7 сағат бұрын
12 сағат бұрын
2 ай бұрын
2 ай бұрын
3 ай бұрын
3 ай бұрын
Пікірлер
@BrendaWyatt-jw9qx 9 күн бұрын
Pretty dumb that it doesn't show how to take the plate cover off.
@hexx-im1tf 11 күн бұрын
This seems helpful. Not sure if I want to attempt it. Those close quarters get me nervous. It was bad enough changing the spark plugs.
@DZGunner 14 күн бұрын
goddamn, longest fucking bolt ever @3:50
@Andeev3 16 күн бұрын
Keep doing what you're doing!
@rj6013 21 күн бұрын
What’s your contact if I want to get tuned?
@tschmidy183 21 күн бұрын
Email is [email protected] without the dashes
@Godsman_42 21 күн бұрын
Hey what spec did you tighten the valve body bolts to before placing the cover back on?
@justinleuschen8258 23 күн бұрын
I’ve been trying to figure out the cylinder firing order. Tell me you know because I have found 3 different answers lol.
@justinleuschen8258 23 күн бұрын
Where is 1 2 3 and 4 located ?
@tschmidy183 23 күн бұрын
If your looking at the engine, All subarus are left lower cylnder 1, left farther from you cylinder 3, right close to you cylinder 2, right away from you cylinder 4
@DZGunner 28 күн бұрын
nasty
@Zomby061 29 күн бұрын
Im bricked😂
@rj6013 29 күн бұрын
Can you etune if I’m not local?
@tschmidy183 29 күн бұрын
Yes i etune alot
@rj6013 29 күн бұрын
@@tschmidy183 how do I contact you have an email?
@rj6013 27 күн бұрын
What’s your contact info
@rj6013 21 күн бұрын
@@tschmidy183 what is your contact info?
@rj6013 21 күн бұрын
@@tschmidy183 how do I contact?
@78LT.96SC Ай бұрын
Loved the quick demonstration. My SC2 started shifting hard, but I've had the parts ready for this replacement for a while. Plan to get it done tomorrow. Fingers crossed, I don't need anything more than replacing this and tightening the input shaft nut 🤞
@DZGunner Ай бұрын
i wanna see a hitler stache
@24revealer Ай бұрын
May I recommend better titles on your videos so when searching for subaru head gasket replacement they come up in the search?
@tschmidy183 Ай бұрын
Sure. Trying to get better at titles
@ohhshethicc5986 Ай бұрын
What bov you got? Sounds nasty!
@tschmidy183 Ай бұрын
Tial But the bov noise i think your refering to is actually intake sounds of turbo sucking in air and then some of it coming back to turbo
@boblum3360 Ай бұрын
I had a 1995 SC1. I loved the car but went through 2 of those parts.
@werwefsefsefsef Ай бұрын
love to see you working with your son, dream dad moments
@georgetaylor8654 Ай бұрын
One thing I learnt is that sometimes the fuel pressure can cause the injectors to get clogged. So be careful doing other that the cyber truck sounds mean when you advance the timing a couple clicks back. This advice is free 👍
@eggdude5460 Ай бұрын
What is happening, how do you even tune an electric car? Id imagine they get all the power you can get from the favtory
@tschmidy183 Ай бұрын
Its just a joke
@DZGunner Ай бұрын
ive been rebuilding CV's lately and they make me wanna kill myself
@azrcs7851 Ай бұрын
The cyber truck at the end 😂
@robmesaaz5737 Ай бұрын
Still looked like the gas gauge was on E!!!! Lol
@cindykuehn2743 Ай бұрын
More!
@Richard-lm8ho Ай бұрын
Is that peanut butter?
@Salvare008 Ай бұрын
So to confirm, if i wanted to be able to drive after upgrading to the 1050x, I just need to enter in '1050' to the flow scaling and then the latency numbers for it? Just wanted to be able to drive safely to a shops dyno instead of getting it trailered there.
@tschmidy183 Ай бұрын
Si
@Salvare008 Ай бұрын
Awesome! That just saved me a bunch by not having to pay for a trailer rental/tow.
@tschmidy183 Ай бұрын
@@Salvare008 most tuners probably dont want you to know that. Also latency numbers can vary a bit. But yeah just be careful flashing, Always make sure not to move much/make sure flash is seccessful. Not That hard to brick an ecu
@Deadslayer12 Ай бұрын
would love to see you build and keep the car! want some inspiration from you and this wagon!
