21 күн бұрын
Пікірлер
@KseanNoel Күн бұрын
Where did you get the fog lights from?
@FC2Dani Күн бұрын
@@KseanNoel I got it from Amazon. Search up “10th gen Honda civic Lambo fog lights”
@MrAuhue 5 күн бұрын
I got klicking sounds from left wheel when drive to left in corners. So i think mine is broken to but on the other side. Its different or isn't? Any video from the other side?
@FC2Dani 4 күн бұрын
@@MrAuhue the other side should be the same thing. The 10th gen Honda Civic CVT doesn’t have an intermediate shaft. Both sides connect directly to the transmission. So it should be the same process.
@hix9306 11 күн бұрын
Did you go oem on the axle ? I’m getting this done tomorrow but not using oem axles
@FC2Dani 8 күн бұрын
@@hix9306 I opted for an aftermarket axle as a temporary replacement but later switched back to the OEM axle. My other axle was only two weeks old, but the CV boot somehow tore. As a result, I created another video demonstrating how to repair the CV boot and decided to reuse my OEM CV axle instead.
@hix9306 8 күн бұрын
@ did you end up having to get a wheel alignment after the axel change and lowering the car ?
@FC2Dani 8 күн бұрын
@@hix9306 I haven’t gotten one yet :0 My steering wheel is a bit misaligned and pulls slightly to the left, but I don't think I need one since it doesn’t effective my driving.
@hix9306 7 күн бұрын
@ ok yea same happen to me. I lowered it and it seemed fine but when I got the axel replaced it started to pull some and I just put on new wheels . Guess I’ll get an alignment
@FC2Dani 4 күн бұрын
@@hix9306 sounds about right. The first temporary axle I replaced seemed fine. After I did oil an change and tire rotation it started to pull. So I’d assume it’s just the tires.
@layzbaguette8340 18 күн бұрын
you can also use a rubber mallet on the outer axle side to hit it into the trans in case it doesnt wanna pop in just by pushing it
@FC2Dani 18 күн бұрын
Absolutely! Make sure to thread the axle nut to avoid damaging the axle, such as causing it to mushroom.
@mafiamafia3458 18 күн бұрын
great work continue ❤
@mafiamafia3458 19 күн бұрын
great job
@FC2Dani 19 күн бұрын
@@mafiamafia3458 appreciate it.
@whereswaldo9089 24 күн бұрын
Nice!
@whereswaldo9089 24 күн бұрын
You mean hot air intake? The stock box makes more power than the k&n gotta go with PRL
@Chaos-jy8ys 14 күн бұрын
Could you elaborate plz?
@whereswaldo9089 14 күн бұрын
@ cause it’s enclosed and not open like this K&N which sucks in the hot ambient temperature inside the hood
@pentagon2386 27 күн бұрын
Good video
@FC2Dani 23 күн бұрын
4:23
@ethvn. Ай бұрын
where did you get ur duck bill spoiler
@FC2Dani Ай бұрын
@@ethvn. Amazon :)
@theeskuichi2256 Ай бұрын
Ima try this at home
@chrisa9164 Ай бұрын
Do I still need stock bumper on to install?
@0nly.nesh_ Ай бұрын
Just a muffler delete or resonator as well?
@FC2Dani Ай бұрын
@@0nly.nesh_ just a muffler delete. Resonator delete will make the car raspy. I don’t wanna make my car into the “Honda” car…
@0nly.nesh_ Ай бұрын
Another question. Did u use a 3 inch tip or less ? I wanna make sure it fits if I buy a diffuser but I might skip out on the diffuser. I don’t like the styles they got for this car
@highstakes9696 3 ай бұрын
Just bought a 10th gen 2.0. Looking to do the same
@FC2Dani 2 ай бұрын
It’s the best one on market from what ppl say.
@duketogo666 3 ай бұрын
Looks like you received 3 clamps from PRL, 99% sure that mine was missing the small vent tube clamp, but fortunately I had something around since the stock clamp is too small there. What camera are you using btw ?... it was very clear, great production!
@FC2Dani 3 ай бұрын
It’s a GoPro hero 12. 1080p | 60fps I should’ve been more aware of the camera angle though. So sad :(
@SubaruRR 3 ай бұрын
Is this suitable for civic hatchback 2021?
@FC2Dani 3 ай бұрын
yep
@Burn12345 3 ай бұрын
Thank you! Followed your steps
@PaulBelieberZ 3 ай бұрын
Does this bumper fit in EX Hatchback 2020?
@FC2Dani 3 ай бұрын
@@PaulBelieberZ yep
@Wheredatruth_at23 4 ай бұрын
Awesome video man. i finished the whole job in 40 mins! Thank you for clarifying the order in which tire to start at first. I only work on older cars so i didnt know the ABS can flip the order
@FC2Dani 4 ай бұрын
It’s weird right? Usually you start from the furthest away from the brake reservoir, but Honda changed it up.
@Wheredatruth_at23 4 ай бұрын
@@FC2Dani Do you do all your own basic maintenence? I've done every fluid except the blue coolant so far. Anything that might be good to know before i start? 2019 Honda Civic EX btw
@FC2Dani 3 ай бұрын
@@Wheredatruth_at23 I do indeed do all the basic maintenance myself. I accidentally deleted my (how to change spark plugs) video during editing. So sad :( I actually haven’t done my coolant yet. But it’s easy. 1.) there’s a big plastic wing nut on the bottom of the radiator, open that to drain it all. 2.) using a special coolant adapter funnel thing fill it up with DISTILLED WATER 3.) Run the car/Drive it for some short time before it overheats 4.) Drain it 5.) fill it up with OEM Coolant 6.) may need to pump (squeeze the coolant tube) to “prime” coolant or remove air bubbles. I think that’s it from what I recall. Using distilled water so it doesn’t rust and doesn’t have any chemicals in it like chlorine or something.
