Hi...can u tell me what to do for d108 eroor ..n i can not reset it aswell
@c4circuit25 күн бұрын
Please Share drive model and make.
@AshikenIslamАй бұрын
Please send atv312hu15nu parameters
@RajwinderSingh-wh2tgАй бұрын
Pls send your contact no.... control card mai green light nhi chal rhi... Red chal rhi hai
@c4circuitАй бұрын
Drive k display par kya fault show ho rha hai
@RajwinderSingh-wh2tgАй бұрын
@@c4circuit A5001
@c4circuitАй бұрын
Replace control card.
@RajwinderSingh-wh2tgАй бұрын
@@c4circuit kha se milega... ya repair ho jaega
@c4circuitАй бұрын
Drive ka display change karke dekho agar phir bhi fault change nahi hotta to vfd ki details [email protected] par share karo.
@muhammadhamzanadeem4788Ай бұрын
Alarm 5001 Ka kya faulty hota ha sir
@c4circuitАй бұрын
Watch this video you will get your answer kzbin.info/www/bejne/mXisnZx6jJlkpdE
@mangaldev190Ай бұрын
Sir 9902 2 set kiye h or on off push button use kiye h start karna per 0011 fault aa raha h
@c4circuitАй бұрын
This fault is related to motor id run. You can do one of two things 1. Set motor parameters, connect motor with drive and apply start command to drive. Make sure motor is not connected to load or 2. You can disable this fault by setting 9904=3 9910=0
@mangaldev190Ай бұрын
@@c4circuit sir bahut bahut dhanyawad 🙏🙏♥️
@hmzanoor2 ай бұрын
370 voltage per fault a jaata hak
@hmzanoor2 ай бұрын
Sir A2005 fault under voltage a rha hi voltage adjust kesy hoga
@c4circuit2 ай бұрын
If your VFD is ABB AC355 or ACS550 1. Input supply kitni hai? 2. Parameter 107 mein DC voltage kitni show kar rha hai. 3. Agar fault on load vfd run karne par aa rha hai to soft start resistor ko bypass karne walli relay check karo. 4. DC bus bar k capacitor faulty ho sakte hai. 5. Igbt k converter section kankoi phase bhi open ho sakta hai.
@ansarisajid27402 ай бұрын
ABB ki 40 hp VFD 1310 ka alarm aaraha hai?
@c4circuit2 ай бұрын
Drive model?
@user-dz1nm6ed4y2 ай бұрын
Hello! You can clarify about the parameter P103. What current should I set if the rated current of the motor is 5 Amperes when connected by a triangle. Should I set 2 times less than the overload current by 150 percent and divided by 2, that is, 3.75 Amperes? Or are the overload parameters set in section A?
@user-dz1nm6ed4y2 ай бұрын
@@c4circuit Thanks for the reply. As I understood from the manual, the motor current min 0.00 max x2 is set in the P103. And if the current consumption if it exceeds the setpoint in P103 by 150%, then after 60 seconds, the error F 07 should occur and the drive will stop the engine or by 200%, then after 3 seconds. The current consumption of the engine is shown in D 103 3.2 A instead of 5A, as indicated on the engine when connected by a triangle. To be more precise, the 1.1kW 380 V motor consumes 2.9 A , and the 220V 5A triangle. I connected it to a triangle, since the frequency converter is from one phase to three 230 V. I set the setpoint 2.1 A in P 103 and the drive gave an error F07 a minute later and stopped the drive. It's a pity I didn't check the current with an external device. So it will turn out strangely if you set the setpoint to x2 of the nominal value of the engine. Have you checked the actual operation with the current set in the drive and the current consumption of the engine?
@c4circuit2 ай бұрын
Thank you we will check and get back to you soon.
@user-dz1nm6ed4yАй бұрын
I checked it out. In this parameter, you need to set the rated current of the motors. If it is 5 A, we set 5A. There is no need to apply any multiplicities to the motor current.
@gopi_932 ай бұрын
Thanks 👍
@c4circuit2 ай бұрын
Welcome
@MAVOORTECHMVR2 ай бұрын
Phone number
@sudipkandu26933 ай бұрын
🙏🙏🙏Thank you sir
@c4circuit3 ай бұрын
Most welcome
@samsamo7203 ай бұрын
Plz can you write what's dio you do here. Because we don't inderstand your language.
@c4circuit3 ай бұрын
In this video we were teaching our subscribers how they can run ATV12 vfd in Hand mode by pressing Mode key for 5 Seconds and how to disable OPL fault by setting flt > opl to No.
@SanaDawar-te5jp4 ай бұрын
❤
@c4circuit4 ай бұрын
Thanks
@hansrasirj99204 ай бұрын
3181ka bhi btao
@c4circuit4 ай бұрын
Check IGBT module and IGBT gate driving circuit.
@Saidun.ee14 ай бұрын
Please share your number
@ShahieryarBhatti5 ай бұрын
ASalaam alaikum ustad ji Maine kam sikhana hai please
@TechnicalMrKapil5 ай бұрын
Sir reset nahi ho raha he
@explorenature43635 ай бұрын
❤❤❤❤❤
@sunilpurohit43695 ай бұрын
Sir ji aap ke number kya h
@sunilpurohit43695 ай бұрын
Nice sirji
@dr.brcfanarmy64417 ай бұрын
ACS550 ka v circuit explain karenge please
@c4circuit7 ай бұрын
Which section?
@user-xb6rc2ku6u7 ай бұрын
کو عربی
@mosatamajrt62527 ай бұрын
سلام عليكم
@c4circuit7 ай бұрын
This is not a parameter issue, it is a hardware problem you have to replace the control card or 8 pin eprom with the new one.
@hitendrasinhjadeja5831 Жыл бұрын
Display kitne ka aata hai or kaha se milega
@c4circuit Жыл бұрын
Ye ACS355 ka hi display hai jo company drive k sath provide karti hai. Agar apko apko new display chahiye to please contact your local ABB channel partner.