@bugoutbrad8395 thanks for your comment and support

It's not a problem if you don't use the air vents

@AW-Services unfortunately not correct. I have to open driver and passenger side vents, even if not switched on, because the middle vent, where the phone holder is located is apparently where warm air comes in and there's so much radiating heat that we need to cover it with a fleece towel so it protects the phone from overheating Just another badly design issue of the 2018-2020 Renault traffic

I only used 20x3mm stainless steel cup head screws and a thin bead of silicone

Yes it's extremely reliable and robust

@AW-Services You would usually hear these sonic sirens on ambulance and paramedic vehicles, the police stopped using these quite a bit of time ago, you now usually hear police using whelen and Woodway sirens

@AW-Services Yes, I agree that they are very compact, reliable and robust without the need for any other wiring shenanigans for just the siren aha

@XFP5777 yes most ambulances have them due to them being small enough to conceal along with the STC controller. Most of the current police vehicles, such as ARVs and response cars, are using Whelen

Did you watch the video? The wiring diagram is visible within the video at 12:53

@ yes just worried about the eagle eye led’s do I just and them to the loop

What do you mean eagle eye leds?

Want to add lights to front for a fishing power box to light up my tent they call them eagle eyes led’s

You mean tiny 10mm white through hole leds? Do you understand how a circuit works? Battery positive - fuse - single pole rocker or toggle switch - positive leg of leg. Then connect all the negatives together, then connect to the negative of the battery.

In short, a video projector will only project the actual quality of the media it's displaying. Have you experienced any related issues with various videos or films? If using KZbin, there are occasions when media defaults to 360p if not changed on the lower right hand KZbin toolbar and gear icon to select your desired quality between 144p upto 1080i etc

I do believe they are coded. However, I've never removed mine, but I do have all the owners' manual and associated paperwork in the glove box from new

You're most welcome

Possible switch fault as its a momentary switch with latching circuit

@AW-Services I'm going to take rear bumper of today and see if anything wrong. My friend put a ODB reader on my van and the red light on switch has gone out, if I cannot see something obvious behind bumper think I will renew switch then take it from there, thanks for your reply 👍

Changed switch no luck ​@@AW-Services

@RobinTaylor-v1w they do work and also absorb a lot of ambient moisture

Many thanks for watching my video. The French make some great kit, and there is an abundance of genuine new surplus for sale. I'll watch your video and see your take on it. Regards from Austin in the UK 🇬🇧

Unfortunately I haven't the time to sell. Making your own mounts is extremely easy. Also, have a look at Etsy. Lots of creative people are making items for various interests. My mount is a short 45mm length of B&Q aluminium angle profile with a cut and filed slot for the Scanner belt clip. I've used some self-adhesive foam sheets to prevent the scanner from getting scratched and a generic cheap action camera / gopro style handlebar mount Motorcycle Bike Holder for Walkie Talkie Bracket, Adjustable Mount for Two Way Radio with Wide Compatibility for Anytone for Icom for Handheld CB Radios amzn.eu/d/gvkvBIj HYS Radio Extended Mount, Adjustable Walkie Talkie Holder Compatible for Motorola Tlkr Baofeng UV5R Kenwood Midland Two Way Radio, Suit for Bicycle/Motorbike/Car/Truck amzn.eu/d/7NFSWAe HYS Bicycle/Motorbike/Car/Truck Radio Mount Base, Walkie Talkie Holder Compatible with Baofeng UV5R Kenwood Midland Quansheng Motorola Tlkr 2 Way Radio amzn.eu/d/09xap4l

@@AW-Services ok thanks

FiNeWaY@ NEW SET OF 2 x 1kg LARGE DRY CAR VAN HOME REUSABLE DEHUMIDIFIER BAG MOISTURE DAMP ABSORBER PAD WITH ANTI SLIP PADS amzn.eu/d/5aRRDsO

The whole range goes down to 360p, but if using it for security applications, you'll get dreadful quality video

@@AW-Services Interesting. On the newer C225 I can only set it to 720P OR 2688 x 1520 and I can only record at 720P @25fps OR 2688 x 1520 @ 10fps. Will be returning this toy!