@DZGunner Ай бұрын
e85
@cindykuehn2743 Ай бұрын
Sell it--crazy headlights!
@azrcs7851 Ай бұрын
KEEP
@maxmulder396 Ай бұрын
Sick car. Love to see more
@DPZ-gw4ne Ай бұрын
That’s bad ass man 🔥🔥
@DZGunner Ай бұрын
how much HP is he aiming for?
@tschmidy183 Ай бұрын
Not sure😂
@azrcs7851 Ай бұрын
good vid trell!!!
@cindykuehn2743 2 ай бұрын
Impressive!
@thomaspace1335 2 ай бұрын
Take a look at the tip-in enrichement table if you haven't already. Looks to be spiking lean when you go WOT.
@DZGunner 2 ай бұрын
more cleaning montages please, very satisfying
@benc911 2 ай бұрын
full throttle when the engine is cold, oh dear. You need a wideband 02 sensor to monitor afr as the factory one only reads cruise....
@tschmidy183 2 ай бұрын
😂😂😂 literally monitoring when i was crusiing kept it under 50 percent throttle on the colds engine. Just a little boost.😂😂 yall are funny. And yes i always tune with a wide bank i just dont show alot in vids, thanks for comment and watching tho!
@benc911 2 ай бұрын
@@tschmidy183 hey, it's your car. If you wanna boost it whilst it's cold then go for it. You also need knock control. Det cans we call them in the UK. The knock sensor control on the standard ECU doesn't see all knock.
@tschmidy183 2 ай бұрын
@@benc911 im quite certain nooone in the us uses them. In fact most tuners have never even heard of them. Ive been around dynos for years, never heard one even mentioned. But it doesnt hurt to look into them. I dont mind criticism at all as long as its helpful and not pointless. Lastly coolant temp was around 140 , i think thats ok for a couple psis of boosts lol. Would never stomp on it on cold engine ever.
@jeremyhubaker1199 2 ай бұрын
SURE WOULD BE NICE IF YOU SHOWED HOW YOU GOT THE GUARD OFF THATS THE PROBLEM CANT GET IT OFF TO GET TO THE DAMN BOLTS
@tschmidy183 Ай бұрын
12mm wrench, if your looking st the passenger side go from the back , break it loose, then its easy. Its just the breaking it loose thats hard
@zachbecklake2303 2 ай бұрын
1200cc injectors for a 90mm turbo. Someone likes running lean
@Zaid_Mohamed 2 ай бұрын
Mapping without det-cans... not exactly smart. Can't just trust the knock sensor or what the ecu logger telling you. It's poor practice. you need det-can to hear for det. This seem to be a common trend in USA. Then wonder why scooby get bad reputation for blown engines over there.
@cindykuehn2743 2 ай бұрын
Is that your bmw?
@tschmidy183 2 ай бұрын
Yes
@abbas674 2 ай бұрын
You do know boxer motors need to heat up all the way before it even hits boost
@abbas674 2 ай бұрын
Are getting a tune
@abbas674 2 ай бұрын
Are getting a tune
@DZGunner 3 ай бұрын
can i request some mozart in the next video?
@tschmidy183 3 ай бұрын
Will do
@Awdkaleb 3 ай бұрын
Good vid trell :)
@petesan3 3 ай бұрын
What fuel pump are you using?
@tschmidy183 3 ай бұрын
At this time it was stock. But it is now an aem340
@petesan3 3 ай бұрын
@@tschmidy183 any issues while with the stock fuel pump?
@tschmidy183 3 ай бұрын
@@petesan3 the stock one was toast so yeah was leaning out on top end. Swapped in and had all the fuel. It was a toast pump tho
@911CARRILLO 3 ай бұрын
Really enjoying your videos, super cool to watch the family getting involved too..cheers!
@danielclark5170 3 ай бұрын
Good video, I would have a valve job on both heads done if I was going to tear it down. Only makes sense if you're replacing the head gaskets.
@tschmidy183 3 ай бұрын
Wasnt my choice just told what to do, but i completely agree
@davidbye11 3 ай бұрын
Good work man.
@Awdkaleb 3 ай бұрын
good video!!