality, stiff, and feel cheap. I had severe issues with static when filming with my Iphone and was very close to returning them but fortunately tested to swap the included cable between the receiver and Iphone since I had one of those cables and the issue went away completely. I could even feel a difference in connecting the cable to the receiver, the fit from the included one felt loose while the other one I hand felt snug och tight.

They are actually pretty convenient if you find one that works. After I got rid of this one and switched to another company, I've enjoyed using it, and now I like having it.

Cd quality - 48KHz, 16 bit stereo

I usually let new devices charge overnight.

This video I didn't edit the audio. I have had to edit it before, though. I noticed the mic is more sensitive than my previous mics, so I'm becoming more aware of where I place the mic depending on my surroundings. Mic placement has helped with reducing the need for audio editing or the amount of editing. If I need to edit the audio, I usually use the audio editor that comes with DaVinci Resolve. A few times, I have also used Audacity for audio editing.

Not much you can do other than making sure the power source is good. You pretty much have to contact tech support.

I sure hope the new mic sounds better. Hehe. I definitely like it better than the old mic I had.

Nope, on this model, you can't. I have no clue about the latest models, though, probably not, though.