What part number of that connector?

Awesome video, Gracias!

A minha máquina é igual não liga

The lighting and fixed camera position helped a ton, especially step by step so I could repeat in my head while doing it , used the wire method as well! Thank you @theapplianceman!

Excellent tutorial! Thank you!

With the help of this excellent video did this job a year or so ago. Zero leaks since then. Spanner tool was not available anywhere so I made my own. Most time consuming part of the job was the seal removal. Took about an hour; it was stubborn and I took it slow. No $90 tool necessary. Thank you very much Senor Acevedo for sharing your knowledge, and also for your Service to our Country.

Man you gotta clean that machine 100% next time. Nice explanation though

Fantastic tutorial!

Can water leak into agitator tube seal right below agotator? Mine leaks into the clutch and i think it gets so wet it will have slow spin. When it doesn't leak it will spin dry the clothes well. Also, when it leaks the tub brake lets the tub coast down on shutoff...ineffective brake. If I don't use the washer for a week the tub brake works (dry?)

I watched 2 of your outstanding videos to fix my dryer. The drum wasn't spinning. It turned out the idler arm pulley was seized, and it wrecked the belt. $65 for the parts, your expertise, and some elbow grease saved me a fortune on a repair call. Thanks for all your help.

Thank you so much. This 68-year-old woman just repaired her own dryer. The hardest part was trying to find a wire hanger in my house. Your step-by-step instructions helped save me a maintenance call. The install of the belt took less than 1 minute. I spent the next 10 minutes trying to line up the latch and holes on the front panel. Again, thank you.

How to take out dryer apart ?❤️ whirlpool cabrio help

Thank you for a fantastic video

Yep, I can do this! This is one of the best and simplest instructional videos I've ever seen. Thanks for putting in the tidbit about holding the drum in place. That's the point I probably would have started cursing. 🤬 😊

Love this. Thank you so much sir. 😊

Just wanted to thank you, if you hadn't shown me that trick to hold up the drum, I am not sure I could have pulled this off, I was having a heck of a time. That made it very easy.

Great video. I was going nuts and this was such an easy fix. Thank you!

Thank you Angel!

Brother I like the robot voice but I love your original voice it demonstrates that people of all nationalities want to contribute in helping our society and others worldwide. Thank you

This video thumbs down, you had plenty of time to show the diagnostic modes, thumbs down, sorry

U can't get to this behind the dryer

Awesome information. Thank you👍🏽

I’m not an electrician, but I think this is why he’s using a search protector

3:05 3:09 3:09 3:10 3:10 3:11 3:11 3:12 3:12 3:13 3:13 3:13 3:14 3:14 3:15 3:15 3:16 3:16 3:17 3:17 3:18 3:18 The washing machine sounds creepy.

Great Video! The best visuals of the multimeter and all. Thank you!

Thank you my good brotha

Doesn't say witch wire goes where. You have your hot and ground. With one does the hot wire attach too ?

Here's how to find the chapters in this video: 0:00-0:28 What to Check When the Washer Won’t Spin Properly (Diagnosing the problem) 0:28-1:57 How to Check the Spinning Speed 1:57-6:28 How to Check the Door Switch with a Jumper Wire 6:28-7:36 Replace Thrust Bearing 7:36-9:51 Remove Tub & Transmission Together 9:51-12:47 Replace Transmission 12:47-End Re-Install Tub & Transmission It's an excellent video. I wish more were put together this well.

This video was so precise and easy to follow for fixing my Whirlpool Idler Pulley. Well done, easy to follow.

What are the symptoms of the brake assembly not working correctly?

Thank you

does 120v to the motor and no blinking light mean that the inverter/motor is bad? - all other switches and control board check out okay

Hi Please I have the model LSQ9600LG0 but I don't know how to make it work Pls help

Very helpful! Many thanks!

I followed this by pulling the door switch up front but causing the switch to disintegrate. Now I have to buy a new switch. The rest of the tutorial videos I've seen on YT are to pull the front panel and remove the wires behind the panel. I have added an additional repair cost to the broken dryer 😢

I refuse to pay 😤 someone to come look at the dryer 😒 85.00 bucks 😤 everytime they come look at the dryer is insanity to me

Thank you!!!

recommend placing a hose clamp (#40) on washer tub to hold the tub seal in place. Go to all that work and if you don't install a hose clamp - the seal can come loose and water runs all over tranny and bearing and you end up with complete re-do of all your work.

My dryer will go around but if I put in a load of clothes it won’t spin. Why and thank you 😊🙏

3:33 welp, guess this tub ain't getting cleaned lol

thank you

Excellent explanation! It worked very well for my whirlpool dryer.very easy. Good tip not to take the screws out. Thank you!

This guys an idiot

So painful to watch just remove the wires from the rear of the door switch, it literally takes 10 seconds to take them off and 10 seconds to put them back on. There's no need to remove the door switch and feed the wires through.

Very goof

What is size of drum belt... been having trouble looking for it 1:59

One of the most straightforward videos I've seen. Thanks for keeping it simple .

Thank you

What kind of dryer is this where you can access the electronics from the back? My GE requires drum removal.

Thank you