2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
Пікірлер
@beniscooked 7 ай бұрын
This is great man - nobody has the preinstalled seal+housing anymore - everyone is out of stock except Bimmerworld, who wants nearly $400 for the kit. Decided to do this after ordering a clutch/flywheel kit or my slipping clutch on my E46 M3. Gave me the confidence I needed to just order the seal + gasket :)
@timlovick87 7 ай бұрын
Soooooo. No1 has a video of how they got it out 💀
@MODINDUSTRY7 7 ай бұрын
@@timlovick87 kzbin.info/www/bejne/rYHcZXttjZd5mNEsi=sNYkncWRekpnpaOn
@emilepapillon2275 8 ай бұрын
how did u get the old one out?
@MODINDUSTRY7 8 ай бұрын
kzbin.info/www/bejne/rYHcZXttjZd5mNEsi=7Xhh1SDGJDq06_F3
@B_Complex_BF 8 ай бұрын
Bread and a either a 14 or 15 mm bolt. I had troubles not getting a good enough seal so I bought a bolt that fit tighter. Just keep stuffing it lol
@B_Complex_BF 8 ай бұрын
Grabbed my 7/8s socket and just tapped it in. Thank you for the help
@MODINDUSTRY7 8 ай бұрын
Thanks for watching 😎
@juicewrldclips6523 Жыл бұрын
Why not just replace the whole valve while you’re in there??
@MODINDUSTRY7 Жыл бұрын
I did not want to spend $60 for a new valve especially when considering the low mileage on the engine. It's always a good idea to weigh the cost and benefits before making a decision like that and the valve looked okay when I pulled it out just needed a new o-ring. Sometimes, it's worth taking a chance on a more affordable option, especially when it comes to car maintenance. It's all about finding the balance between quality and cost.
@jonathanscottpenny Жыл бұрын
Did you do it on the ground? How long did it take you
@MODINDUSTRY7 Жыл бұрын
I did it in the middle of a clutch job but I’m sure you can do it in a Day
@jonathanscottpenny Жыл бұрын
@@MODINDUSTRY7 and was it done on the floor?
@razorracer6524 Жыл бұрын
Hi, i also have an e46 m3 and i can move the drive shaft in the back of the differential a bit, like a centimeter, when the wheels are on ground. Is this normal? Sry for the bad english
@Juke-Redlin Ай бұрын
Yo if you still have that car, if its the tiniest wiggle you'll be okay, but if you have significant wiggle, clanking when you wiggle it, you would want to look at a new drive shaft at some point.
@HD33P1 Жыл бұрын
Do you need to replace anything prior to installation?
@MODINDUSTRY7 Жыл бұрын
Yes, replace the front and rear differential mounts check for leaks from axel shafts and rear pinion shaft , if they are leaking replace the seals replace the fluid .
@betatester2560 Жыл бұрын
so many ppl do not know how to work on the drive shaft
@MODINDUSTRY7 Жыл бұрын
Why do you say that ?
@DonBMW Жыл бұрын
Dont forget to add some thread sealant to the two larger bolts at the base of the housing. These are oil passage bolts. Without sealant this bad boy will leak like a mofo. I like to ise Versachem #2 Thread and gasket sealant. Have never had a RMS leak.
@MODINDUSTRY7 Жыл бұрын
I hope mine doesn't leak
@DonBMW Жыл бұрын
@@MODINDUSTRY7 Hopefully not! Check out that product though. I’ve used it extensively. Great stuff for paper gaskets and sealing housing bolts. Have used it on trannies, RMS, water pumps and shifter housings. Never had a leak.