Where do you get the vent?

Where did you get the vent?

Wrong! Go to Home Depot, get yourself a pack of 3inch multipurpose screw and use them as a replacement. And then go ahead and replace the rest. You’re welcome!

Good ole scrap piece of 2x4 and a piece cut 4 foot will do that do 😂😂

Thank you my friend, I was thinking about no nails, or glueing powder wood or sticking wood pieces but couldn't be bothered to get the wood etc etc and the little pointy fkrs were in the kitchen cabinet all along.

Chat gpt search for your video

Awesome video… after 2 pins broken LOL

Use glue first. It reenforces the toothpicks.

can you please share how we can reach you

can you please share how to reach you

Don't tell, show

Good job.amen

Where does one get a bow wrench

Did it last !?

Note to self: marry a handyman ❤

works great for composite decking also

It's bullshit that tool is ever needed

Buy a mitre jig for grinder so much easier and cleaner

I'm about to do this, but with plastic trim to match the existing trimmed baseboard (I'm finishing the niche for freestanding bathroom vanity where there was a built-in vanity before). I've cut the tile to match the floor grout lines up on to the baseboard like the previous work. I think it looks better.

Thank you!

Nice sharp corner to catch yourself on. Porcelain tiles can be like a razor.

Why not use your tile saw at 45 degrees?

Chanel locks work as well or a rubber mallet

How do you do it without a bow wrench?

I gotta shin for that.

You don’t leave spacing between your boards? Drainage? Rotting?

Thank you!

The duct needs to be smooth, like rigid galvanized steel duct. This aluminum flex duct wouldn't pass city inspection or home inspection when you go to sell your home. The reason is that grease catches on the ridges of flex duct, fire hazard. Also, over time the grease will just drip back down into your hood assembly.

This is superior to the similar tool that needs to be hammered into the top of the joist, which ruins the flashing tape. Well done!

If it is on the edge, what would you do?

Duh you act like it brand new been using one of these for more than 15 years

😅 good for you and those safety sandals! Thank you. What is is bracket called ?

Now, we just need the board streatcher

this is the easiest way if its only a few corners ,,some advise ,,dont trying get to fine on outside edge with grinder ,the slightest chip will ruin it ,do about 99 percent and if you overbevel past 45 apply a bead of caulk to fill void

I didn't even know that tool exists 😮

I don't remember why but you're supposed to leave like 1/8 of an inch Gap in between them just letting you know in case you're building a deck and your friends listening to you and showed you this video😂😂😂

Lumber sux so bad now days. I had to use a ratchet strap as a come along.

How bout not buy a bowed board that shit will come apart

I've been building decks for a long time you always leave at least a quarter inch gap between each plank for drainage this is all wrong

He has white skin,so that Trick is anglosaxon and OSHA approved 🤣🤣

Board stretcher 3000 is the correct name 😂

Very neat👍🙏🏻

My Dad would call that halfassing

Nice tool but I ain't decking boards supposed to have a 1/4 inch Gap in between them in case when the would get wet is swell and cause the wood to buckle

Damn that bit long long my guy 😂

How u take it out lol

God bless ya!

Can’t you just push it with one hand and screw with the other.🤔🍻💜🇺🇸✝️

Been screwing down a board 2" past where i need to close a gap, grab ye ol' flat bar or crow bar more ideally if its REALLY stubborn and wrench that shit back. 22 year carpenter but i've done just decks full time so this tool, if you're doing it daily or often for that matter would be ideal for sure.

Shouldn't there be a gap?