Hey brother. Would your last name happen to be Wise. I went to school and had a best friend growing up that looks exactly like you. Darren Wise. He was an epic mechanic. Used to own an 88 firebird. White....

does the cylinder have any markings ? trying to tell if mine has a oem cylinded or aftermarket

Cheers for the advice about using the King Springs standard height instead of the raised springs. We're gonna replace the suspension but plan to install the 2" lift in the near future and wanted to ensure compatibility!

That tongue 👅 is in over time too hahahhaa

Finally........a 009 video with a sharp chain.

Nice, what electric ratchet it that?

Jack handle makes a good cheater

Junk..! I have pop up piston and cylinder from hwy.! 25 tanks through it, rings and piston failed miserably, do not buy, stick with oem.!

I'm guessing this is the first time he has done this job.

Man whats the point why not slo this down and tell us what your doing se your helping people learn this was just a waste of time.

Молодец у нас это называетая.

Great video. Where do I find the kit? Thx!

This saw is doing it brand new after the first use. Any suggestions?

The eBay Special Coil Isn't bad, That been said Mines been in saw for 2+ years But have Seized saw 3 Times First time I put a 58mm Big Bore Kit in It seized, second time I cleaned the alloy Transfer up with Muric Acid and a light Hone on Original Bore, i realized that that Tylon fuel Hose isn't temp proof Which has been my problem all along It melted and came off the 58mm BBK and Spilt on the other, I've procured Some heaver Rubber type Hose for that spot When I get My next Rebuild Kit a Metior Itailan made Kit as a Genuine Is out of my price Range.

Worthless video! Does not fix surging but does clean the carb bowl.

OMFG this guy has made this job look so much hard than what it is! A clamp?!

great info, thanks from the US

I'd like to know what happens when a bull ant climbs up the back of your leg. How thick is the back padding? It would be nice to have some armour all around shins and calf.

Haha, I’ve done that with the clutch as well. They really take off if you happen to be outside. I’ve remembered to torque them down since that happened.

Kid makes video. Doesn't really know what to say. Dragging it out to please Dr Algo' .

Works on the ms250 also 👍

Australian models generally follow the trends, and all my saws have the spark arrestor screen. I use a butane gas torch to clean them occasionally, I also don't rush into using the saw - I let them warm up for a few minutes on idle, that gets the fuel flowing through the fuel system and gets the oil lubricating the chain/bar. In theory if fuel is good, and the saw can breathe it should run. And keep it clean. 😎

it hard to understand when you fast forward

I know this is 5 years old, but why not just use an OEM crankcase gasket? I'm just about to order one from DIY spares out of the UK for around $3 AUD (along with a heap of other OEM bits for my 044 rebuild)

Make sure you grease your needle bearing before putting it back on.

please Give me One piece

How are they a few years later?

Thanks for the review and honesty. I'm waiting to see what the 'hurricane combo' performs like on my late fathers 1980's Husqvarna Rancher 50. For what they cost, I don't expect the same result that we get from the more expensive Husqvarna/Stihl gear - but then again, I'm not clearing large amounts of timber so if they work its good.

Yo quiero ver como se despega para sacar el seguñal

Great tutorial, wish I saw this 6 months ago. ❤

istopped at 152, this is madness lol

Great video. Short and to the point. I've never done this on a Subaru, so your video helped a ton! Thanks!

Can you explain anything you're doing in the video? I understand if you're struggling on some parts but maybe tell people if they should expect that. Cuz i got no clue what ur doin so i cant follow

Mesin kelas berat bro

Mesin kelas berat nih boss

395 sama 394 mirip ya bro. Cuma beda intake nya

Cylindet piston 372 bisa di pasang di 365 tidak ya bos

Kalau alat2 nya lengkap pekerjaan jadi lebih cepat dan rapi bro

Apa maksudnya husqvarna 365 pake boring 372 bro

Thank you from France, good video 👋🏻

Nice tip. Good video.

still going? hahah

I did this and when I took the muffler off there was no arrester screen. Gave it a good clean anyway but when I tried the start the chainsaw, I ran but as soon as it was idle it could out and I could t get it started again.

Use hot water to remove tubes you will damage them

dude great review I already have a 70 cc Perla Barb and love and I just got a 84 cc these are a good saw I love em

Preload need to be adjusted for kingpin and wheel bearing. Fellow, the service manual . This guy is allergic to torque wrench

Hay unas marcas las cuales dicen in y la otra out cual de las dos se coloca hacia el lado de donde viene la vencina , osea el estanque.

Great comparison. I just ordered a kit for my Forester XT 2014. I live in Sweden and it's tough to find quality stuff around here. Luckily, I'm visiting my brother in Adelaide for a couple of weeks so I ordered a kit to be shipped to him, and I'll bring it home in checked baggage👍

Thats does not look like fun

Driving sprocket