Ketchup & Mustard Racing 🏁

Пікірлер

@avihadad3915 2 күн бұрын

Thank you for the video. It’s nice watching the process. I still feel better sending it to my suspension service center than doing it myself. Love your little tricks and practical methods. What I’d really like to know is how and where in the world did you learn how to do this ? Cause it’s impressive.

@_MotoMikey_ 4 күн бұрын

Great video man. Thanks. How much oil do I need for 2 forks? Is 1 liter enough? Thanks

@canopyjunkie Ай бұрын

haven't done a "newer" R6, wanted to see if there was anything weird about them... pretty straight forward / great video. Only caviot, Fun fact about fork oil, there's no "standard" for weight across brands, the weight is a comparison only within the brands lineup.... so changing brands is likely changing the weight, even if the number on the bottle is the same, so changing brands may require a re-tune also.

@davidak478 Ай бұрын

nice cinematic

@hayleecarter5419 Ай бұрын

🔥🔥🔥

@faizalifaysal9386 Ай бұрын

Very beautiful bike ❤

@ketchupmustardracing Ай бұрын

thank you!

@yeejay6396 2 ай бұрын

Damn fine video man! 1 good thing about the 2nd Gen ('03-'05) is that the air box and fuel tank were seperate. No need to disconnect lines, instead of syphoning gas, you could prop the gas tank from the pillion seat latch, it's not a fantastic solution, just unless major component word is needed it can come in handy. You can still do all this and then some without needed to mount the bike to a stand/wheel mount.

@sportriderpr 2 ай бұрын

Good training 💪

@MrGhoulie 2 ай бұрын

How long do you think this would take to do?

@ketchupmustardracing Ай бұрын

Two hours give or take, depends on how mechanically inclined you're and your toolset.

@bryceg6412 3 ай бұрын

Nice work

@michaelpitta2047 3 ай бұрын

I’ve been trying to find one for weeks, does anyone know what the piece above the battery is that holds the seat in place is?

@jekpom 20 сағат бұрын

Late af but are you asking what piece holds the seat in place? There’s a hook that slides into a hole at the front of the seat, and two bolts on the end where you have to pull back the cushion that holds it in place.

@yasenschannel2337 3 ай бұрын

Nice job on the video and walk through. Background music was very distracting though. Are those cap bolts really 36mm? On my 2007 Yamaha r6 they are a 41mm I believe.

@Pszczola600 4 ай бұрын

Hi I have a question. Do you know how tight should I tighten the screws at the top?(I mean how many Nm) I only found in the manual how many Nm tighten the screws holding the wheel. It would help me a lot

@Ryan_1997 3 ай бұрын

What ever it is it should convert to ft lbs in the torque wrench when you set it. It’ll be in the dial

@jordyechevarria8040 5 ай бұрын

Why take off the tank though?

@ketchupmustardracing 5 ай бұрын

How else are you supposed to get to the spark plugs? It’s very simple to remove.

@jordyechevarria8040 5 ай бұрын

@@ketchupmustardracing But unnecessary and waste of time

@ketchupmustardracing 4 ай бұрын

@@jordyechevarria8040 so don’t take it off? 😂 you sound goofy.

@ketchupmustardracing 4 ай бұрын

Nobody is forcing you to take it off

@ketchupmustardracing 4 ай бұрын

@@jordyechevarria8040 I removed it so I have more room to film and I also don’t want it to fall over. Fuel pumps are fragile and expensive.

@Yamaha_Alpaca 6 ай бұрын

Fellow synth wave enthusiast ✌️Sweet bike!

@ketchupmustardracing 6 ай бұрын

Thanks ✌️

@jasonsarmiento3029 6 ай бұрын

Not sure if it’s just me but every time I watch a bike video, if there’s a track related sticker, I always catch it lol. Thanks for the how to. I was looking for an online service manual to follow and this will probably supplement that once I find a manual.

@viniciuss.soares5527 7 ай бұрын

Greatest bike in existence

@CharlieRafferty 7 ай бұрын

Best Thorough walk-thru of this fork seal job I have seen. Wish you had it up four years ago, when I last did this on an R6 - I saw here that there were a coupla steps I omitted completely, and I didn't make note of all the adjustment settings. I'm feeling much better about getting it Totally Right this time!👍👍👍

@yiannishayabusaofficial 8 ай бұрын

sound is magic

@zachary_2222 9 ай бұрын

Awesome video man. I’m about to do this on my 2011 r6. One question, I’m looking for the torque spec for the pinch bolts holding the forks into the triple clamp but can’t find it anywhere? How did you clamp them back in, and is blue locktite necessary?

@solidhamster Ай бұрын

17 ft-lbs is the spec for a 2003-2005, so it isn't much

@jermanerobinson4576 10 ай бұрын

Hey man, great video! I've worked on practically every part of my bike, besides the forks, and now in need of replacing the fork seals. This was definitely very informative. What was the white grease you were applying to the seals? Is that just any regular bike lubricant?

@ketchupmustardracing 10 ай бұрын

Thank you sir! if you have any questions feel free to reach out! ..... as for the grease, I'm pretty sure its white lithium grease, its just a small layer to help the seal slide into the fork, and it helps with the initial first few miles of movement where it would otherwise be dry.

