ive followed this on my TX and still nothing works with telemetry....i think my tx must be faulty. i have had nothing but faults with my t18mz...two batteries failing and telemetry never worked....i am now changing over to radiomaster.

Hi daniel. I'm considering buying this radio but a bit nervous about transferring all data from 14sg to 18sz. I understand how to copy over models with sd card but will all my telemtry funtions work the same without any problems? I have 7 models. 6 of them are on faast and 1 on faastest. I understand i will have to relink all 7 receviers to new transmitter but is that it all? Will all data transfer i.e mixes/trims/telemtry etc. Anything else i need to know?

Damn that guy can fly 😀

Thx for your help! I am using a 16iz to connect to an ikon fbl. Are there any external wires that I have to connect to the ikon to enable telemetry? Outside of the power and governor leads? I would like to ensure I am able to get MAH burned during each flight ..thx u again for this

Is this same for the newer T16IZ transmitter ?

a great instrument !!

Where you running the stockpipe in this Video or an other better one ?

Nice flying!!!

Hello Daniel Thank you for the video can you please do a video on all the different types of futaba receivers and explain the difference between them as I have not been flying for about 10 plus years and it's all a bit confusing ... eg they never had sbus or telemetry back then can all the receivers do telemetry and what is sbus .. please note I only have the old 35mhz receivers ppm & pcm at the moment and I want to start flying again but I want to change all my radio gear over to 2.4Ghz all the best from Ian in England... stay safe 😷

I was there

I've had this radio for 2 years now. Awesome stuff. Sensors work great, just be carful when setting slot numbers as one sensor may interfere with another. I have all their sensors. 💘👍💘

i just build my synergy 516 and i followed the manual direction that the belt tensioner needs to be 90 degrees to the frame. but when i spool the heli, the belt squeaks and after 3 minutes the belt gets very hot. the belt tensioner temp was 118 degrees and the belt began to shed (powder) on the outside. when i give the belt some slack, every thing is fine, but now the tensioner is no longer at 90 degrees. i need help

can i put a 550 blade on the synergy 516

Good evening. Excellent video, well explanatory. I bought a SBS-01G sensor, but when using it in my futaba 18sz only appears in Telemetry: Altitude and Variometer, is my sensor is defective or has some configuration that I may have forgotten.

Forgot to comment also great camera work too!

Speed and pitch. Thank you

Great presentation, but the music detracts big time!

Good flying Kyle, great precision! I want one!

Nice piloting

Congratulations on the launch. It looks to be a fantastic piece of engineering. Seriously am impressed enough that I'm gonna jump boat to look for where I can get one in Asia.

499 sounds nice to me 599 would be Fair look at the goblin 500 $602 and people are buying it

I'm 42 years old Stacy is a Beast of a helicopter pilot but I prefer Matts Flying Style I can actually see the helicopter LOL eyes not like they used to be can't wait till it comes out best part made in the good old USA

no need boom support?

Nice heli! Maybe I've been to too many concerts and my ears are showing signs of wear; I can barely hear the speaker over the background music.

connection to Futaba, is it thru S-bus or s-bus 2? Is the castle telemetry link adapter required for this to work? thanks for your time.

Is that radio had voice alerts like in spektrum like hold mode idle's, timer ? And is there a big dissonanse beetwen MZ?

Does this transmitter have a weak signal alarm? (rssi)

is it worth getting...I always bought traxxas t max 3.3

Hi, can you help me with the setup of the rescue fbl and TX thanks

How bad the drift during rescue? Have you tried BD3 SX, or Spirit FBL? what do you think overall? thanks! :) PS: Nice machine and nice flight !

great sound

Yeah, I think it's great. Good quality wheels and tires are a must, everything else is pretty much just if you want it. Install good high-torque servos, tighten up the servo saver, and getting a better radio will make it drive like a champ. Play with different weight differential oils to make it handle differently.

Heat cycle method. I add a tsp of Klotz Benol castor oil to a quart of my Werks nitro, and wrap the head with foil. Then with a very slightly rich setting run the engine up to 190 to 200°F for 3 minute intervals 5 times letting it cool between each run with piston at BDC. Then I drive it for 5 minute runs around 1/2 throttle with short full throttle bursts now and then letting it cool between each run at BDC. I push it a little bit more after each run until I have about 30 minutes run time on it

You might as well buy wheels and tires right off the bat, the stockers are pretty flimsy. Those and better servos are the biggest standout things for this kit. Aluminum washers for the wing from the MP9 are also worthwhile.

At the time I made this video I was using the stock clutch and gear ratio with lightened steel spur gear, 5k wt oil in front, 7k center, and 3k rear differentials. I have since installed a clocked Nova .28 with an Ofna 086 pipe, M2C clutch, 15T pinion, and added the extra spider gears in the differentials. It's a monster!

im geting one soon any tips and things that brake first or the weakest parts. thanks

HEY THERE ARE YOU USING ALL STOCK CLUTCH AND GEAR MASH ???

Which break in method did u use, having a hard time with mines

I am using: Light blue Hard springs on the rear and stock at front.

I used brand new team orion AA batteries. My wing took most of the damage and it's not straight anymore.

I no that feeling man, ruined a great engine because of dead AA batteries. Lost control and the car was in full throttle. no servo response so could not steer or apply brakes

This a good rtr truggy? What hop ups do u recmd outta the box? Im in love with this f*cker

Warnings before use: Don't drive whit AA or AAA batteries. buy battery cells to avoid crashing. Happened me once.

Stock shocks and oil, I just adjusted the springs on the rear and put orange springs on the front.

What kind of shocks you have?

What kind o f c

Oh man I love this truggy I'm so getting one and for the price that they are they are a bargain :)

thks

I would say nothing is bashproof... but its a good rtr. With a couple upgrades it's an awesome bashing rig.

Yeah, the factory ones are crap. AKA wheels and tires are awesome. I've been running one set of IBeam soft tires for about two gallons and they still have lots of tread on them. The wheels are very strong - I broke a suspension arm and bent four pivot shafts and I haven't had a single problem with the wheels cracking. I'm pretty hard on them and haven't had any come unglued either. They have a tight bead design.