Thanks bud, have a good one

Wow you done it 👍 so proud of you.

please don´t quit your day job 🤣🙊😶

Where can I find consumables for my unit, 770795 is what I’m looking for….. thanks!

The tightenting handle on the fence looks like a lift twist type bolt

I have the same washer but the pump is leaking oil from the pump I guess that means its over for the pump?

What was the listing on Amazon? I have multiple springs broken on my c-10 truck. Do they have different sizes?

Where are you? :(

Hahaha dude that finger is DOOMED you’re destined to lop it off completely eventually 😂

Somebody help! I got a 1997 trooper ltd 4x4 3.2l automatic 4l30e transmission. I have code p0300 random misfire . I've done fuel injector / map/maf/plugs / coils .... everything but a new coil wire set. Was told it could be ecm.... pcm... whatever... True? Please help True?

Kevin, you still above ground? Haven’t seen many more post on here.

My oil leak was caused by me. My multimeter battery died and I couldn’t check for voltage but I’m pretty sure it’s the alternator because lol, …I was changing my oil, drunk, and stripped the cap that holds the filter in its housing. Screwed it on wrong. Wrong. Oil began to leak into the alternator causing smoke . It drove for a week after replacing the cap with a new un stripped one, then battery light and power steering light came on

When I took mine off, it started dumping pump oil out....but yours was bone dry. Why?

I think you did a professional job

I have trooper 2001, i having problem with gage jumping all the way and back.there is way to clean up that. ? here that oil pressure sensor is Pricy, $85

Good video! Thx for share buddy!

Thank you for this video, saved me over $100 on a new pump. I just got a new to me Used pressure washer that supposedly the pump was rebuilt, it leaked just like yours 15 min after using it. In your video, you mentioned the seals were only installed groove side down, mine we're not! thank you

How many cans did it take?

Good afternoon, a pleasure to be part of your channel. My name is Jimmy and I am from Quito Ecuador. I have a 3.2 Trooper Wagon, I am going to send you photos of my car so that you can please help me with suggestions on how to fix some things. Greetings.

Good tip. Thanks for sharing.

Just picked up a 1999 Trooper today. My 4th in the last 25 years. Green paint is peeling all the clear and I think the Monstaliner is the way to go. How long did it take you to do the whole truck?

Mobile ? Highest quality…. Not 🤣

The stock compressor oil for north stars is Amsoil sae 30/40 compressor oil .

Your video might be 5 years old, sure solved my problem today.

Hello sir,what isuzu model car is that? Trooper? Rodeo tfs? Kb250? What the code no beraing?

EXELENTE VIDEO Y EXPLICACION MUY CLARA, GRACIAS TENGO ESE MISMO PROBLEMA CON UNA GENÉRAC,GRACIAS

I have a 2002 Isuzu trooper, V6 3.5 4 x 4. I’m desperately looking for a transmission wire harness front to back. The plug at the front by the radiator has to have a blue black and green wire to the plug-in. Any suggestions nobody seems to have one.

Where did bought your Oil Pressure Sender Bro

Awesome Job

I wonder if your neighbor turns on his machinery so he doesn’t have to listen to you yelling. Thanks for the effort but why don’t you just talk normal instead of like you’re yelling to somebody 100 yards away

Good vid man! Everything I needed to know to fix the one I have identical to yours, and even ordered my parts as I watched your vid! Thanks again and keep these informational vids coming.

The distance from the retractor to the out part of the seatbelt is long enough to not interfere with the mechanism,the seatbelt probably is allergic to the dirt I really recommend if you give a Benadryl but your fight to open a KZbin channel to repeat all the stupidity are more bigger than your own ego

Nobody knows it was your wife the one with the noisy stuff, are you kill her after the video?

I have a generac clean power 37 model 01067-0 1500 psi. It runs, but it spits the water out of two square portals on the pump case. What must I do to fix this? The round seals seem ok.

i have a problem with that gauge, when start is o when accelerate goes the other way

You're going to cause a grease fire w/ that amount of grease in those bearing

Just like me. When I got my welder I stuck a street sign on a piece of plywood that I laid on a folding table and just welded all night. There wasn’t a single piece of scrap steel in the whole neighborhood I didn’t randomly weld to something or just use to practice my dime stacks on. Just for fun. Bought the welder out of curiosity because I was always interested in welding. Who knew a year later I’d temporarily lose my job and start a mildly successful mobile welding side business to pay my bills and keep everyone fed lol.

I just finished building my welding table and was wondering how to do this thanks for sharing the info do you know what would happen if you ran both machines at the same time? I don’t think I would Wilder one’s a plasma cutter and I work alone in my shop. I was just wondering what would happen if both were running at the same time.

Although the camera only has 1.0 megapixels, my Teslong TD500 Pro Articulating dual-lens inspection camera is ideal for borescoping engines. One can view the pistons, cylinder walls, head, and valve seats as well, it combining articulation with an side lens, a borescope that was released in October of 2023.

Where did you buy the seals?

🤣🤣that rewind

Will this discolor my blue seat belts?

Did you put torque on this? It sounded like there was a click.

Suck the big one

U forgot ur cooler and little grill..

Great job ,do u have the link for the lift kit, and do you still have the trooper ?

I have the same issue with mine and I wasn't even able to find an aftermarket sensor there were like 300 bucks that was a gotta buy one. I'm curious where you got yours from allthough sounds like it didn't last very long

WRONG!!!!!!!!!!!!!!!!! as far as the rotation pattern. Correct for rotation interval every 3000 miles. #1 off road shop on LI says front to back only!

Hi, Do you change the torssion bars? And what do you win when you change them ?

How wide are they? Most knee pads I've worn, especially the standard ones are a bit too wide for me If your knees are more skinny, do they stay on as well as those with bigger knees? Have you compared them to the built tough gel fit knee pads?: kzbin.info/www/bejne/iHbUgn6qiLmHi7Msi=UdO5c4RwwlwemJnT