You really need to make more Surron content these videos are great!!!

On the rear rotor I think you can drill the bolt pattern into the magura rotor that’s what milk racing do with there wheels

In your video you stated you don't want to cut the excess on the brake lines and get brake fluid everywhere, So does that mean they came pre-bled ready to mount and use?

What broke? Make it stronger, and do it again

can you make me spacer like yours so I can cut mine down too?

Odd you went with the small calipers, instead of the V4

pls link the parts

My stock brakes always felt like they wouldnt save me when i go past balance point, like it just kept falling back even grabbing a handful. Sure enough yesterday I sent it back kinda fast and the brakes did not save me. Slid on my ass, I'm so pissed because my new Hope techs are about to be put on.

hey bro, any idea what the size is on the headstem cap?? I wanted to get a kustomcap but can't seem to find the info anywhere

What forks are they? Need a adapter for the fastace forks

Where do you get your Sur-Ron from.?Where you get the super moto wheel with it bro.??

Subscribed. I want the same set up for my surron

Hello have u bled them yet or do they not need it

How do you switch from eco to sport?

How do you get the nipple covering the Allen on the stem

that radius work and attention to detail is crazy!!

the custom fab goes crazy, subscribed so quick

Where's the next video😭😭😭

Did you make those sliders?

More custom sur ron parts video plsss🎉🎊🎊🎊

More vid about custom parts plsss it's enjoyable. 🎉🎉🎊

🔥🔥🔥💜Content!!! Get the following you deserve = Promo-SM .

Did you just delete your Speedo and mode switch kinda like the clean look

What headlight are you using?

nice ride! got one of those rivers by me... that's what the boats are made for..

cool shop

Nice machining. I can’t stop thinking of such big machines to make small parts. Cool way to do the alignment. I’ve seen something similar using string to get the measurements. If you could get individual raised platforms for each wheel with rotating pads and raise the car to place it on top you could set the toe without raising and lowering each time.

Hello. I think you've been on board for a long time, did you charge the battery in the middle? I think it's still at the maximum

what part of iowa? i have two mini jet boats and live in southern iowa

Great video quick tip though, There’s no need to pry the collet out of the holder, when you put together an er style holder there is a small lip in the nut that you snap the groove in the collet in first then you start the nut and collet onto the holder then insert your tool last. When you do it this way the collet is pulled out by the nut when you take it off.

I would love a walk around of the boat. How you set up the water intake, controls, all that good stuff. Looks awesome!

Damn bro. Good work. Really cool to see the whole process. Glad I found your page.

get a twin blade solas impeller thank me later . Nice vid

I've had mine 5 months and cant wheelie even close to as good as you XD

Wow how did you manage to wheelie stock sur ron so easily ! I remember when I had my sur ron with stock gearing it was wheelie real easily from a stand still but when I was at rolling at 5 mph no more torque on/off kind of power curve. But I was with the cable throttle maybe it better with electronic throttle !?

Always supporting the good sur Ron vids. Nice wheelies!

how big of fuel cell are you using?

Where did you put your dash your horn and the other switches

Nice job but pegs should be wider👍

I saw your breaks vid and thought... with all thoughts mods how come the stock pegs ??? but now I know . my break pads died after 15 months and killed the rear disk with it. whoops since my bicycle is on year 11 with one set of pads, I never even thought to look. I put a street light kit on my Surron of my own design just roiled over on 2400km. love it.

Do you have a website to purchase those axel slider?

So sick man! I actually just bought one with the super moto wheels too! Can’t wait to review it as well!

Need those axel sliders asap!!!!

What are you gunna record in the winter??

you could just drill out the back rotor, ive seen a few ppl do that

My Tech 4 came bled was just plug and play .They truly do feel good and stop on a dime .

Amazing work and skills! Where can I get these?

Nice calico cat 😸 Soon I am buying Surron too 😉😄

Yasss! More videos like this of machining dope Ron parts and I guarantee your channel will take off! I would totally buy parts from ya also lemme know when you start to sell stuff!!

Mate could you make bigger brake calipers to accept motorcycle brake pads ? Mtb brake pads are too thin