@fishingXhobby 11 ай бұрын

I would like to know how much cost for this labor fee in a local shop in Los Angeles. My R6 Is overdue fork maintenance and I need to get it done 😊

@ketchupmustardracing 10 ай бұрын

I’m on the east coast, most of the time they charge more if you bring the entire bike. If you remove the forks and take just those to the shop, they can have it done in one to two days for a lower price; less work.

@Ryan_1997 3 ай бұрын

Same

@raymonddd27 11 ай бұрын

Isn’t bad to remove the fuel tank? I read somewhere it let’s air into the fuel lines. Correct me if I’m wrong please

@ketchupmustardracing 11 ай бұрын

I’ve never heard of it being bad personally, but to rid the fuel lines/system of air bubbles; i always flip the key switch with the starter button on multiple times to prime the lines and push out any air. The short noise you hear from under the tank is the fuel pump priming the fuel injectors for startup, it starts right up with no issues for me if I make sure to prime it after I’ve removed the tank for service.

@raymonddd27 11 ай бұрын

Awesome thanks!

@ketchupmustardracing 11 ай бұрын

@@raymonddd27 anytime!

@yungsuh8888 Жыл бұрын

goddamn excellent video. Perfect angles and lighting to see all the work/locations. Love the fact you CLEARLY showed which bolts, wires, parts, etc to remove, and which new spark plugs you used. Fantastic attention to detail

@ketchupmustardracing Жыл бұрын

Thank you brother, I appreciate you watching!! 🤙🏾🤙🏾

@brucehamman4201 Жыл бұрын

Heck yeah thanks for the link on the kit awesome video 💪🏼🔥

@ketchupmustardracing Жыл бұрын

Thank you!! 🤙🏾🙏🏾

@brucehamman4201 Жыл бұрын

@@ketchupmustardracingyes Sir hey what size of socket was that?

@ketchupmustardracing 11 ай бұрын

@@brucehamman4201 I’m not sure, which part of the video was it?

@omarhossin1413 Жыл бұрын

Does it have to be empty of fuel?

@ketchupmustardracing Жыл бұрын

No you can keep the fuel in, I suggest running it lower than full before changing tho just to be safe! 🤙🏾

@jessymaccartniy1646 Жыл бұрын

Зря ты его выиграл,теперь он тебя застрелит

@gannieshekhar4493 Жыл бұрын

nice, got me feeling like I just watched a ChrisFix it video.

@joshdalton275 Жыл бұрын

Agree with the others, awesome video man thanks 👍

@hisnameishiro Жыл бұрын

what about a left footpeg?

@ketchupmustardracing Жыл бұрын

That video going up this weekend 💀💀💀

@Voltaic_Rider Жыл бұрын

Immaculate vibes!!

@yiannishayabusaofficial Жыл бұрын

WOW AWESOME INCREDIBLE SUPERB

@2FindOut Жыл бұрын

How did u manage to find the slowest GSXR ? I see ur Dyno Jet

@ketchupmustardracing Жыл бұрын

Haha 👍🏾

@B58Rudeboy87 Жыл бұрын

The one thing I can’t see myself doing but I got mad love and respect for y’all. Straight 🔥 🔥🔥🔥🔥💯💯💯💯💯💯

@thebigbear79 Жыл бұрын

Solid day with the homies. 🤘

@jimmy737 Жыл бұрын

No gloves? Really 😂

@ketchupmustardracing Жыл бұрын

Im on the white bike wearing gloves

@NITTYGRITTY1000 Жыл бұрын

The frame is cut under the air box I’ve never seen that on a 2co r6

@ketchupmustardracing Жыл бұрын

Yeah I thought it was odd but it’s made that way. I checked

@yiannishayabusaofficial Жыл бұрын

WOW AWESOME

@TROllingNINJA2031 Жыл бұрын

Lowered GSXR?

@ketchupmustardracing Жыл бұрын

Very

@SacramaniacCc Жыл бұрын

Is that a custom reservoir bro? Love the clear and black top on it looks better then those white ones with black cap from factory. Never seen that!

@ketchupmustardracing Жыл бұрын

Yessir! It’s a RIZOMA reservoir!

@Jeepen_4_Life Жыл бұрын

Is that the song off of Biker Boyz?

@ketchupmustardracing Жыл бұрын

👏🏾👏🏾

@Vaulter1314 Жыл бұрын

I subscribed bc I can and nothing makes me happier than bikes

@ivantrujillo9528 Жыл бұрын

Que chingon

@zackarymckay1375 Жыл бұрын

Freedom

@floatinsun Жыл бұрын

No body gear 😢 extremely dangerous

@paiterisnikos Жыл бұрын

Nice Bro !Super thanks!!

@everythingrc2324 Жыл бұрын

Best 600 ever made

@BorisBIELECKI Жыл бұрын

Organs donnors

@followthesapper324 Жыл бұрын

Take yourself out, cool. Take your mates out, cool. Take an innocent person out, uncool.

@georgeshaw1675 Жыл бұрын

I'm glad he knew how to ride

Ең жақсы KZbin

Пікірлер