Bhaiya ismein kam awaaz a raha hai😢😢😢😢

Your speaker is in bad condition.

Kitanw watt ka speaker h ye

Quería saber de cuánto es la batería del celular que le pusiste

Last Me Kya Diya Speaker me 🤣🤣🤣

High noise

Sir please help... Low sparking problem solution please 🙏🏻🙏🏻

this video shows only the transistor and its shape,

From where can I buy these transistors???

Not working

Manakah yang lebih baik dan stabil untuk digunakan

It is working??????

Can I replace tip42c with tip41c?

Fake video 😠😠😡

is it okay to use 12v adapter?

hey what happens if we use 5v or 3.3v?

Thank You for this Knowledge. You electronic's professional, dong it faster and another great method!!!!

Eccellent🙂

Very informative -excellent , will wach more of your videos...Thank You Sir⚡⚡

Need to know speaker ohms value.

Transistor 13001 is the worst choice for a audio amplifier, because it's small and easily overheated. The best transistor Choice is 13003, 13005, 13007, TIP41,

can i power it from 12v ?

P

Yeah bro its "ultra bass" and the sound is very "good" distortion is screaming

Gracias.Necesito daber. Que pasa si coloco un capacitor de mas microfatadios.Sube mas videos.Abrazos.

if you tryed this and you sound came out extra "noisy" its because the capacitor polarity is inverted

Great😄

Sir koi bhee lag sakta hai

the transistor go hot ...

resistor color code please

Hello Sir, please ek baat boliye Charger 5 volt dc connect to XL6009 se (7.2 volt Charge kar sakte hain) Or ( 4s BMS 12 volt ko charge kar sakte hain)

Schematic diagram please 🙏

Massa Parabéns

𝐩яⓞ𝓂𝓞Ş𝐦 ☀️

I've got a simple audio wiring question and this looks like a good place to put it. I have a 1/4" audio jack on the back of a monitor that I want to use to drive a pair of powered stereo speakers and a separate powered subwoofer. I'm using a simple 1/4" y-splitter to give me 2 stereo outputs from the monitor output jack. One side feeds the primary speakers and the other side feeds the subwoofer. To mix the stereo signal for the subwoofer, I combined the left and right wires and soldered them together, using the one ground wire for both. My problem is that the mono signal created by physically mixing the left and right channels for the subwoofer ALSO mixes the other side of the 1/4" y-splitter. This causes the stereo speakers to produce mono sound. I want to somehow isolate the signals after leaving the y-splitter. The issue became obvious after discovering it... electronics are not one-way... unless forced to be. The question then becomes, how should I split a stereo signal into two stereo signals and then mix ONLY ONE of the two into mono without affecting the other? Is it possible to use diodes to isolate the two outputs? How else should we approach this problem? Any comments, from anybody, would be appreciated. Thanks.

amazing video keep going

24v?

Good

Gôd

Nice video good video good video good 👍👌 👍👍👍👍

Hy . Hi . I am from Sud experiment KZbin channel . Do you like to collaborate with me

Sound not clear but not bad

It's not working with Android mobile

Audio kis liye nahi

Good

kzbin.info/www/bejne/pZ-Td2uQbdl2eLs

Thanks for the excellent video, sir; What are the specs for the transformer Volts in x volts out

Excellent video, sir. Objective, clear, hard work in favour of a community Congrats I used IRFZ44N but did not work... There must be some other problem The original trasitror was a KSH200 that was defective Any comments please inform. Tks

Very powerful

Please tell me the value of the resistor and capacitor capacitor how many volts and how much micro savings