Yes, as I've not used them all summer, they were stored after drying them in zip lock bags until I put them back in my van last week. If you dry them fortnightly, they shouldn't stop working. Cheap white basic cat litter in socks also works as it's bentonite clay

They all appear to have failed. I had a few messages from people telling me they were junk

After countless emails and the latest telling me to try some developer based software, it still doesn't work. It is extremely difficult to gain a refund, and I'm being told to wait around until they find a fix. For transparency, here's my latest reply copied and pasted Hi Austin, It's no problem, we should have an update for this in a few weeks, your license remains frozen so you're not losing any time. Please note that this is specifically explained on the website, we have no way to guarantee perfect compatibility with future versions of firmware or OS updates, as is the case here. We are trying to add support for new versions as soon as it's possible, but it cannot be guaranteed. As a courtesy to you because your purchase was quite recent when this new update arrived and messed things up (please note this also broke the official DJI app at that time), I offered the freezing license option, which is not normally available for such situations, but that's the best I can do at this time. You will be notified by email as soon as the update is available. If you need help with the ADB procedure in the meanwhile, I'd be happy to assist you.

@@AW-Services I hope they can find a solution to our problems soon.

I'm trying to resolve it for everyone but it's far from easy

Update, it appears to be fixed with the new Beta version 1.13.10 (1060) kzbin.infoUgkxrsMFQVnGYTUlUc4FbhQYrbbTR6_4Ub6h?si=kTJWYSVlsUeaRoPd

Unfortunately its not fixed with this beta version (1060). App doesn't start ​on android 14 @@AW-Services

I'm pretty impressed with mine. Affordable yet reliable and does the job minus the price point of a Lume Cube

At this current time of typing your reply, I've still not resolved the issue. Drone Tweaks are dragging their heals and don't want to refund myself, and I've still not got it working. Below is the exact and last email I received from them: Hi, This is caused by a recent Android update, which doesn't allow apps built with older SDKs to run. The same problem happens with the DJI official app 1.13.10. DJI released an update (1.14.x) to address this, we are working on bringing FCC to this version but it will take some time, as DJI made some fairly drastic changes in updating the app to these new SDKs. The good news is that, if this is indeed the problem affecting your device, it is relatively easily fixable by following the ADB procedure described in the 5th bullet point here: www.drone-tweaks.com/troubleshooting

I didn't bother posting the MKii version. It only featured a black abs enclosure and spring Europe Ltd V11 pump controller flush mounted on the top surface. It only required waterproof power switch

and i'm a youngster

I'm fully aware of that, thanks. Just sharing an affordable, ready built option for those who may be making models, etc

@elitefleet6402 if you have a controller such as a spring Europe Ltd V11 or V16 it won't work because the controllers need to be physically switched on. Or if using a cheap Chineseium controller which is technically a motor speed controller it also is switched and sometimes has a start button. The common sense approach would be to have the remote control wired in after the pump controller, and then you'll only be switching the pump on

@@AW-Services Thanks so the only other way is bypass the controller switch and fit an actual on/off on the controller box. just thought oh i have a remote laying about from another project that never happened.

You can use a remote control, but don't fit it before the pump controller, as you'll be switching it on and off. You only need to actuate the pump as that's the only moving component that does any work

It couldn't be an isolated issue

Single rear roof bar low profile beacon, windscreen suction mount beacon will do. Don't buy anything on Ebay or amazon. Use beacons & lightbars or lightbar UK. Only get Reg65 chapter 8 equipment. The brightest spec available

Try using BF-1904 or BF1907, which are listed as they are the same type of radios

@kierancali check out my DIY ammo powerbank playlist. All the information is in the first build video description or look at the comment below this one ⬇️

@@chrisbutler1831 a dedicated lead acid AGM battery charger

@@AW-Services I couldn’t find the list but I’ve found it all now. Cheers. Even tho the battery says it needs to be vented when charging you say it doesn’t am I understanding right