Hello, is the tank under the cabin always open or does it have some kind of valve that closes when sandblasting?

Perfect, thanks

Our plunger has come off the rod several times, way more than I feel it should leaving the blaster inoperative. Along with the mushroom plunger wearing out only after a few hours of use. The blast cabinet has been more trouble than it’s worth, wish we could find some solutions.

Great upgrade, had mine fitted for a while and no issues. No doubt it'll still be a consumables part but that's the nature of dry blast, right? Well worth doing 👍

Glass bead is no good for removing paint it takes too long. Crushed glass is better or Ali oxide

very good video, 1000 for me

Very useful, wont be getting the 800lb, will need the 1000ld

Hello I just bought one of these cabinets second hand. I need to get a compressor that will run this machine for personal use. I plan on using it for wheels and misc car projects. I see that the machine on websites say it calls for 24cfm at 125 psi. Is the cfm more important or is the psi more important. This is all new for me and I know nothing.

My suction cabinet build by me is faster than your direct pressure and I don't damage aluminum wheels. I have yet to see a correctly built blasting cabinet in my 40 years of doing it. I run 18cfm at 1/2 inch hose to the gun. No pedal, no dust, no expensive of anything.

33% is the optimal ration.

what is the total floor space needed for the 100lb lift, 220cm for the main table but was is the total length when it is lowered and has the ramp fitted. with it being cantilevered I need to know if i have enough room to fit it in my garage. do you also have a video of the 1500lb lift as I notice that is a scissor.

Great video mate 👍

Can you show how to change the 2inch outlet part too if it's cracked

Very helpful! Now im seeing this was a bit more machine than i needed. Oh well, bought it off facebook, gonna learn by trial how to blast rust. Thanks!

I know this is an older video, I have this same cabinet, & need the dust collection for this, where can i Buy one? Not sure where to get one since one isnt listed in the boox

Marty what’s the best media to use

I’m thinking of getting the pressure pot blaster. I have a 72cfm road compressor. What dryer do you use? I can’t seem to find one. Thanks

Well done, I hope the unit that fell is ok

Just bought a used one of these and couldn't find instructions online. This video was very helpful. Thanks.

Hi. This looks like a great setup, especially as it rules out the need for a hoover with that dust extractor. I know it's on the low output side, but I have been offered a 3hp compressor for free (until I can buy a more powerful one) - would this be good enough to get started with sandblasting smaller items such as brake assemblies, car brackets etc? Thanks

Not a good idea unless the bottom rail, sidewall and top rail are all rust proof.

Two years gone by, have you had any problems with water in the hole?

In meinem Garten steht ein IBC 1000, vorgefüllt mit ca 500 Liter Regenwasser, diese möchte ich ungern einfach weglaufen lassen um IBC 1000 völlig zu entleeren. Meine Frage ist hierzu. Wenn ich die Abdeckung vorn unten abdrehe, was ist dahinter ? Nichts oder eine Art Verschluss-Segel, weil es ja noch einen roten Drehhahn gibt, welcher sich auch um ein Viertel dreh lässt. Ich habe dies zwar getan, aber trotzdem, in beiden Stellungen kam Wasser auch der Öffnung, wenn auch gefühlt gering. Ist der Tank entsprechend entfüllt, soll er bedeutend höher aufgestellt werden um zum Beispiel einen Eimer, eine Gießkanne, oder was auch immer daruter zu füllen, ohne jedesmal einen Schlauch anzuschließen, wenn man dies gerade nicht benötigt. Danke für Hilfe und Antwort. Zumindest eines der besten Erklärvideo bezüglich Anschlüsse und ihren Aufbau

Thanks a lot, dude, you have been a great help!

Would my Chicago hush 150 run one of these, its 20cfm

Great video, any idea if 50 litre 14CFM compressor attached with 100 or 200 litre air receiver would it do the trick? Thanks

Thanks for the video. Is this upgrade on the site yet, just ordered some bits and hadn't seen it. I was wondering if the O Ring for the seal on the feed plunger is available on its own? I bought a mushroom head on its own last year but didn't to fit it until last week. I've just ordered a new one to keep for when the other wears out and there is a kit with the plunger, mushroom seal and the O Ring. I haven't replaced the O Ring this time but I'd like to. Also, my cabinet is from a company in Derby who sound like they should be selling sofas rather than tools! They aren't much help with spares but the cabinet I haveis basically the same as the big pressure cabinet. Are the grates available for them? Mine are very worn now. I have two rectangular grates, one with a handle and a secondary one in the hopper (which is ok to be fair.)

I've been using that procedure for a while but I still always dread using the pressure pot blaster because fine sand will still clog the hose occasionally and these things are so awkward to work with to clear the lines, especially when full of sand!

Does yours make an insufferable high-pitched screeching sound? I’m in the US and I got one of the pressure pot cabinets from redline stands, who is the US importer of these types of cabinets. Exact same dust collector too. Except mine makes the most earsplitting high-pitched screaming, when under any load at all. And I’m thinking I may have a defect.

Is this with glass bead? Im wanting to use aluminum oxide sand media

Oh, thank you for taking the time to make this video.

Excellent video. 👍

Man that was helpful mate 😊😊

Hello mate, Did you need to wire the door switch to the control panel ?

Dónde lo compro soy de Peru

hi quick question, does the pik up tube connect thick end or thin end to hose, many thanks

Or get the biggest compressor you can, I got a 7hp petrol that can run all day long and refills the tank super fast.

How long did this last?

Hi, I just purchased this sandblaster. But it’s not sucking up the media effectively? Any help please!

Will the 800lb lift be ok for a push bike if its that crappie

hi there, Can you also use this unit for furniture or taking off the paint from stairs ? Thank you.

How do you drain the blasting media after use?

EH! Pardon?

What setup and medium would be good for removing mill scale from flat and square bar steel.

Hi,would like to know how much you sell these for,cheers Malcolm.

This video isn't much good unless we can find the parts to do it. Please provide a link other than the one you have because it goes to nothing. I got so damn excited to find an answer and yet I don't have an answer I'm left with more questions

So glad I found this video because I have yet to figure out how to get the whole thing off to replace it. Now that I see how easy it is I'm very excited but I cannot seem to find where to order those parts. Could you please share a link so I can purchase these?

Hi, looking to order the same cabinet asap but also want a carbide nozzle. Can you advise on the best size nozzle as the 6mm didnt seem to work in the video? I will also be adding a media valve to improve flow if that will make a difference to nozzle size. Thanks

Translated for U.S.: Max 10lbs of blast media, Max 80psi @ 5 CFM. Provide your own 1/4 air ftg and hose. Box weight 25lbs.

Thank you very much for this video, yesterday my bra broke and I had no idea how to change it. Very useful video 👍! ! !