@sonyyoung1036 4 ай бұрын
I believe after you bleed all sides and engage parking brake 5x you are supposed to do a 2nd bleed of both rear brakes to clear out any potential air from the parking brakes.
@FC2Dani 4 ай бұрын
@@sonyyoung1036 indeed. I’m pretty sure I said that 😅 maybe idk
@ShiftK 3 ай бұрын
@@FC2Daniyes you did at 2:33 This video helped me a lot, thnx!
@SPLITTINIMAGE 4 ай бұрын
Any more clips? Maybe some in car? It sounds good!
@FC2Dani 4 ай бұрын
@@SPLITTINIMAGE I’ll try to get some in cabin sounds. I did put some sound dampers in the trunk
@Froppy00 4 ай бұрын
thanks
@FC2Dani 4 ай бұрын
No problem. Hope it helped
@isaiahroach1967 5 ай бұрын
if you don’t mind my brother how much did cost for the exhaust work
@FC2Dani 5 ай бұрын
$200 there were other cheap shops offering around $100 but I needed it done Asap so it's whatever :d
@SirCumcisi0n 5 ай бұрын
how much did it cost to cut and weld?
@FC2Dani 5 ай бұрын
All depends on the shop. Mine charged me $200. It's a lot compared to others ($100) but I had to get it done.
@bernandoturner4840 5 ай бұрын
I dont like mine Loud.👎🏾😊
@FC2Dani 5 ай бұрын
The drone is eha. Compared to other cars It's not nearly as loud.
@jude2768 5 ай бұрын
How are the rotors so far? Planning to change mine soon.
@FC2Dani 4 ай бұрын
I have a hairline vertical crack from the hub up. Also making some grinding/squealing noises when it’s hot. Not sure what the problem is, but I’m going to inspect it very soon
@brainbuster4u744 Ай бұрын
@@FC2Dani Did you figure out what was wrong with it? Installation error or simply bad luck or poor manufacture quality? I am looking to put one in on my Lexus IS
@FC2Dani Ай бұрын
@@brainbuster4u744 I think it’s just cheap quality Chinese steel. For $200 for all 4 is kinda wild. Good quality rotor for one is around $100
@theultimatekid1209 5 ай бұрын
What was the easiest way to take off ur duck wing?
@FC2Dani 5 ай бұрын
@@theultimatekid1209 I had to destroy my wing to take it off 😭. The 3m I put on wouldn’t budge, I also bent the trunk lip a little bit 💀
@theultimatekid1209 5 ай бұрын
What did u ask for when you wanted the exhaust to be where the diffuser exhaust was ?
@FC2Dani 5 ай бұрын
@@theultimatekid1209 I just told them to align the exhaust tip in the center of the right diffuser cutout. From there the muffler shop did their magic.
@theultimatekid1209 5 ай бұрын
@@FC2Dani thanks
@tyjackson3448 6 ай бұрын
I have the same intake and after about 2 years the intake pipe turned into a grenade
@rubencoolidge354 5 ай бұрын
What do you mean by this?
@KrookDaKidd 4 ай бұрын
That doesn’t even make sense
@brandenwilkins2820 6 ай бұрын
10th gen looks pretty identical to my 11th gen are any parts the same do you know?
@michaelmurdock3366 6 ай бұрын
They’re almost identical mechanically, k&n makes a intake for the 11th gen 2.0 L I just ordered one!
@FC2Dani 6 ай бұрын
Same concept since it’s the same 2.0L however it won’t really fit cause the design of the 10th and 11th is different.
@thumperbangin2000 7 ай бұрын
U like it? Im thinking of doing this same one on my 11 gen.
@michaelmurdock3366 6 ай бұрын
Mines coming on Thursday, will update once I install!
@thumperbangin2000 6 ай бұрын
@@michaelmurdock3366 cool lmk
@FC2Dani 6 ай бұрын
A few videos later I will also Review the PRL HVI for the 2.0L !! So stay tuned!
@michaelmurdock3366 6 ай бұрын
I can 100% recommend it, it sounds crazy I love it
@thumperbangin2000 5 ай бұрын
@@michaelmurdock3366nice, just ordered mine.🎉
@steveeemadden431 8 ай бұрын
Share link for bumper pls looks clean
@FC2Dani 6 ай бұрын
Should be in the description!
@iDusk 8 ай бұрын
You got the insta for the white hatch? I am looking to do a similar build
@FC2Dani 6 ай бұрын
No sir he does not.
@Xyberlool 8 ай бұрын
Can you send a link to where to purchase the full kit of the SI
@FC2Dani 6 ай бұрын
Should be in the description
@frias2287 9 ай бұрын
Good job bro 👍
@MJ-df1kz 9 ай бұрын
How was it? Planning to change mine aswell i have 2020 hb sport
@FC2Dani 9 ай бұрын
So for so good. The Braking power is slightly more aggressive due to the “slots” grabbing more brake pad. FYI the drill and slots rotors will wear out your brake pads more than the oem (smooth) rotors.
@antonsavelyev4258 Жыл бұрын
Damn how long that take doing all 4 wheels?
@FC2Dani 6 ай бұрын
4hours+