Do you know if a small filter is needed? I would be worried trash inside tank. I mean if it's new should not be dirty. Just asking

Nice, concise Vid on the install. Part of the reason I ordered one. I made the mistake of measuring once and thought I'd clear but she's just a bit too fat. '19 Chevy 2500, 6'7" box running a gooseneck and that's fine. The Companion 5th wheel slider hitch won't drop in with the tank in place. Just too deep by a few inches. Still going to run the tank for now since I don't have a 5th wheel yet, and it'll be easy enough to pull when needed. Thanks again. Great vid.

I have a 2015 and after watching how amazing the guard looks in yours I'm getting one. Thanks for sharing.

Our Keystone (same skylight) is cracking at the edges inside the RV. Only a year old.

I also live in Texas and learned years ago to protect my vent covers and skylights with horse stall rubber mats. You can find them at Tractor Supply. When we are finished camping for the year, along with winterizing the RV, I put my horse stall rubber mats over each of my skylights and vent covers so I don't have to worry about hail storms in the spring. The mats are made from a heavy rubber and I've never had one blow off even with 75 mph winds. When I remove them in late spring, I roll each one up and secure with with heavy duty Velcro tape to keep them rolled up. These mats are heavy to climb a ladder with, but it's much easier to do and less expensive than replacing your skylights every few years.

Where did you buy the bracket kit at???

I just installed the same tank. Did you put the springs in the correct place? My instructions showed on top of the tank tabs.

nice

Self tapping screws don’t need to be drilled first. They self tap.

Do you have part numbers for brackets you ordered?

What about some rubber bushings under the tank lips before bolts go through??

Silly question but due to the “anti siphon” valve that is tapped into the filler neck I presume that fuel will not back up against the factory filler cap? And fuel level in stock tank should level off at the anti Siphon valve? So I theory if u opened factory cap fuel should not escape because the fuel level should be lower than cap…??

How fast does the fuel drip into the system?

Very nice and informative. Been looking for a way to add range to the rediculus 25 gallon F350 nightmare especially when pulling 43 foot Cyclone Toy Hauler!!! AND NOT COST 2000 BUCKS !!!

Thanks for sharing with us

Any problems with it ever over filling or pushing it out the vent on main tank? Looking at doing this exact set-up under my bed cover and over filling is my only concern

Really great informative video. I just got a new to me 350 Lariat and in my research missed the all important info that my truck only has a 26 gallon tank. What does the fuel computer say when the auxiliary tank is keeping the main tank full longer? I’m assuming it just stays at whatever it said when you filled up until you use enough fuel to sense the level dropping.

Was this for gas or Diesel engine? There don’t seem to be too many options for the 6.2L Gas engine

Can you get the full 32 gallons in it?

Thank you for the video.

Put a tarp over the roof so hail won't damage it

I'm considering using a pump or at least an electronic valve to open with the Upfitter switches while in motion.

Lol irony..... Tho I am looking to buy a slight different model (notched 40gal), we have a 2016 F350 in Ruby Red with a Roll n Lock. Haha 😂. So my measurements I figured it would tuck under the RnL with space but seeing your video, I see I have plenty of room!

It looks like you used the bolts supplied by ranch hand for the grill to the frame. My install paper said reuse the factory 18mm bolts.

Is there a reason why you didn't clean the bottom sky light?

What type of lap sealant did you use between the new skylight and the roof?. Was it the same as the self-leveling you put on top of the skylight and screwheads after installation?

Mr. Russell, so after 2 years, has there been any wear issued that you mentioned in your video? Curious about the filler neck valve sitting right under the bed and touching. Also, how has the bolting held up? I am curious since the bed is just sheet metal, if the holes have wallerd out any.

Looking to do the same tank install in my 2011 f250, but my rear roll-top bed cover only has 8” clearance between roll-top & bed. How tall is this tank? How much space did you have between bed & you roll top cover canister?

Very informative, thank you sir.

So my tank was finally installed. The installer didn't run a vent line from the pressure valvue to the outside of the truck.. It got pretty hot today and the pressure release valve spit fuel out onto my bed etc. Have you noticed any fuel being passed through the pressure valve line you have set up?

I just got the 60 gallon tank installed. If you leave the valve open have you ever had an issue of your tank overflowing?

How wide and long is the tank itself (without the install tabs). I think they state 19”, but did not know if that includes the tabs. Nice video thanks.

That’s a nice clean roof

When you cut the filler neck hose did you have to remove a section of it or just cut and spliced it in?

Hi Matt, hey just wondering if you could just strap down the tank instead of using the bolts to secure it? Say if you needed extra bed space when you're not towing?... or could a guy just unscrew the mounting bolts? Thanks!

The aluminum vs the steel will the aluminum last forever???

I would get one for a s10 ls swap. The tank in a S10 is small

Great video and I’m interested in getting the same tank. I just need to research whether it will work with our Superglide sliding 5th wheel hitch.

How many tubes of lap sealant did you need for the project

Sola

I want one

Glue a mirror above the gauge. The image will be right side up.

in mexico we have deal with cheap -ass brands.

Matt, I appreciate the video as it answers almost all my questions. The ones I have leftover are; 1) did you find it necessary to remove your hard-cover to install the tank? I have a Retrax rolling aluminum cover and I am thinking it will have to be uninstalled to facilitate installation. 2) the pictures and your video show the filler, the vent next to the filler, and on the opposite side, also on the top of the tank, another opening, not the one at the bottom for the fuel line. What is that opening for and how many inches does that stick up in total height or height above the tank surface? It is not mentioned in any literature from RDS. My tray for the rolling bed only give me about 9 1/2 inches of clearance. 3) the vent tubes from your rolling cover tray, did they clear the tank or did you have to make some adjustments? Again, thank you for the video, and Happy Father's Day!

Does it fill factory tank slow or fast ?

All this talk about a big monster grill, and all I heard was "look, my hands are cold".

What is the measurement from the bottom of the tank to the top of the vent valve? Trying to determine if it will fit under my toolbox.

Do you remember what size the hose was

Noticed that you have it installed under a hard bed cover. I was thinking about doing to same with my truck but was wondering if you always have a diesel smell when the hard cover is closed.

There customers service is LESS THEN 0 stars !! Buy any other brand!